1. Introduction
Thank you for purchasing the Godox iT32 iFlash Camera Flash. This modular lighting system is designed for ultimate versatility and efficiency, offering full TTL and HSS support across various camera brands. The iT32 flash body, when paired with different X5 versions, seamlessly adapts to Canon, Nikon, Sony, Fujifilm, and OM System cameras. The X5 functions as both a hotshoe mount and a wireless trigger, enabling instant transitions between on-camera and off-camera use, and complex multi-light setups. Its magnetic modularity, cross-brand compatibility, and integrated Godox 2.4GHz wireless system empower photographers to shape light effortlessly, anytime and anywhere.
This product is professional photographic equipment and should be operated by professional personnel only. All transport protective materials and packaging must be removed before use.
2. Important Safety Instructions
Please read and follow these safety precautions carefully to prevent serious injury, damage to the product, or other property damage.
- Carefully read and fully understand this instruction manual before use and strictly follow all safety instructions.
- High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.
- This product is a professional lighting fixture; children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture to prevent collisions or unauthorized use.
- This is not an ordinary lighting fixture and must not be used for general illumination. Individuals with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
- Exercise extreme caution when using it. Do not touch high-temperature parts such as flash tubes and surrounding metal components to avoid burns.
- Do not point the flash directly at the eyes (especially baby's eyes) under any circumstances, as this could impair vision. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
- If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for replacement.
- Do not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use.
- Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching internal electronic components and getting an electric shock.
- This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. Install in a ventilated and dry location, avoiding rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it.
- Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by authorized personnel.
- Before storing, ensure the device is completely cooled down and the power cord (if any) is unplugged. Store in the protective case or a ventilated dry location.
- Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
- Do not use or store this device in potentially explosive environments.
- Do not use accessories not approved by Godox, as this may cause fire, electric shock, or personal injury.
- Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
- Some products are equipped with protective covers that must be removed before use.
- This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check the official website for the latest instruction manual and product updates.
3. Main Features
- Separated Triggering: Remove X5 from iT32 and insert it into the camera hot shoe mount. The camera flash can then be wirelessly controlled (X5 is sold separately).
- Convenient Operation: Intuitive interaction via a colorful touch screen and simplified traditional buttons.
- Professional and Portable: Auto flash, manual flash, multi flash, HSS, second-curtain sync, and FEC functions within a lightweight body of merely 169g (without X5).
- 2.4G Wireless System: Built-in Godox 2.4G wireless X system ensures stable signal transmission and anti-interference capabilities in complex environments.
- TTL Compatibility: Perfectly supports TTL auto flash to simplify the shooting procedure by automatically adjusting flash output.
- Precise Lighting Control: Power adjustment range from 1/128 to 1/1, with ±1/3 increment fine-tuning.
- Efficient Power Supply: 7.2V/900mAh lithium battery supports USB-C charging, 1.5s recycle time at 1/1 step, and 510 full-power flashes at full battery level.
- LED Modeling Lamp: Supports brightness adjustment from level 1 to level 10.
- Firmware Upgrade: Firmware is updated regularly to be compatible with the latest camera models and ensure optimal performance.
Note: The fastest recycle time is based on Godox laboratory test results. After high-intensity continuous flashes, the system will automatically extend the recycle time for safe heat dissipation, which is a normal protection mechanism. Once the device cools down, it can return to peak recycle speed.
Product demonstration video showcasing the iT32 flash and X5 trigger in various shooting scenarios, highlighting features like flexible flash head, touchscreen control, and wireless capabilities.
4. Name of Parts
4.1. Flash Body

Diagram of the Godox iT32 Flash Body, illustrating its main components.
- Flash Head
- Wide-angle Diffuser (Transparent, inside the flash head)
- Catchlight Panel (White, inside the flash head)
- LED Modeling Lamp
- Photocell Sensor
- Sync Cord Jack
- USB-C Port (Charging/firmware upgrade)
- Touch Screen
- MENU Button
- SET Button
- < < / > > Button
- Select Dial
- Select Dial Alignment Marker
4.2. TTL Wireless Flash Trigger X5 (Sold Separately)

Diagram of the Godox X5 TTL Wireless Flash Trigger, showing its components.
