ZEFIORA V10

Contents

Zefiora V10 Electric Bicycle Instruction Manual

Model: V10 | Brand: ZEFIORA

Important Safety Information

WARNING: Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.

General Safety Notes

  • All users must read and understand this manual before their first use of the bike. Additional manuals for components used on the bike may also be provided and should be read before use in addition to this manual.
  • Ensure that you comprehend all instructions and safety notes/warnings.
  • Ensure the bike fits you properly before your first use. You may lose control or fall if your bike is too big or too small.
  • Always wear an approved bicycle helmet whenever using this product and ensure that all helmet manufacturer instructions are used for fit and care of your helmet. Failure to wear a helmet when riding may result in serious injury or death.
  • Ensure correct setup and tightening is performed on your bike before first using it and check the setup, tightening, and condition regularly.
  • It is your responsibility to familiarize yourself with the laws and requirements of operating this product in the area(s) where you ride.
  • Ensure the handlebar grips are undamaged and properly installed. Loose or damaged grips can cause you to lose control and fall.
  • Do not use this product with standard bike trailers, stands, electric bike racks or accessories that E-bikes has not tested for safety and compatibility and have verified as safe and compatible with the bike. Contact E-bikes to check if your equipment will work with the bike.
  • Off-road riding requires close attention, specific skills, and presents variable conditions and hazards which accompany the conditions. Wear appropriate safety gear and do not ride alone in remote areas. Check local rules and regulations if off-road E-bike riding is allowed.
  • Engaging in extreme riding is extremely dangerous and should be avoided. Although many articles/advertisements/catalogs depict extreme riding, this is not recommended nor permitted, and you can be seriously injured or killed if you perform extreme riding.
  • Bikes and bike parts have strength and integrity limitations and extreme riding should not be performed as it can damage bike components and/or cause or lead to dangerous riding situations in which you may be seriously injured or killed.
  • Failure to perform and confirm proper installation, compatibility, proper operation, or maintenance of any component or accessory can result in serious injury or death.
  • It is recommended to not ride at night if avoidable. Ride at night only if necessary.

Specific Safety Guidelines

  1. Always Wear A Helmet: Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements in your community. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and eye protection. Also check your state laws concerning other protective gear that may be required when riding the E-bike.
  2. Know Your E-bike: Your new E-bike incorporates many features and functions that have never been built into a bicycle before. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
  3. Ride Within Your Limits: Take it slow until you are familiar with the riding conditions that you encounter. Be especially careful in wet conditions as traction can be greatly reduced and brakes becoming less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue and inattention can significantly reduce your ability to make good judgment and safety.

Parts Identification

The Zefiora V10 electric bicycle consists of several key components. Familiarize yourself with these parts for proper operation and maintenance.

Front view of the Zefiora V10 electric bike, highlighting its main components.
Front view of the Zefiora V10 electric bike.

Key components include:

  • Bike Frame: The main structure of the bicycle.
  • Handlebar: For steering and control, equipped with controls for gears, lights, and horn.
  • Display: Shows operational data and settings.
  • LED Headlight: Front illumination for visibility.
  • Light: Rear light for visibility.
  • Seat: Rider's seating area.
  • Rear Rack: For carrying cargo.
  • Controller: Manages the electric system.
  • Rear Fender: Protects from splashes.
  • Bike Motor: Provides electric assistance.
  • Disc Brake Rotor: Part of the braking system.
  • Tire: 20x4.0 inch fat tires for various terrains.
  • Derailleur: For changing gears.
  • Battery: Power source for the electric motor and lights.
  • Crank: Connects pedals to the chainring.
  • Chain: Transmits power from pedals to the rear wheel.
  • Pedals: Footrests for propulsion.
  • Front Fork: Connects the front wheel to the frame and provides suspension.

Handlebar Controls:

  • Add Single-speed Button Downshift: For gear changes.
  • Power Button: To turn the bike's electrical system on/off.
  • Light Switch: To control the headlight and taillight.
  • Horn: For signaling.

Setup and Assembly Instructions

The following steps provide a general guide for assembling your Zefiora V10 electric bike. If you encounter difficulties, please contact customer service for assistance.

Step 1: Unpacking

Carefully unpack the e-bike from its carton and lay out all contents. Remove all packaging material protecting the bike frame and components. Please recycle packaging materials, especially cardboard and foam.

Step 2: Front Wheel Installation

  1. Insert the front wheel into the front fork.
  2. Next, insert the fork anti-spin hook plate and washer.
  3. Finally, insert the nut and tighten it securely.

