1. Introduction
This manual provides detailed instructions for the Voktta ZS-X11H V1 DC Three-Phase Brushless Motor Controller. This board is designed for controlling DC brushless motors equipped with Hall sensors, offering wide voltage input and high power capabilities. Please read this manual thoroughly before installation and operation to ensure correct usage and prevent damage.

Figure 1: ZS-X11H V1 BLDC Motor Controller with Hall sensor wires.
2. Features
- DC three-phase brushless control board requiring Hall sensors for normal operation.
- Applicable only to DC brushless Hall motors with an electrical angle of 120 degrees.
- Newly upgraded BLDC wide voltage 6-60V high-power 400W DC three-phase brushless Hall controller.
- Supports PLC 0-5V analog control.
- Supports PWM control with an amplitude of 2.5-5V.
- Stable performance with forward and reverse stop braking function after patch process upgrade.
3. Specifications

Figure 2: Product Parameters.
| Parameter | Value |
|---|---|
| Model | ZS-X11H V1 |
| Working Voltage | 6V-60V |
| Maximum Current | Rated 16A, Peak 20A |
| Maximum Power | 400W |
| Overcurrent Protection | Yes |
| Operating Temperature | -40~85 °C |
| Working Mode | Open Loop |
| EU LVD Voltage | Below 50Vac or 75Vdc |
| High-concerned chemical | None |
| Certification | CE |
4. Setup and Wiring
Before powering on and testing, carefully read and understand the following instructions. It is crucial to ensure correct wiring to prevent damage to the driver board or motor.
4.1. Connection Points Overview

Figure 3: Hall Driven Plate Function and Connection Labels.
- MA MB MC: Motor phase line outputs. Connect these to the corresponding phase lines of your brushless motor.
- VCC GND (Main Power Supply): External DC power supply input (6V-60V).
- 5V GND (Motherboard Power Supply): Provides 5V power (external power supply current should not exceed 50mA).
- SC (Speed Pulse Signal Output): Interface reserved for speed pulse signal output (no technical support provided for this interface).
- DIR (Direction Control): Forward and reverse control interface. Low level is effective for an external switch connected to ground.
- STOP (Stop Control): Stop control interface. Low level is effective for grounding an external switch.
- BRAKE (Brake Control): Brake control interface. High level is effective for a 5V external switch.
- Speed Regulation Control: Signal input for speed regulation. The board has an integrated potentiometer for speed regulation. Alternatively, an external 0-5V analog PWM dual signal can be connected for speed regulation.
- Ha Hb Hc +5V GND (Hall Signal Power Supply Input): Hall signal input interface. Motors with Hall sensors generally have 5 corresponding wires.
4.2. Hall Sensor Wiring
Brushless motors typically have 5 Hall cables: 2 for Hall power and 3 for Hall signals. It is crucial to correctly identify and connect these. Hall power cables are usually red and black (though colors may vary by manufacturer). The three Hall signal cables are often marked 'a', 'b', 'c', and should correspond to 'Ha', 'Hb', 'Hc' on the drive board.
4.3. Motor Phase Line Wiring
The motor has three relatively thick phase lines, which connect to the MA, MB, and MC interfaces on the drive board. Ensure these are connected correctly. Once confirmed, the main power supply can be connected.
4.4. External Signal Speed Control Wiring Diagram

Figure 4: External Signal Speed Control Wiring Diagram. Note: Positive and negative brakes are high-level effective PWM control, requiring an amplitude of 5V and frequency of 1k-20kHz.
4.5. Debugging Unclear Interfaces
If the motor phase line and Hall line definitions are unclear, follow these steps:
- Connect the three motor phase lines to the drive board's phase line interfaces (MA, MB, MC) at will.
- Connect the three Hall signal lines to the drive board's Hall interface (Ha, Hb, Hc) at will. Ensure the two Hall power supply lines (+5V and GND) are correctly identified and connected.
- During the initial power-on, debug with low voltage and low current. If possible, adjust the constant current power supply to 7-12V and the current to 1-2A.
- Exchange the sequence of the three Hall wires in any order (swapping any two Hall signal wires between the motor and the drive board) and perform a power-on test each time. Continue until the motor rotates smoothly.
There are 6 possible Hall phase sequence combinations. The motor should run smoothly with high torque at low speed when the correct combination is found. If the motor does not rotate or exhibits abnormal behavior, the wiring is incorrect.
Hall Phase Sequence Connection Methods:
- 1. Ha Hb Hc
- 2. Hc Ha Hb
- 3. Hb Hc Ha
- 4. Ha Hc Hb
- 5. Hb Ha Hc
- 6. Hc Hb Ha
The motor phase lines (MA, MB, MC) can remain fixed while only adjusting the Hall signal lines.
Video 1: Overview of the ZS-X11H V1 BLDC Motor Controller.
5. Operating Instructions
Once the controller is correctly wired and powered, you can operate the motor using the following functions:
- Speed Control: Adjust the integrated potentiometer on the board to regulate motor speed. Alternatively, provide an external 0-5V analog or PWM signal to the speed regulation input.
- Direction Control (DIR): Use an external switch connected to the DIR interface and ground. A low-level signal (grounding the interface) will control the motor's direction (forward/reverse).
- Stop Control (STOP): Use an external switch connected to the STOP interface and ground. A low-level signal (grounding the interface) will stop the motor.
- Brake Control (BRAKE): Use an external switch providing a 5V high-level signal to the BRAKE interface. A high-level signal will activate the motor's braking function.

Figure 5: Key operational features of the ZS-X11H V1 controller.
6. Maintenance
- Keep the board clean and free from dust and moisture.
- Ensure proper ventilation around the heatsink to prevent overheating, especially during high-power operation.
- Regularly check all connections for tightness and signs of wear or corrosion.
- Avoid exposing the board to extreme temperatures or direct sunlight.
7. Troubleshooting
If you encounter issues, consider the following:
- Motor not starting or shaking: This is a common symptom of incorrect Hall signal wire sequencing. Refer to section 4.5 for debugging unclear interfaces and try all 6 Hall phase sequence combinations.
- Motor only rotates in one direction: This also indicates an incorrect Hall signal wire sequence. Re-check and adjust the Hall wiring as described in section 4.5.
- No response after power on: First, verify that the interface on the driver board matches your brushless motor interface. Then, check all power and signal connections.
- Risk of damage: When debugging, especially with unclear wiring, avoid high current and high voltage. Incorrect wiring under these conditions can damage the drive board.

Figure 6: Example installation of the ZS-X11H V1 controller in a custom e-bike build.
8. User Tips
- Many users report the controller works well for custom e-bike builds, such as with 36V batteries and Xiaomi motors.
- If the motor is not starting, ensure to check the motor itself before assuming the controller is at fault.
- The product is generally functional and works as intended when correctly wired.
9. Warranty and Support
For warranty information, technical support, or any product-related inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.
10. Additional Resources
A user manual in PDF format is available for download. This document may contain further detailed instructions and diagrams.
User manual (PDF): Download PDF