- Indicator
- < −/> Button
- < +/M > Button
- Hot Shoe Locking Ring
- Hot Shoe
Note: The appearances and contacts of hot shoes vary in different models.
5. What's in the Box

Image showing the standard contents included with the Godox iT32 flash.
- Flash Body (iT32) ×1
- USB-C Charging Cable ×1
- Magnetic Mini Stand ×1
- Diffuser ×1
- Magnetic Color Filter (1/2 orange) ×1
- Magnetic Color Filter (1/1 orange) ×1
- Storage Bag ×1
- Instruction Manual ×1
6. Separately Sold Accessories
Enhance your photography with these optional Godox accessories:
- TTL Wireless Flash Trigger X5 series (e.g., X5 S/X5 C/X5 N/X5 F/X5 O)
- Flash trigger X2T series
- Flash trigger XProII series
- Flash trigger X3 series
- Magnetic Accessory Kit MA02 (includes various color filters and diffusers)

MA02 Magnetic Attachment with various color filters, compatible with iT30Pro/iT32.
7. Setup
7.1. Installing the Flash Trigger (X5)
Align the flash trigger (X5) with the bottom of the iT32 flash body in the direction shown in the diagram. Place it in, and the flash will automatically absorb it magnetically. Once installed, the <C> icon in the menu interface will light up.

Visual guide for attaching the X5 trigger to the iT32 flash.
7.2. Installing the Diffuser
Align the protruding side of the diffuser with the <iT32> logo side of the flash body. Then, insert it firmly until fully seated.

Illustration of how to correctly install the diffuser on the iT32 flash.
7.3. Mounting on the Camera
Rotate the hot shoe locking ring of the flash trigger clockwise to the top. Insert the trigger into the hot shoe mount of the camera. Then, rotate the hot shoe locking ring anticlockwise until it is firmly locked.

Visual guide for securely mounting the iT32 flash with X5 trigger onto a camera.
Note: Please make sure the flash and camera are powered off before installing and disassembling.
8. Operating Instructions
8.1. Power Switch
- Power On: Press and hold the < < / > > button until the icon appears. Then, slide up on the screen or rotate up the select dial to unlock. The device will turn off automatically if it stays locked for 6 seconds after power on (this function can be turned off in bootup settings, then press and hold the < < / > > button can directly power on the device).
- Power Off: Press and hold the < < / > > button until the screen blacks out.
The flash trigger X5 does not have a power on/off function. Its status can be checked via the indicator:
| Indicator | Description |
|---|---|
| Flash green | Unconnected to camera in TTL mode |
| Constant on green | Connected to camera in TTL mode |
| Flash orange | Unconnected to camera in M mode |
| Constant on orange | Connected to camera in M mode |
| Flash red slowly | Low battery level |
| Light off | Sleep mode, press any button to wake |
8.2. Battery Level Indication
iT32: Check the battery level indication on the panel to see the remaining battery level.
| Battery Level Indication | Meaning |
|---|---|
| 3 grids | Full |
| 2 grids | Middle |
| 1 grid | Low |
| Blank grid | Lower battery, please recharge it. |
| Blinking | The battery level is going to be used out, and the flash is not functional in this status. |
Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for a long period.
X5: Install X5 to iT32. Slide the screen top-down to enter the menu interface, find the <C> icon, and click to check the model and battery level of the flash trigger.
Check via the Indicator: When X5 and iT32 are unconnected, press and hold the < −/> button of the flash trigger until the indicator turns red. Then check the battery level by observing the number of red flashes from the indicator (one flash indicates low battery, four flashes indicate full charge, and so on).
8.3. Charging Instructions
- iT32: It takes approximately 1 hour 10 minutes to fully charge the camera flash with the USB-C charging cable, and provides approximately 510 full power flashes at full battery level.
- X5: It can be charged after connected to iT32. It triggers once every 10 seconds at full battery level, for about 4000 times. The charging output port of iT32 is not universal and only supports charging X5 C/N/S/F/O.