Step 3: Kickstand, Handlebar, and Headlight Installation

  1. Kickstand: Remove the kickstand, then with the kickstand on the inside and the screws on the outside, tighten them clockwise using an M6 screwdriver.
  2. Handlebars: Loosen the handlebar mounting screws, place the handlebars on, and finally tighten the screws.
  3. Headlight: First, open the headlight mounting brackets on both sides, then install the black spacers. Adjust the front of the vehicle so that it is level with the tires, and tighten the bolts on both sides.
  4. Headlight Wiring: Locate the headlight wiring harness and the main wiring harness (which have arrow markings). Align them with the arrows and insert them into the harness, then confirm that they are securely plugged in.
  5. Front Fender: To install the front fender, remove the front fender and insert it from back to front, then tighten the screws. Secure the mounting brackets on both sides with screws.

Step 4: Adjusting Brake Tightness

Abnormal noise from brakes is often caused by thicker brake pads extending their lifespan, which can lead to friction. This is normal and should reduce after a few days of riding.

To adjust disc brakes to eliminate friction noise:

  1. Prepare tools and locate: Locate the disc brake caliper (the metal part that holds the brake disc). You will see two vertical screws on the caliper (usually an M6 Allen wrench is used). Have the appropriate tools ready.
  2. Loosen the screws: Use an M6 Allen wrench to slightly loosen these two screws (one to one and a half turns), allowing the clamp to move slightly left and right. Do not completely remove them.
  3. Alignment Position: Gently straighten the wheel with your hand, ensuring it's centered on the frame. Then, use your hand to slightly adjust the position of the brake caliper, moving it left and right. The goal is to align the brake disc exactly in the center of the two brake pads, with even clearance on both sides. While adjusting, gently rotate the wheel with your other hand, judging by the sound. The optimal position is when it rotates smoothly without any friction noise.
  4. Tighten: Keeping the caliper in the optimal position, tighten the two loosened screws alternately and in stages. Do not tighten one screw completely at once, as this can easily cause the position to shift again. After the screws are fully tightened, quickly rotate the wheel one last time to confirm that there are no abnormal noises. If slight friction persists, repeat steps 2-3.

Step 5: Rear Rack, Taillight, and Rear Seat Bag Installation

  1. Rear Rack: Locate the taillight, loosen its screws, and remove it. Unscrew all four screws on the back of the seat. Place the rear rack, align the holes, and tighten the screws on both sides.
  2. Taillight and Wiring: Locate the taillight wiring and tie it up with the cable ties that come with the vehicle.
  3. Rear Seat Bag: Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.

Operating Instructions

Operation Meter (Display)

The display provides essential information about your ride and allows you to adjust settings.

Display Elements:

  • Logo: Product logo.
  • Battery Level: Indicates remaining battery charge.
  • Total Distance (ODO): Total distance traveled by the bike.
  • Single Trip (TRIP): Distance traveled in the current trip.
  • Boost Icon: Indicates power assist level.
  • Headlight Icon: Indicates if headlights are on.
  • NFC Icon: (Functionality not detailed, likely for pairing or access).
  • Speed: Current riding speed.
  • Gear: Current gear selection.
  • Status Bar: General status indicators.

Basic Operations:

  1. Power On/Off: Press and hold the [Power button] for 2 seconds to turn the device on or off.
  2. Gear Shift: Press the [+ button] briefly to increase by one gear, and press the [- button] briefly to decrease by one gear.
  3. ODO/TRIP Data Display Toggle: Briefly press the [Power button] to switch between displaying ODO and TRIP data. The default display is TRIP.
  4. Implementation Model: Press and hold the [- button] to enter Implementation Model, and release the button to exit.

Setting Menu Operations

To access general settings, press and hold both the [+ button] and [- button] simultaneously. To exit without saving, press and hold the [- button] or remain inactive for 60 seconds.

Navigation:

  • Switch setting items: In the settings menu, press the [Power button] briefly to toggle between options.
  • Adjust setting parameters: Press the [+ button] or [- button] briefly to modify parameters.
  • Confirm: Press and hold the [Power button] to save changes and return to the previous level.

