1. Important Safety Information
WARNING:
Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.
1.1 Always Wear A Helmet
Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements in your community. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and eye protection. Also check your state laws concerning other protective gear that may be required when riding the E-bike.
1.2 Know Your E-bike
Your new E-bike incorporates many features and functions that have never been built into a bicycle before. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
1.3 Ride Within Your Limits
Take it slow until you are familiar with the riding conditions that you encounter. Be especially careful in wet conditions as traction can be greatly reduced and brakes becoming less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue and inattention can significantly reduce your ability to make good judgement and safely.

Image: Safety information highlighting helmet use and e-bike display.
1.4 Disclaimer
⚠️Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
2. Parts Identification
Familiarize yourself with the various components of your Zefiora V12 Electric Bicycle.

Image: Detailed diagram identifying key parts of the Zefiora V12 Electric Bicycle, including the bike frame, seat, handlebars, LED headlight, disc brake rotor, motor, battery, pedals, and more.
2.1 Key Components
- Bike Frame: The main structure of the bicycle.
- Handlebar: For steering and control.
- LED Headlight: Provides illumination for night riding.
- Disc Brake Rotor: Part of the braking system.
- Battery: Power source for the electric motor.
- Motor: Provides electric assistance.
- Pedals: For traditional cycling.
- Seat: For rider comfort.
- Rear Rack: For carrying cargo.
- Controller: Manages the e-bike's electrical system.
- Front/Rear Fender: Protects from splashes.
- Derailleur: For gear shifting.
- Tires: 20x4.0 inch fat tires for all-terrain use.
2.2 Handlebar Controls

Image: Detailed view of the e-bike's intuitive controls, including the display screen, speaker button, light button, power button, upshift/downshift buttons, brake levers, 7-speed thumb shifter, and thumb twist shifter.
3. Assembly Instructions
The following assembly steps are a general guide to assist in the assembly of your bike. For detailed visual guidance, please refer to the official installation video and the user manual PDF.
Video: Zefiora V12 Electric Bicycle Model overview and installation guide.
3.1 Unpacking and Initial Setup
- Unpack the e-bike from the carton and carefully lay out all contents. Remove all packaging material protecting the bike frame and components.

Image: E-bike components laid out after unpacking, ready for assembly.
3.2 Front Wheel Installation
- Install the front wheel: Insert the front wheel into the front fork.
- Next, insert the fork anti-spin hook plate and washer, and finally insert the nut and tighten it.
3.3 Kickstand and Handlebar Installation

Image: Visual guide for installing the kickstand and handlebars, showing screw locations and tightening steps.
- To install the kickstand, remove the kickstand, then with the kickstand on the inside and the screws on the outside, tighten them clockwise using an M6 screwdriver.
- To install the handlebars, loosen the handlebar mounting screws, place the handlebars on, and finally tighten the screws.
3.4 Headlight and Fender Installation

Image: Instructions for securing the front fender and connecting the headlight wiring harness, emphasizing arrow alignment for proper connection.
- Adjust the front of the vehicle so that it is level with the tires, and tighten the bolts on both sides.
- For headlight installation, first open the headlight mounting brackets on both sides, then install the black spacers.
- Then tighten the screws on both sides.
- Locate the headlight wiring harness and the main wiring harness, which have arrow markings. Align them with the arrows and insert them into the harness, then confirm that they are securely plugged in.
- To install the front fender, remove the front fender and insert it from back to front, then tighten the screws.
- Then, secure the mounting brackets on both sides with screws.
3.5 Rear Rack Installation (if applicable)
Adding a rear rack depends on whether you have one or not.

Image: Guide for installing the rear rack, showing how to remove the taillight, unscrew bolts, and secure the rack.
- Locate the taillight, loosen the taillight screws, and remove the taillight.
- Unscrew all four screws on the back.
- Then place the rear rack in the rear shelf, align the holes, and tighten the screws on both sides.
3.6 Taillight and Rear Seat Bag Installation

Image: Instructions for securing the taillight wiring with cable ties and attaching the rear seat bag to the fender.
- Locate the taillight wiring and tie it up with the cable ties that come with the vehicle.
- Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.
4. Operation
4.1 Operation Meter
The LCD display provides essential riding information.