8.4. Flash Modes
8.4.1. Wi-Off Mode (With Flash Trigger X5)
Touch Screen: Slide the screen top-down to enter the menu interface, click the < < / > > icon to choose < > and enter Wi-Off mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < < / > > icon, then press the SET button to choose < > and enter Wi-Off mode.
TTL: TTL Auto Flash
In TTL mode, the camera's metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed.
Touch Screen: Slide the screen top-down to enter the menu interface, click the <TTL/M/Multi> icon to choose <TTL> and enter TTL auto flash mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <TTL> and enter TTL auto flash mode.
FEC Amount Adjustment: Press the <−>/<+> icon or rotate the select dial in the main interface to adjust the FEC amount from -3.0 to +3.0 with ±1/3 increment each step, or directly pull the progress bar to achieve quick adjustment.
Note: When the shutter is fully pressed, the flash will fire a pre-flash that the camera will use to calculate exposure and flash output the instant before the photo is taken.
M: Manual Flash
S1 and S2 photocell functions are available in M mode, and the flash output is adjustable. To obtain a correct flash exposure, use a handheld flash meter to determine the required flash output.
Touch Screen: Slide the screen top-down to enter the menu interface, click the <TTL/M/Multi> icon to choose <M> and enter M manual flash mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <M> and enter M manual flash mode.
Output Power Adjustment: Press the <−>/<+> icon or rotate the select dial in the main interface to adjust the power from 1/128 to 1/1 with ±1/3 increment each step, or directly pull the progress bar to achieve quick adjustment.
S1/S2 Photocell
The photocell sensor will enter standby mode to continuously monitor changes in ambient light levels after the photocell triggering is turned on.
- S1 Photocell Unit: With this function, the flash will fire synchronously when the main flash fires, producing the same effect as wireless triggers. This helps create multiple lighting effects.
- S2 Photocell Unit (pre-flash): This is useful when cameras have a pre-flash function. With this function, the flash will ignore a single "pre-flash" from the main flash and will only fire in response to the second, actual flash from the main unit.
Note: Enter the setting interface to switch between S1/S2 photocell or turn off this function.
Multi: Stroboscopic Flash
In multi flash mode, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph. You can set the number of flashes, flash frequency (number of flashes per second, expressed as Hz), and flash output.
- Number of flashes: 1-100
- Flash frequency: 1-100
- Flash output range: 1/128-1/4
Touch Screen: Slide the screen top-down to enter the menu interface, click the <TTL/M/Multi> icon to choose <Multi> and enter multi flash mode. Press the <−>/<+> icon or directly pull the progress bar to adjust the flash power. Press the times/frequency icon on the upper right corner to enter the number of flashes and flash frequency adjustment interface, slide the numbers up or down to adjust the respective parameters.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <Multi> and enter multi flash mode. Directly rotate the select dial to adjust the output power. Press the SET button to choose the times/frequency icon on the upper right corner, then rotate the select dial to adjust the respective parameters.
Calculating the Shutter Speed in Multi Flash Mode
During multi flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.
Number of Flashes ÷ Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the flash frequency is 5Hz, the shutter speed should be at least 2 seconds.
Note:
- Multi flash is most effective with a highly reflective subject against a dark background.
- Using a tripod and TTL flash trigger is recommended.
- A flash output of 1/1 and 1/2 cannot be set for multi flash.
- Multi flash can also be used with "BULB" mode.
- Multi flash mode cannot be set in high-speed sync, second-curtain sync, and first-curtain sync modes.