Available Settings:

  • SET 1: Wheel Diameter: Adjustable range: 16-29 inches (default: 26 inches). Not adjustable by default.
  • SET 2: Speed Limit: Select any value within the adjustable range (1-99), default: 25 km/h. Not adjustable by default.
  • SET 3: Unit: Options: Metric (KM/H) or Imperial (blank), default: KM/H.
  • SET 4: Screen Brightness: Adjustable range: 1-3 levels, default: Level 3.
  • SET 5: Auto Sleep Time: Adjustable range: 1-60 minutes, default: 10 minutes.
  • SET 6: Single Trip Auto Reset: Options: Set to "y" to clear the single trip mileage on startup, or set to "n" to retain the single trip mileage on startup.

Gears Operation

Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.

Important: Avoid shifting while standing up on the pedals or under load.

To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring that the chain is fully engaged in that gear before applying more pressure. For bicycles with 3 front chain rings, avoid "Cross Chaining" (when the chain is in the smallest cog in the rear combined with the inner or smallest chain ring in the front, or the largest cog in the rear and the outer or largest chain ring in the front). These gear positions put the chain at the most extreme angle and can cause premature wear to the drive train. Bicycles with 3 front chain rings have enough gear "overlaps" that these gears are not needed.

How to Use and Charge the Battery

The Zefiora V10 is powered by a Lithium Battery (48V).

Battery Removal and Check:

  1. Insert the battery key and turn it counterclockwise to turn on the battery switch.
  2. Remove the battery with both hands.
  3. To check battery level, turn on the red switch on the battery power button, then press the battery power button briefly.

Charging Procedure:

  1. Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
  2. With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger (round barrel connector) to the charging port on the side of the battery.
  3. Plug the charger into the outlet. Connect the charger input plug (100-240V AC) to the power outlet. Charging should initiate and will be indicated by the LED charge status light on the charger turning red.
  4. Unplug the charger from the outlet, then the charging port. Once fully charged (indicated by the charging indicator light turning green), unplug the charger from the wall outlet first and proceed to remove the charger.

Charging Attention:

  • Before charging, make sure the charger light faces upwards.
  • Full charge normally takes 3-7 hours.
  • Charge the battery in a clean and safe place and do not overcharge.
  • Red light on charger means the battery is charging.
  • Green light on charger means the battery is fully charged.

Battery Charging Information:

  • Always charge your battery in temperatures between 50 °F - 77 °F (10 °C - 25 °C) and ensure the battery and charger are not damaged before initiating charge.
  • If you notice anything unusual while charging, discontinue charging and use of the bike and contact for help.
  • Do not charge the battery for more than 12 hours at a time or leave a charging battery unattended.
  • Always charge in dry, indoor locations away from direct sunlight, dirt, or debris. Charge in a clear area away from potential to trip on the charging cords or for damage to occur to the bike, battery, or charging equipment while parked and/or charging.
  • Do not use with the charger inverted, which can inhibit cooling and reduce charger lifespan.
  • The battery should be recharged after each use, so it is ready to go the full range per charge next ride. There is no memory effect, so charging the battery after short rides will not cause damage.
  • Ensure the battery is turned off whenever it is being removed or off the bike. Avoid damaging the exposed connector terminals and keep them clear of debris.
  • Do not touch the "+" and terminal contacts on the bottom of the battery when the battery is removed from the bike.

Maintenance

Basic Bike Care

To ensure safe riding conditions, you must properly maintain your e-bike. Follow these basic guidelines and see a certified, reputable bike mechanic at regular intervals to ensure your bike is safe for use and fun to ride.

  1. Batteries: Properly maintain batteries by keeping them fully charged when between uses of up to two weeks apart. Refer to the Long-Term Battery Storage section (if available in the full PDF manual) for information on storing the battery for longer than two weeks between rides.
  2. Water Exposure: Never immerse or submerge the bike or any components in water or liquid as the electrical system may be damaged.
  3. Wiring and Connectors: Periodically check wiring and connectors to ensure there is no damage and that the connectors are secure.
  4. Cleaning: To clean, wipe the frame with a damp cloth. If needed, apply a mild non-corrosive detergent mixture to the damp cloth and wipe the frame. Dry by wiping with a clean, dry cloth.
  5. Storage: Store under shelter; avoid leaving the bike in the rain or exposed to corrosive materials. If exposed to rain, dry your bike afterwards and apply anti-rust treatment to chain and other unpainted steel surfaces.
  6. Coastal Areas: Riding on the beach or in coastal areas exposes your bike to salt, which is very corrosive. Wipe down your bike frequently and wipe or spray all unpainted parts with anti-rust treatment. Damage from corrosion is not covered under warranty, so special care should be given to extend the life of your bike when used in coastal areas or areas with salty air or water.
  7. Bearings: If the hub and bottom bracket bearings have been submerged in water or liquid, they should be taken out and re-greased. This will prevent accelerated bearing deterioration.
  8. Paint: If the paint has become scratched or chipped in the metal, use touch-up paint to prevent rust. Clear nail polish can also be used as a preventative measure.
  9. General: Regularly clean and lubricate all moving parts, tighten components, and adjust as required.

