1. Introduction
The FOCUS Vesa 830A is an advanced Industrial Inkjet UV Label Printer designed for high-precision, efficient, and eco-friendly label production. It caters to the global demand for printing on non-coating plastic labels, offering seamless performance across a wide range of materials. This manual provides essential information for the safe and effective operation and maintenance of your Vesa 830A printer.
Key features include intelligent scanning calibration, a high-precision piezo-electric printhead, a closed-loop UV curing ink system, multi-language interfaces, and cloud-based data management for flexible customization and rapid delivery. Balancing productivity with sustainability, it empowers global users to dominate short-run printing and personalized labeling markets.
2. Setup Guide
Before operating the FOCUS Vesa 830A, ensure proper installation and setup. Follow these steps carefully:
- Unpacking and Placement: Carefully unpack the printer and its components. Place the printer on a stable, level surface in an environment with controlled temperature (15-30°C) and humidity (40-80%). Ensure adequate space around the printer for operation and maintenance.
- Power Connection: Connect the printer to a stable AC 110-220V power source.
- Media Loading:
The printer features a self-tension control unwinder and rewinder system. Load your label media roll onto the unwinder spindle. Ensure the media is properly aligned and secured. The built-in material tension adjustment function will help maintain smooth feeding and accurate positioning during printing.
Image: Self-tension control unwinder and rewinder mechanism, ensuring smooth media feeding.
The system supports media rolls with a maximum diameter of φ350mm and a width of 300mm.
Image: Demonstrates loading a large media roll onto the printer.
- Ink System Setup: The printer utilizes a Focus Inc. WIPCS white ink process system. Ensure the UV ink cartridges (C/M/Y/K/W) are correctly installed. The system includes a high-quality white ink circulation peristaltic pump for extended service life.
- Print Head Initialization: The automatic head maintenance cap system will perform an initial cleaning and moisturizing cycle. Follow the on-screen prompts or refer to the control panel for status.
- Software Installation: Install the necessary printing software on your computer. Ensure your computer meets the minimum system requirements (Windows® 7/10/11/94 bit, Intel® Core™ i5 or higher, 8GB RAM, 1GB HDD space, 100GB for image storage).
- Connectivity: Connect the printer to your computer via Ethernet cable.
3. Operating Instructions
The Vesa 830A is designed for user-friendly operation. Here are the general steps for printing:
- Prepare Your Design: Create or load your label design using compatible software. Ensure the design resolution and color profile are optimized for UV printing.
- Load Media: As described in the Setup Guide, ensure your label media roll is correctly loaded and tensioned.
- Adjust Vacuum Adsorption: The printer features a vacuum adsorption print table. Adjust the suction as needed to prevent the printing film from bending or scraping the print heads, especially for thinner materials.
- Select Print Settings:
- Print Mode: Choose between 4Pass, 6Pass, or 8Pass depending on desired speed and quality.
- Ink Colors: The printer uses C/M/Y/K/W UV inks. It supports White+Color synchronous printing, allowing for vibrant prints on dark and transparent plastic media.
- Resolution: Select your desired print resolution (e.g., 1200 dpi, 2400 DPI).
- Start Printing: Initiate the print job from your computer. The multi-function printing control panel will display the printing process in real-time, making operation convenient.
- Die-Cutting (Optional): The printer supports integrated die-cutting, waste removal, and take-up. This can be done simultaneously with printing or as a post-printing step. A CCD camera ensures high-precision die-cutting.
Image: Close-up of the vacuum adsorption print table, showing the perforated surface.
Image: The Vesa 830A printer actively printing labels with the unwinder and rewinder system.
Image: LED UV curing lights active during the printing process, ensuring immediate ink drying.
Image: Integrated system for die-cutting, waste removal, and automatic take-up of finished labels.
Print Samples
The Vesa 830A can print on a variety of materials, including:
These examples demonstrate the versatility of the Vesa 830A for various label applications, including food packaging, bags, bottles, and more.
Image: Examples of products (bottles, bags) that can utilize labels printed by the Vesa 830A.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your FOCUS Vesa 830A printer.
- Print Head Cleaning: The automatic head maintenance cap system facilitates smooth and efficient print head cleaning and moisturizing. Perform routine cleaning cycles as recommended by the printer software or when print quality degrades.
- Ink System Check: Regularly monitor ink levels and ensure the white ink circulation system (WIPCS) is functioning correctly. The peristaltic pump is designed for extended service life.
- General Cleaning: Keep the printer's exterior and internal components free from dust and ink residue. Use a soft, lint-free cloth.
- Consumables: Replace UV lamps and other consumables as needed. Refer to the printer's software or indicators for replacement schedules.
Image: The automatic cap station designed for efficient print head cleaning and moisturizing.
Image: Close-up of the Focus Inc. WIPCS white ink process system, highlighting the peristaltic pump.