Maximum Time of Consecutive Flashes
| Flash Output | Number of Flashes (Hz) | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6-7 | 8-9 | 10 | |
| 1/4 | 8 | 6 | 4 | 3 | 3 | 2 | 2 | 2 |
| 1/8 | 14 | 14 | 12 | 10 | 8 | 6 | 5 | 4 |
| 1/16 | 30 | 30 | 30 | 20 | 20 | 20 | 10 | 10 |
| 1/32 | 60 | 60 | 60 | 50 | 50 | 40 | 30 | 20 |
| 1/64 | 90 | 90 | 90 | 80 | 80 | 70 | 60 | 50 |
| 1/128 | 100 | 100 | 100 | 100 | 100 | 90 | 80 | 70 |
Note: To avoid overheating and deteriorating the flash head, do not use multi flash more than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15 minutes. If you try to use the multi flash more than 10 times in succession, the firing might stop automatically to protect the flash head. If this happens, allow at least 15 minutes' rest for the camera flash.
8.4.2. Sender Mode (With Flash Trigger X5)
Touch Screen: Slide the screen top-down to enter the menu interface, click the < < / > > icon to choose < > and enter sender mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < < / > > icon, then press the SET button to choose < > and enter sender mode.
Gr: Sender Group
The flash mode, output power, and FEC amount of the receiver unit can be individually adjusted in Gr mode.
- Groups: M, A, B, C (iT32+X5 S/N/F/O); A, B, C, D (iT32+X5 C)
- Flash Modes: TTL auto flash mode/M manual flash mode
Touch Screen: Slide the screen top-down to enter the menu interface, click the <Gr/Multi> icon to choose <Gr>. The flash power and FEC amount are adjustable by clicking the <−>/<+> icon, or quickly adjustable by pulling the progress bar. Press and hold the group box to switch among M (manual) flash, TTL auto flash, and OFF.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <Gr/Multi> icon, then press the SET button to choose <Gr>. Press the MENU button to enter the main interface, rotate the select dial to choose a certain group. Then press the SET button to enter the group settings, and rotate the select dial to adjust the flash power and FEC amount. Press and hold the SET button to switch among M (manual) flash, TTL auto flash, and OFF.
Multi: Stroboscopic Flash
The number of flashes, flash frequency, and output power of the receiver unit can be universally adjusted in multi mode.
Touch Screen: Slide the screen top-down to enter the menu interface, click the <Gr/Multi> icon to choose <Multi>, then slide the screen up to enter the main interface. Press the group icon on the upper left corner to choose a certain group. Press the <−>/<+> icon or directly pull the progress bar to adjust the flash power. Press the times/frequency icon on the upper right corner to enter the number of flashes and flash frequency adjustment interface, slide the numbers up or down to adjust the respective parameters.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <Multi>. Press the MENU button to enter the main interface, directly rotate the select dial to adjust the output power. Press the SET button and rotate the select dial to choose among number of flashes, flash frequency, group, and output power, then press the SET button and rotate the select dial to adjust the respective parameters.
Note: The details of which please refer to the section Wi-Off mode → multi: stroboscopic flash above.
8.4.3. Receiver Mode (With Flash Trigger X5)
As a receiver unit, iT32+X5 are controllable by other Godox flash triggers with 2.4G wireless function.
Touch Screen: Slide the screen top-down to enter the menu interface, click the < < / > > icon to choose < > and enter sender mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < < / > > icon, then press the SET button to choose < > and enter sender mode.
TTL: TTL Auto Flash
Touch Screen: Slide the screen top-down to enter the menu interface, click the <TTL/M/Multi> icon to choose <TTL> and enter TTL auto flash mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <TTL> and enter TTL auto flash mode.
Group Selection: Press the group icon, or press the SET button and rotate the select dial to choose a certain group.
M: Manual Flash
Touch Screen: Slide the screen top-down to enter the menu interface, click the <TTL/M/Multi> icon to choose <M> and enter M manual flash mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <M> and enter M manual flash mode.
Group Selection: Press the group icon, or press the SET button and rotate the select dial to choose a certain group.
Output Power Adjustment: Press the <−>/<+> icon or rotate the select dial to adjust the power from 1/128 to 1/1 with ±1/3 increment each step, or directly pull the progress bar to achieve quick adjustment.