Pre-Riding Safety Checklist

Before every ride, and after every 25-45 miles, it is advised to follow this pre-riding safety checklist:

Safety CheckBasic Steps
Brakes
  • Ensure front and rear brakes work properly.
  • Check brake pads for wear and ensure they are not over-worn.
  • Ensure brake pads are correctly positioned in relation to the rims.
  • Ensure brake control cables are lubricated, correctly adjusted, and display no obvious wear.
  • Ensure brake control levers are lubricated and tightly secured to the handlebars.
  • Test brake levers are firm and that brake, motor cutoff functions, and brake light are functioning properly.
Wheels and Tires
  • Ensure tires are inflated to within the recommended limits displayed on the tire sidewalls and holding air.
  • Ensure tires have good tread, have no bulges or excessive wear, and are free from any other damage.
  • Ensure rims run true and have no obvious wobbles, dents, or kinks.
  • Ensure all wheel spokes are tight and not broken.
  • Check axle nuts and front wheel quick release skewer is correctly tensioned, fully closed, and secure position.
Steering
  • Ensure handlebar and stem are correctly adjusted and tightened and allow proper steering.
  • Ensure the handlebar is set correctly in relation to the forks and the direction of travel.
Chain
  • Ensure the chain is oiled, clean, and runs smoothly.
  • Extra care is required in wet, salty/otherwise corrosive, or dusty conditions.
Bearings
  • Ensure all bearings are lubricated, run freely, and display no excess movement grinding, or rattling.
  • Check headset, wheel bearings, pedal bearings, and bottom bracket bearings.
Cranks and Pedals
  • Ensure pedals are securely tightened to the cranks.
  • Ensure the cranks are securely tightened and are not bent.
Derailleurs
  • Check that the derailleur is adjusted and functioning properly.
  • Ensure shifter and brake levers are attached to the handlebar securely.
  • Ensure all brake and shift cables are properly lubricated.
Frame, Fork, and Seat
  • Check that the frame and fork are not bent or broken.
  • If either frame or fork are bent or broken, they should be replaced.
  • Check that the seat is adjusted properly and seat post quick release lever is securely tightened.
Motor Drive Assembly
  • Ensure hub motor is spinning smoothly and motor bearings are in good working order.
  • Ensure all power cables running to hub motor are secured and undamaged.
  • Make sure the hub motor axle bolts are secured and all torque arms and torque washers are in place.
Battery
  • Ensure battery is charged before use.
  • Ensure there is no damage to battery.
  • Lock battery to frame and check to see that it is secured.
  • Charge and store bike and battery in a dry location, between 50°F-77°F.
  • Let bike dry completely for using again.
Electrical Cables
  • Look over connectors to make sure they are fully seated, free from debris or moisture.
  • Check cables and cable housing for obvious signs of damage.
  • Ensure headlight, taillight, and brake light are functioning adjusted properly, and unobstructed.
Accessories
  • Ensure all reflectors are properly fitted and not obscured.
  • Ensure all other fittings on bike are properly secured and functioning.
  • Inspect helmet and other safety gear for signs of damage.
  • Ensure rider is wearing helmet and other required riding safety gear.
  • Ensure mounting hardware is properly secured if fitted with rear rack.
  • Ensure taillight and taillight power wire are properly secured if fitted with rear rack.
  • Ensure fender mounting hardware is properly secured if fitted with fenders.
  • Ensure there are no cracks or holes in fenders if fitted with fenders.

Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 miles (80-160km), and bolted connections can loosen. Always have a certified, reputable mechanic perform on your E-bike after this initial break-in period. Regular inspections and tune-ups are particularly important for ensuring that your bike remains safe and fun to ride.

Troubleshooting

This section provides solutions to common issues you might encounter with your Zefiora V10 electric bike. If the problem persists, please contact customer service.

