User Manual

1. Product Information

This manual provides instructions for the installation and operation of the TOP-MAX LED Front Side Corner Lights, designed as direct replacements for your Dodge Charger's original side marker lamps.

• Product Name: Car Side Marker Light
• Brand: TOP-MAX
• Item Type: Fender Marker / Side Marker
• Part Numbers: 4806219AD (Left), 4806218AD (Right)
• Origin: Mainland China

Figure 1: TOP-MAX LED Front Side Corner Lights

2. Manufacturer & EU Representative Information

Manufacturer:

Guangzhou Kuxiong Shi Trading Co., Ltd
No. 503, Building 3, Courtyard 2, Zhongquantang Road, Industrial Avenue, Haizhu District, Guangzhou City
Phone: +86-18814180059
Email: tingting26181@outlook.com

EU Authorized Representative:

Sea&Mew Consulting GmbH
Mittenhuber Straße 4, 92318 Neumarkt
Phone: +4915224685061
Email: Compliance.EU@outlook.com

3. Compliance Information

This product conforms to relevant European Union directives and regulations.

4. Safety & Warnings

▲ WARNING: Before installing or replacing the side lights, the vehicle's power switch must be turned off, the engine must be turned off, and if necessary, the negative terminal of the battery must be disconnected. This prevents circuit short circuits, electrical leakage, electric shock, and damage to the vehicle's electrical system.

• Always wear appropriate personal protective equipment (e.g., safety glasses, gloves) during installation.
• Ensure all connections are secure and properly insulated to prevent electrical hazards.
• Do not modify the product in any way, as this may void the warranty and create safety risks.

5. Setup & Installation Instructions

Follow these steps carefully for proper installation:

Step 1: Pre-Installation Test

1. Before permanent installation, connect the wiring harness of the new side marker lights to your vehicle's electrical system.
2. Test all functions (daytime running, turn signal, reverse, etc.) to ensure they are functioning properly before proceeding with full installation.

Step 2: Positioning and Mounting

3. Clean the intended installation position thoroughly (e.g., the top of the wheel arch, fender) to ensure good adhesion.
4. Determine the exact paste position and mark it with a marker pen for accuracy.
5. Carefully heat the backing adhesive on the new side marker light (a heat gun or hairdryer on low setting can be used).
6. Align the light with your marks and paste it firmly onto the vehicle surface.

Figure 2: Example of LED Side Marker Lights installed on a Dodge Charger

Step 3: Wiring

7. Hide Wiring: Route and hide the wiring harness along existing gaps in the vehicle body (e.g., inner side of wheel arches, side skirts, door rubber strips). Secure the harness using zip ties to prevent movement or damage.
8. Protect Wires: If wires need to pass through any body sheet metal holes, install a rubber sleeve (grommet) to protect the wire insulation from abrasion.
9. Power Supply Connection:
   • Connect the RED wire to the ACC (Accessory) power supply. A common point is the cigarette lighter fuse.
   • Connect the BLACK wire to a reliable ground point on the vehicle's metal body.
10. Turn Signal Connection:
    • Connect the YELLOW wire (or other designated turn signal wire) in parallel to the vehicle's existing left/right turn signal wire. Use a non-breaking clip for this connection.
    • Install a 1-3A fuse in series with this connection for protection.
11. Reverse Signal Connection (if applicable):
    • Connect the WHITE wire in parallel to the vehicle's reverse light signal line.
    • Install an appropriate fuse in series with this connection.

Step 4: Insulation and Fixing

12. Ensure all wiring points are properly insulated. Wrap connections with heat shrink tubing or high-quality electrical tape (velvet tape is recommended for automotive applications).
13. Secure the entire wiring harness to the original vehicle wiring harness using zip ties to prevent any loosening or rattling.

Step 5: Final Testing

14. After completing the installation, retest all functions of the side marker lights (daytime running, turn signals, reverse) to ensure they are working correctly.
15. Visually inspect all wiring and connections for any signs of electrical leakage or loose contacts.

6. Operating Instructions

Your TOP-MAX LED Front Side Marker Lights offer enhanced visibility and styling. Depending on the model purchased, they may feature:

• Constant Light: Provides a steady amber illumination as a side marker.
• Dynamic Light (Sequential): Provides a sequential amber illumination for turn signals, where LEDs light up in a flowing pattern.

The lights will operate in conjunction with your vehicle's existing lighting system (e.g., turn signals activate when you engage the turn signal lever).

Figure 3: Illustration of Sequential Dynamic Light function

7. Maintenance

• Cleaning: Clean the light lenses periodically with a soft cloth and mild automotive cleaner to maintain clarity and brightness. Avoid abrasive cleaners.
• Inspection: Periodically check the lights for any signs of damage, loose connections, or moisture ingress.
• Wiring: Ensure wiring remains secure and insulated. Re-secure any loose zip ties or re-insulate exposed wires as needed.

8. Troubleshooting

• Lights Not Working:
  • Check all wiring connections for proper contact and security.
  • Verify that the fuses (both for ACC and turn signal/reverse) are intact and not blown.
  • Ensure the power and ground connections are correctly made.
• Lights Flickering:
  • Inspect for any loose wiring connections or poor ground contact.
  • Check for any intermittent power supply issues.
• One Light Not Working:
  • Check the specific wiring for that light, including its power and ground connections.
  • Ensure the T10 plug is fully seated.

If problems persist after troubleshooting, please contact customer support.

9. Specifications

Figure 4: Product Dimensions

10. User Tips

• For the best and most secure installation, ensure the mounting surface is completely dry and free of grease or wax before applying the adhesive.
• Double-check all electrical connections before reassembling any vehicle panels to save time on potential re-work.
• Consider using dielectric grease on electrical connectors to prevent corrosion and ensure a long-lasting connection.

11. Warranty & Support

For warranty information, technical support, or any inquiries regarding your TOP-MAX LED Front Side Marker Lights, please contact the seller or manufacturer directly using the details below:

Manufacturer Contact:

Email: tingting26181@outlook.com

EU Authorized Representative Contact:

Email: Compliance.EU@outlook.com

A full PDF version of this manual may be available for download from the seller's product page or by contacting support.