Multi: Stroboscopic Flash
Touch Screen: Slide the screen top-down to enter the menu interface, click the <TTL/M/Multi> icon to choose <Multi>, then slide the screen up to enter the main interface. Press the group icon on the upper left corner to choose a certain group. Press the <−>/<+> icon or directly pull the progress bar to adjust the flash power. Press the times/frequency icon on the upper right corner to enter the number of flashes and flash frequency adjustment interface, slide the numbers up or down to adjust the respective parameters.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the <TTL/M/Multi> icon, then press the SET button to choose <Multi>. Press the MENU button to enter the main interface, directly rotate the select dial to adjust the output power. Press the SET button and rotate the select dial to choose among number of flashes, flash frequency, group, and output power, then press the SET button and rotate the select dial to adjust the respective parameters.
Note: The details of which please refer to the section Wi-Off mode → multi: stroboscopic flash above.
8.4.4. Receiver Mode (Separated Triggering)
Remove X5 from iT32 then insert it into a camera hot shoe. iT32 will switch to receiver mode automatically, enabling off-camera wireless triggering via the camera shutter.
Flash Mode Switch: Press and hold the < +/M > button of the flash trigger to wirelessly control the flash to switch between TTL auto flash mode and M manual flash mode. The indicator of the flash trigger will flash green in TTL auto flash mode, and flash orange in M manual flash mode.
Output Power Adjustment: Adjust the flash to M manual flash mode, press the <−/>/<+/M> button of the flash trigger to adjust the power from 1/128 to 1/1 with ±1/3 increment each step.
FEC Amount Adjustment: Adjust the flash to TTL auto flash mode, press the <−/>/<+/M> button of the flash trigger to adjust the FEC amount from -3.0 to +3.0 with ±1/3 increment each step.
Sync Triggering Godox Flashes
When iT32 and X5 are separated, X5 can also sync trigger other Godox flashes.
Example (AD100ProII):
- Remove X5 from iT32; iT32 will switch to receiver mode automatically.
- Power off the camera, insert X5 into the camera hot shoe, and power it on.
- Set AD100ProII: Press the MENU button to enter the menu interface, rotate and press the SET dial to select and enter wireless settings, set the group, channel, and ID to be the same as iT32.
- Press the camera shutter to sync trigger iT32 and AD100PROII.
Note: Group A supports triggering, output power, and FEC amount adjustment; other groups only support triggering.
8.5. Sync Modes
8.5.1. High-speed Sync (HSS)
High-speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.
Touch Screen: Slide the screen top-down to enter the menu interface, click the < < / > > icon to choose < > and enter high-speed sync mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < < / > > icon, then press the SET button to switch to < > and enter high-speed sync mode.
Note:
- The minimal flash power is 1/16 in HSS mode.
- Choose HSS mode in camera settings for iT32+X5 F.
- When using a Nikon camera with iT32+X5 N, HSS is on by default in high-speed camera shutter, while HSS is off in low-speed shutter.
8.5.2. Second-curtain Sync
With a slow shutter speed and second-curtain sync, you can create a light trail following the subject. The flash fires right before the shutter closes.
Touch Screen: Slide the screen top-down to enter the menu interface, click the < < / > > icon to choose < > and enter second-curtain sync mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < < / > > icon, then press the SET button to switch to < > and enter second-curtain sync mode.
Note:
- For iT32+X5 S: Choose <REAR> flash mode in the settings of Sony camera.
- For iT32+X5 F: Choose MENU>Flash Light Function Setting>REAR < > flash mode on Fujifilm cameras.
- For iT32+X5 N: Press < > button on Nikon camera, rotate the dial until < > appears on the control panel to enter rear-curtain sync mode, set the camera shutter.
- For iT32+X5 O: Press <OK> button on OM SYSTEM camera or <MENU> button on Panasonic camera to enter rear curtain sync mode setting. When the < > appears on the display, set the camera shutter.
8.5.3. First-curtain Sync
With a first-curtain sync, you can create a light trail leading the subject. The flash fires when the shutter starts.
Touch Screen: Slide the screen top-down to enter the menu interface, click the < < / > > icon to choose < > and enter first-curtain sync mode.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < < / > > icon, then press the SET button to switch to < > and enter first-curtain sync mode.
Note: Please refer to the second-curtain sync section above for the settings of different cameras.