SymptomsPossible CausesMost Common Solutions
The bike does not work
  • Insufficient battery power
  • Faulty connections
  • Battery not fully seated in tray
  • Improper turn on sequence
  • Brakes are applied
  • Charge the battery
  • Clean and repair connectors
  • Install battery correctly
  • Turn on bike with proper sequence
  • Disengage brakes
Irregular acceleration and/or reduced top speed
  • Insufficient battery power
  • Loose or damaged throttle
  • Misaligned or damaged magnet ring
  • Charge or replace battery
  • Replace throttle
  • Align or replace magnet ring
The motor does not respond when the bike is powered on
  • Loose wiring
  • Loose throttle
  • Loose motor plug wire
  • Repair and or reconnect
  • Tighten throttle
  • Secure motor plug wire
Reduced range
  • Low tire pressure
  • Low or faulty battery
  • Driving with too many hills, headwind, braking, and/or excessive load
  • Battery discharged for long period of time without regular charges, aged, damaged, or unbalanced
  • Brakes rubbing
  • Adjust tire pressure
  • Check connections or charge battery
  • Assist with pedals or adjust route
  • Balance the battery: contact tech support if range decline persists
  • Adjust the brakes
The battery will not charge
  • Charger not well connected
  • Charger damaged
  • Adjust the connections
  • Replace charger
Wheel or motor makes strange noises
  • Loose wheel spokes or rim
  • Loose motor wiring
  • Tighten, repair, or replace
  • Reconnect motor

Fault Code Comparison Table

When a fault occurs, the red fault indicator on the instrument panel lights up. The instrument interface will flash the fault information as a reminder and display the "Error" prompt.

No.Data StatusMeaningInstrument Display
10x21Controller Fault21
20x22Throttle Fault22
30x23Motor Phase Loss23
40x24Hall Sensor Fault23
50x25Undervoltage Protection25
60x26Brake Lever Fault26
70x30Communication Fault30

Specifications

The Zefiora V10 electric bicycle is designed for robust performance across various terrains, including mountainous and snowy areas.

AttributeValue
Model NumberV10
Brand NameZEFIORA
CertificationCE
Vehicle Size168 x 69 x 110 cm
Packing Size138 × 26 × 84 cm
ColorBlack
Frame MaterialAluminum alloy (also listed as Steel in some data, Aluminum alloy is more common for e-bikes)
Net Weight37 kg (81.57lb) / 36.5KG (80.47lb)
Gross Weight46kg (101.41lb)
ChargerAC-DC 54.6V 2A, Input: 100-240V AC, Connector: DC 5.5×2.1 mm
Brake SystemFront and rear disc brake
Tire Size20x4.0 inch
Rated Passenger CapacityOne Seat
StyleStandard Type
Max Speed>50km/h
Range per Power> 60 km
Wattage> 500w (2000W peak output)
Power Supply / SourceLithium Battery
Voltage48V
FoldedNo
Motor TypeBrushless
OriginMainland China

User Tips

  • Initial Break-in: After the first 50-100 miles (80-160km), have a certified mechanic check all bolted connections and cables as they may stretch and loosen.
  • Regular Cleaning: Keep your bike clean, especially after riding in wet or salty conditions, to prevent corrosion and ensure longevity.
  • Battery Care: Always recharge the battery after each use to ensure it's ready for your next ride and to maintain battery health. Avoid leaving the battery fully discharged for extended periods.
  • Tire Pressure: Regularly check and maintain correct tire pressure for optimal range and riding comfort.
  • Brake Adjustment: If you hear a 'sizzling' sound from the brakes, it might be normal during the initial break-in period. If it persists, follow the brake adjustment steps in the assembly section or consult a professional.
  • Visibility: Always wear bright, reflective clothing and ensure all lights and reflectors are clean and functional, especially when riding in low light conditions.

Warranty and Support

For detailed warranty information, please refer to the official user manual PDF. This document provides a general overview.

Official User Manual (PDF): For a comprehensive guide, including detailed diagrams and specific instructions, please refer to the Zefiora V10 Electric Bicycle User Manual (PDF).

Customer Service: If you have any questions, require assistance with installation, or encounter issues not covered in this manual, please feel free to contact us. We aim to reply and solve problems within 24 hours.

Email: ebikesservice@outlook.com

Compliance and Disclaimer

Disclaimer: ⚠️Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

The Zefiora V10 electric bicycle is CE certified, indicating compliance with European safety, health, and environmental protection requirements.

Certificate of Conformity for Electric Bicycle Model Z10
Certificate of Conformity for Electric Bicycle (Model Z10, similar to V10).
Verification of Conformity and Test Reports for Electric Bicycle Models Z10/V10
Verification of Conformity and Test Reports for Electric Bicycle (Models Z10/V10).
UL 2849 Test Reports for Electrical Systems for E-bikes
UL 2849 Test Reports for Electrical Systems for E-bikes.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.