Image: Diagram of the e-bike's operation meter, showing speed display, battery level, mileage, gear indication, and status bar.
- Power On/Off: Press and hold the [Power button] for 2 seconds to turn the device on or off.
- Gear Shift: Press the [+ button] briefly to increase by one gear, and press the [- button] briefly to decrease by one gear.
- ODO/TRIP Data Display Toggle: Briefly press the [Power button] to switch between displaying ODO (total distance) and TRIP (single trip distance) data. The default display is TRIP.
- Implementation Model: Press and hold the [- button] to enter Implementation Model, and release the button to exit.
4.2 Setting Menu Operations
To access general settings: Press and hold both the [+ button] and [- button] simultaneously to enter the general settings menu.
- Switch setting items: In the settings menu, press the [Power button] briefly to toggle between options.
- Adjust setting parameters: Press the [+ button] or [- button] briefly to modify parameters.
- Confirm: Press and hold the [Power button] to save changes and return to the previous level.
- Return to home page: Press and hold the [- button] to exit without saving and return to the main interface, or remain inactive on the page for 60 seconds to automatically exit the settings menu and return to the home page.
Setting Menu Options:
- SET 1: Wheel Diameter (Adjustable range: 16-29 inches, default: 26 inches. Not adjustable by default.)
- SET 2: Speed Limit (Select any value within the adjustable range (1-99), default: 25 km/h. Not adjustable by default.)
- SET 3: Unit (Options: Metric (KM/H) or Imperial (blank), default: KM/H.)
- SET 4: Screen Brightness (Adjustable range: 1-3 levels, default: Level 3.)
- SET 5: Auto Sleep Time (Adjustable range: 1-60 minutes, default: 10 minutes.)
- SET 6: Single Trip Auto Reset (Options: Set to "y" to clear the single trip mileage on startup, or set to "n" to retain the single trip mileage on startup.)
4.3 Gears Operation
Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.

Image: Diagram illustrating gear operation, highlighting combinations to avoid for optimal chain health.
- Avoid shifting while standing up on the pedals or under load.
- To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring that the chain is fully engaged in that gear before applying more pressure on the pedals.
- For bicycles with 3 front chain rings, avoid "Cross Chaining," which is the position when the chain is in the smallest cog in the rear combined with the inner or smallest chain ring in the front, or the largest cog in the rear and the outer or largest chain ring in the front. These gear positions put the chain at the most extreme angle and can cause premature wear to the drivetrain.
4.4 Riding Modes
The Zefiora V12 offers multiple riding modes to suit various terrains and preferences, eliminating charging anxiety.

Image: Diagram showcasing the different riding modes: Walk Assist Mode, Normal Bike Mode, Pedal Assist Mode, and Pure Electric Mode, demonstrated in a snowy landscape.
- Walk Assist Mode: Your get-home guarantee, providing light assistance for walking alongside the bike.
- Normal Bike Mode: Pure pedaling, offering an unlimited range without electric assistance.
- Pedal Assist Mode (PAS Mode): More you pedal, farther you go. The motor provides assistance based on your pedaling input.
- Pure Electric Mode: Pure power, zero effort. The motor provides full power without pedaling.
5. Battery Usage and Charging
5.1 How to Use the Battery

Image: Instructions for inserting the battery key, turning on the battery switch, removing the battery, and checking the battery level using the red switch.
- Insert the battery key and turn it counterclockwise to turn on the battery switch, then remove the battery with both hands.
- Turn on the red switch on the battery power button, then press the battery power button briefly to see the battery level.
5.2 Charging Procedure
- Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
- With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger (round barrel connector) to the charging port on the side of the battery.
- Plug the charger into the outlet, then the charging port. Connect the charger input plug (100-240-volt plug) to the power outlet. Charging should initiate and will be indicated by the LED charge status light on the charger turning red.
- Unplug the charger from the outlet, then the charging port. Once fully charged, indicated by the charging indicator light turning green, unplug the charger from the wall outlet first and proceed to remove the charger.