8.6. Modeling Lamp
Touch Screen: Slide the screen top-down to enter the menu interface, click the < > icon to enter modeling lamp settings, in which you can turn on or off the modeling lamp. Pull the progress bar to adjust its brightness from level 1 to level 10.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < > icon, then press the SET button to enter modeling lamp settings. Press the SET button again to turn on or off the modeling lamp. Rotate the select dial to choose the progress bar, then press the SET button and rotate the select dial to adjust its brightness from level 1 to level 10.
Inter Function: In the modeling lamp interface, press the inter switch, or rotate the select dial to choose inter switch and press the SET button, to turn on or off the inter function.
Note: Turn on the inter function, the modeling lamp will automatically turn off when flashing.
8.7. Screen Lock
Touch Screen: Slide the screen top-down to enter the menu interface, click the < > icon to turn on the screen lock function. Press and hold the SET button for 2 seconds to unlock.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < > icon, then press the SET button to turn on the screen lock function. Press and hold the SET button for 2 seconds to unlock.
8.8. Wireless Settings
8.8.1. Channel Settings
If there are other wireless flash systems nearby, you can change the wireless channels to prevent signal interference. The wireless channels (01-32) of the sender unit and the receiver unit(s) must be set to the same.
Touch Screen: Slide the "Channel" box to choose your desired channel.
Buttons and Select Dial: Rotate the select dial to choose "Channel" box, then press the SET button to enter channel settings, rotate the select dial and press the SET button to choose your desired channel.
8.8.2. ID Settings
Change the wireless ID to avoid interference, as it can only be triggered after the wireless IDs (OFF/01-99) of the sender unit and the receiver unit are set to the same.
Touch Screen: Slide the "ID" box to turn off the ID, or choose your desired ID.
Buttons and Select Dial: Rotate the select dial to choose "ID" box, then press the SET button to enter ID settings, rotate the select dial and press the SET button to choose your desired ID.
8.8.3. Wireless Sync
The wireless sync function helps the sender and receiver to quickly set the same channel and ID.
Note: Wireless sync function is only available in sender mode and receiver mode.
Receiver Wireless Sync
Preconditions:
- Set iT32+X5 to sender mode (refer to sender mode section).
- Assume a retro camera flash (e.g., Lux Master) as the receiver.
Touch Screen: Click the "SYNC" icon on both iT32 and Lux Master.
Buttons and Select Dial: Rotate the select dial on iT32 to choose "SYNC" icon, then press the SET button. Rotate the select dial on Lux Master to choose "SYNC" icon, then press the SET button.
Sender Wireless Sync
Preconditions:
- Set iT32+X5 to receiver mode (refer to receiver mode section).
- Assume a flash trigger (e.g., X3) as the sender.
Touch Screen: Click the "SYNC" icon on both iT32 and X3.
Buttons and Select Dial: Rotate the select dial on iT32 to choose "SYNC" icon, then press the SET button. Rotate the select dial on X3 to choose "SYNC" icon, then press the select dial.
iT32+X5 Wireless Sync
When both the sender unit and receiver unit are iT32+X5, wireless sync is also available.
8.9. Custom Function Settings
Touch Screen: Slide the screen top-down to enter the menu interface, click the < > icon to enter custom function settings interface.
Buttons and Select Dial: Press the MENU button to enter the menu interface, rotate the select dial to choose the < > icon, then press the SET button to enter custom function settings interface.