5. Troubleshooting
This section addresses common issues you might encounter. For more complex problems, please contact technical support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Poor Print Quality (streaks, faded colors) | Clogged print nozzles, low ink levels, incorrect print settings. | Perform a print head cleaning cycle. Check ink levels and replace if low. Verify print settings (resolution, pass mode) match media type. |
| Media Feeding Issues (jams, misalignment) | Improper media loading, incorrect tension, debris in paper path. | Re-load media, ensuring it's aligned and tensioned correctly. Inspect the media path for any obstructions. Adjust vacuum adsorption if media is curling. |
| Printer Not Responding | Loose power cable, connectivity issue, software error. | Check power connections. Verify Ethernet cable connection. Restart the printer and computer. Ensure printer drivers and software are up-to-date. |
| Inaccurate Die-Cutting | CCD camera calibration needed, incorrect cutting parameters. | Calibrate the CCD camera. Review and adjust die-cutting parameters in the software. |
6. Technical Specifications
Below are the detailed technical specifications for the FOCUS Vesa 830A Industrial Inkjet UV Label Printer:
| Feature | Specification |
|---|---|
| Maximum Printing Area | Width 300mm * Length no limit (11.8" * unlimited) |
| Head Type | Epson I3200 (2 pcs) |
| Print Head Nozzle Amount | 6400 (2 pcs print head) |
| Print Head Technology | EPSON MEMS PRECISIONCORE micro piezo printing technology |
| Jetting Frequency | 21.6-43.2KHz |
| Drop Volume | 3.5-12.5pl (Variable data printing, multi drop) 2-4 Grayscale |
| Print Resolution (dots per inch) | 720-1200dpi, 720-2400dpi, 1200-2400dpi, Uni-direction/Bi-direction |
| Print Speed | 4Pass: 12-17㎡/hour; 6Pass: 10-12㎡/hour; 8Pass: 8-10㎡/hour (4Pass: 12-17m/min; 6Pass: 10-12m/min; 8Pass: 8-10m/min) |
| Print Head Maintain Technology | Auto keep wet cap station system & Clean flushing during printing and idle |
| Max Media Width | 300mm |
| Maximum External Diameter | φ350mm |
| Roller Inner Diameter | φ75mm, φ40mm, φ25mm |
| Film Feeding | Automatic electronic take up Roller |
| Film Take Up | Automatic electronic take up Roller |
| Vacuum Power | 200W |
| Vacuum System | Full flatbed vacuum absorption |
| Vacuum Control | Electronic button switch control |
| Media Type | Roll type film, paper, Canvas, leather, PP, BOPP, POPP, PE, PET, PVC, metal foil, PET, Glossy, Matt, Non-coated paper, etc. |
| Ink Process Unit | Automatic white ink stirring system |
| Ink Curing Unit | 405nm UV-LED lamp * 2pcs, 200W |
| Ink Type | UV Ink |
| Ink Colors | C/M/Y/K/W |
| Ink Tank Capacity | 220ml per color; 500ml for white ink tank. Refillable. |
| Dimensions (L*W*H) | Printer: 34.5(L) * 23.6(W) * 18.9(H) in. (876 * 600 * 481mm) Main printer. Package: 54.3(L) * 38.9(W) * 28.4(H) in. (1380 * 990 * 720 mm) All. |
| Net Weight | 251 lb (114kg) Printer only, 112lb (51kg) Unwinder+Rewinder |
| Operating Voltage | AC 110-220V |
| Power Supply | Power Mode |
| Working Power | Printer 350W, Unwinder+Rewinder 120W |
| Environment Temperature | 59 to 86 °F (15 to 30 °C) |
| Humidity | 40 to 80 % |
| Connectivity | Ethernet cable |
| Acoustic Noise Level | 75 dB (A) or less |
| Included Items | Print cable, Cleaning kit, USB drive with manuals and installation videos |
System Requirements
| Component | Requirement |
|---|---|
| Operating System | Windows® 7/10/11 (64 bit) |
| CPU | Recommend Intel® Core™ i5, 2.5 GHz or more |
| RAM | 8 GB or more |
| Graphics Card | A resolution of 1152 * 864 with 16 bit color or higher |
| HDD | Install space 1 GB or more, Working space 100 GB |
*Note: Technical instructions subject to change without notice.
Image: Comprehensive table of technical specifications and a diagram illustrating the machine's dimensions.
7. Warranty and Support
The FOCUS Vesa 830A printer comes with a 1-Year Warranty from the date of purchase, covering manufacturing defects under normal use conditions.
For technical assistance, troubleshooting, or warranty claims, please contact FOCUS Inc. support:
- WhatsApp: +86 19727388387
- Email: maoyishunda@gmail.com
Please have your model number (Vesa 830A) and purchase details ready when contacting support.