Image: Battery charger showing red light for charging and green light for full charge.
5.3 Battery Charging Information
- Always charge your battery in temperatures between 50 °F - 77 °F (10 °C - 25 °C) and ensure the battery and charger are not damaged before initiating charge.
- If you notice anything unusual while charging, please discontinue charging and use of the bike and contact for help.
- Charging the battery fully normally takes 3-7 hours. In rare cases, it may take longer to allow the battery management system to balance the battery, particularly when the bike is new or after long periods of storage.
- The battery can be recharged on or off the bike.
- Do not charge the battery for more than 12 hours at a time or leave a charging battery unattended.
- Ensure the lights face upwards when using the charger. The charge indicator lights on the charger will stay red while the battery charges and one will turn green when charge is complete.
- Always charge in dry, indoor locations away from direct sunlight, dirt, or debris. Charge in a clear area away from potential to trip on the charging cords or for damage to occur to the bike, battery, or charging equipment while parked and/or charging. Do not use with the charger inverted, which can inhibit cooling and reduce charger lifespan.
- The battery should be recharged after every use, so it is ready to go the full range per charge next ride. There is no memory effect, so charging the battery after short rides will not cause damage.
- Ensure the battery is turned off whenever it is being removed or off the bike. Avoid damaging the exposed connector terminals and keep them clear of debris.
- Do not touch the "+" and terminal contacts on the bottom of the battery when the battery is removed from the bike.
6. Maintenance
6.1 Basic Bike Care
To ensure safe riding conditions, you must properly maintain your e-bike. Follow these basic guidelines and see a certified, reputable bike mechanic at regular intervals to ensure your bike is safe for use and fun to ride.
- Properly maintain batteries by keeping them fully charged when between uses of up to two weeks apart. See Long-Term Battery Storage section of manual for information on storing the battery for longer than two weeks between rides.
- Never immerse or submerge the bike or any components in water or liquid as the electrical system may be damaged.
- Periodically check wiring and connectors to ensure there is no damage and the connectors are secure.
- To clean, wipe the frame with a damp cloth. If needed, apply a mild non-corrosive detergent mixture to the damp cloth and wipe the frame. Dry by wiping with a clean, dry cloth.
- Store under shelter; avoid leaving the bike in the rain or exposed to corrosive materials. If exposed to rain, dry your bike afterwards and apply anti-rust treatment to chain and other unpainted steel surfaces.
- Riding on the beach or in coastal areas exposes your bike to salt, which is very corrosive. Wipe down your bike frequently and wipe or spray all unpainted parts with anti-rust treatment. Damage from corrosion is not covered under warranty so special care should be given to extend the life of your bike when used in coastal areas or areas with salty air or water.
- If the hub and bottom bracket bearings have been submerged in water or liquid, they should be taken out and re-greased. This will prevent accelerated bearing deterioration.
- If the paint has become scratched or chipped in the metal, use touch up paint to prevent rust. Clear nail polish can also be used as a preventative measure.
- Regularly clean and lubricate all moving parts, tighten components, and adjust as required.
6.2 Pre-Riding Safety Checklist
Before every ride, and after every 25-45 miles, we advise following this pre-riding safety checklist:
| Safety Check | Basic Steps |
|---|---|
| 1. Brakes |
|
| 2. Wheels and Tires |
|
| 3. Steering |
|
| 4. Chain |
|
| 5. Bearings |
|
| 6. Cranks and Pedals |
|
| 7. Derailleurs |
|
| 8. Frame, Fork, and Seat |
|
| 9. Motor Drive Assembly |
|
| 10. Battery |
|
| 11. Electrical Cables |
|
| 12. Accessories |
|
Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 miles (80-160km), and bolted connections can loosen. Always have a certified, reputable mechanic perform on your E-bike after this initial break-in period. Regular inspections and tune-ups are particularly important for ensuring that your bike remains safe and fun to ride.
6.3 Brake Adjustment
If your bicycle's disc brakes are rubbing against the disc (making a "sizzling" sound), follow these steps for fine-tuning:

Image: Visual guide for adjusting disc brakes, showing the cable locknut and caliper screws.
- Prepare tools and locate: Locate the disc brake caliper (the metal part that holds the brake disc). You will see two vertical screws on the caliper (usually an M6 Allen wrench is used).
- Loosen the screws: Use an M6 Allen wrench to slightly loosen these two screws. Note: Only loosen them by one to one and a half turns, allowing the clamp to move slightly left and right. Do not completely remove them.
- Alignment Position: Gently straighten the wheel with your hand, ensuring it's centered on the frame. Now, use your hand to slightly adjust the position of the brake caliper, moving it left and right. Your goal is to align the brake disc exactly in the center of the two brake pads, with even clearance on both sides. While adjusting, gently rotate the wheel with your other hand, judging by the sound. The optimal position is when it rotates smoothly without any friction noise.
- Tighten screws: Keeping the caliper in the optimal position, tighten the two loosened screws alternately and in stages. Do not tighten one screw completely at once, as this can easily cause the position to shift again.
- After the screws are fully tightened, quickly rotate the wheel one last time to confirm that there are no abnormal noises. If there is still slight friction, repeat steps 2-3.
7. Troubleshooting
This section provides solutions to common issues you might encounter with your Zefiora V12 Electric Bicycle.
| Symptoms | Possible Causes | Most Common Solutions |
|---|---|---|
| The bike does not work |
|
|
| Irregular acceleration and/or reduced top speed |
|
|
| The motor does not respond when the bike is powered on |
|
|
| Reduced range |
|
|
| The battery will not charge |
|
|
| Wheel or motor makes strange noises |
|
|
7.1 Fault Display Codes
When a fault occurs, the red fault indicator on the instrument panel lights up. The instrument interface will flash the fault information as a reminder and display the "Error" prompt.
| No. | Data Status | Meaning | Instrument Display |
|---|---|---|---|
| 1 | 0x21 | Controller Fault | 21 |
| 2 | 0x22 | Throttle Fault | 22 |
| 3 | 0x23 | Motor Phase Loss | 23 |
| 4 | 0x24 | Hall Sensor Fault | 23 |
| 5 | 0x25 | Undervoltage Protection | 25 |
| 6 | 0x26 | Brake Lever Fault | 26 |
| 7 | 0x30 | Communication Fault | 30 |
8. Specifications
Detailed specifications for the Zefiora V12 Electric Bicycle.
| Attribute | Value |
|---|---|
| Model Number | V12 |
| Brand Name | ZEFIORA |
| Certification | CE |
| Rated Passenger Capacity | One Seat |
| Style | Standard Type |
| Max Speed | >50km/h |
| Range per Power | > 60 km |
| Wattage | > 500w (Peak 2000W) |
| Power Supply | Lithium battery |
| Voltage | 48V |
| Power Source | Lithium battery |
| Origin | Mainland China |
| Folded | No |
| Motor Type | Brushless |
| Wheel Size | 20“ |
| Frame Material | Aluminum alloy |
| High-concerned chemical | None |
| Vehicle Size | 168 x 69 x 110 cm |
| Packing Size | 138 × 26 × 84 cm |
| Color | Black |
| Net Weight | 37 kg (81.57lb) / 36.5KG (80.47lb) |
| Gross Weight | 46kg (101.41lb) |
| Charger | AC-DC 54.6V 2A, Input: 100-240V AC, Connector: DC 5.5×2.1 mm |
| Brake System | Front and rear disc brake |
| Tire Size | 20x4.0 inch |

Image: Diagram showing recommended height (5'24"-6'56"), load capacity (330LBS), and key dimensions of the Zefiora V12 Electric Bicycle.
8.1 Certifications

Image: Compilation of various compliance certificates including CE, UL, and RoHS, indicating adherence to safety and environmental standards.
9. User Tips
Here are some general tips to enhance your riding experience and prolong the life of your Zefiora V12 Electric Bicycle:
- Regular Tire Pressure Checks: Maintain optimal tire pressure for better range, comfort, and safety.
- Battery Care: Always charge your battery fully after each ride, even short ones, to maintain battery health. Store the battery in a cool, dry place.
- Smooth Shifting: Ease off the pedals slightly when shifting gears to prevent chain wear and ensure smooth transitions.
- Terrain Awareness: While the fat tires are versatile, be mindful of extreme conditions. Adjust your speed and riding mode according to the terrain.
- Visibility: Always use headlights and taillights, especially in low-light conditions, and consider wearing reflective clothing for maximum visibility.
- Secure Components: Periodically check all bolts and connections, especially after the initial break-in period, to ensure everything is securely fastened.
10. Warranty and Support
For detailed information regarding warranty coverage, return policies, and other service commitments, please refer to the official user manual PDF and contact customer support.
10.1 Official User Manual (PDF)
A comprehensive user manual in PDF format is available for download. This document contains detailed instructions, safety guidelines, and specifications that complement this HTML manual.
Reference: Zefiora V12 Electric Bicycle User Manual (PDF)
10.2 Customer Support
If you have any questions, require assistance with installation, or encounter any issues not covered in this manual, please feel free to contact us. We aim to reply and solve your problem within 24 hours.
Email: ebikesservice@outlook.com
10.3 Service Commitments
- Fast Delivery: We strive for prompt delivery.
- Security & Privacy: We do not share your personal details with any third parties without your consent and protect your privacy.
- Sustainability: We are committed to sustainable practices.