Users can set the parameters of the following custom functions:
| Icon | Function | Options | Description |
|---|---|---|---|
| Trigger Dist | 0-30m | For extremely close distance triggering in a range from 0 to 30m (in sender mode) | |
| 1-100m | For far distance triggering in a range from 1m to 100m (in sender mode) | ||
| Sender Flash (only available in iT32+X5 C) | On | Sender flash on | |
| Off | Sender flash off | ||
| S | Photocell | OFF | Turn off photocell |
| S1 | The flash will fire synchronously when the main flash fires, only available in M manual flash mode. | ||
| S2 | The flash will ignore a single "pre-flash" from the main flash and will only fire in response to the second, actual flash from the main flash, only available in M manual flash mode. | ||
| TCM | TCM | On | Flash value of TTL mode can be converted to the power value of M mode (only available in Wi-Off mode) |
| Off | Turn off this function | ||
| Standby | On | Automatically standby after the set time (90 seconds) of idle use, and auto power off after 8 hours of idle use. | |
| Off | Do not automatically standby after the set time (90 seconds) of idle use. | ||
| Auto Off | Off | Turn off auto power off function | |
| 30 min | The flash will automatically shut down after 30 minutes of idle use. | ||
| 60 min | The flash will automatically shut down after 60 minutes of idle use. | ||
| 90 min | The flash will automatically shut down after 90 minutes of idle use. | ||
| Screen Standby | 30 sec | Screen standby after 30 seconds of idle use. | |
| 1 min | Screen standby after 1 minute of idle use. | ||
| 2 min | Screen standby after 2 minutes of idle use. | ||
| 3 min | Screen standby after 3 minutes of idle use. | ||
| Screen Brightness | Pull the progress bar to adjust the screen brightness | ||
| New Agreement (only available in iT32+X5 S) | On | The agreement is on by default. | |
| Off | Turn off when the camera is not compatible with the flash trigger. | ||
| Bootup Settings | Bootup Animation | When activated, it displays the "Godox & Honor of Kings" animation (available in Honor of Kings edition only). | |
| Unlock at Bootup | Slide the screen or rotate the dial to unlock when activated | ||
| Language | Simplified Chinese | Simplified Chinese system | |
| English | English system | ||
| Factory Reset | Apply | Factory reset | |
| Cancel | Cancel factory reset | ||
| Device Info | Display the device model and firmware version, download the latest firmware from the official website for update. |
8.10. Wireless Flash Shooting (2.4G Wireless Transmission)
This chapter explains how to perform wireless multiple shooting with 2.4G wireless transmission by using iT32+X5 as the sender unit and Godox flashes with 2.4G wireless receiving function as the receiver unit.
As a sender unit, iT32+X5 can control various receiver units with the Godox wireless X system such as AD100Pro II, AD200Pro II, AD600Pro II, AD600BM II, iT32, iT30Pro, V100, V480, and Lux Master.
Note:
- The channel, group, and ID of the sender and receiver units should be set to the same. Refer to the wireless settings section above for details.
- The listed models are popular ones controllable by iT32+X5. Refer to the official website for more controllable models.
8.10.1. TTL: Wireless Multiple Flash Shooting in TTL Auto Flash Mode
Set the flash groups (A, B, and C) of iT32+X5 (sender unit) as <TTL>, either with the same or different FEB values. There is no need to set the receiver units, and they will perform wireless multiple flash shooting in auto flash.

Diagram illustrating a TTL Wireless Multiple Flash Shooting setup with iT32+X5 as sender and multiple receiver units. Transmission distance is about 100m.
Note: iT32+X5 C has group D.
8.10.2. M: Wireless Multiple Flash Shooting in M Manual Flash Mode
Set the flash groups (A, B, and C) of iT32+X5 (sender unit) as <M>, either with the same or different flash output power. There is no need to set the receiver units, and they will perform wireless multiple flash shooting by following the sender.

Diagram illustrating an M Manual Flash Shooting setup with iT32+X5 as sender and multiple receiver units. Transmission distance is about 100m.
Note: iT32+X5 C has group D.
8.10.3. Multi: Wireless Multiple Flash Shooting in Multi Flash Mode
Set the iT32+X5 (sender unit) to multi flash mode. There is no need to set the receiver units (A, B, and C), and they will perform wireless multiple flash shooting with the sender unit. Set the flash output value, number of flashes, and flash frequency on the sender unit. The receiver units will follow the sender.

Diagram illustrating a Multi Flash Shooting setup with iT32+X5 as sender and multiple receiver units. Transmission distance is about 100m.
Note: iT32+X5 C has group D.
8.11. Control with the Camera's Menu (only available in iT32+X5 C)
If the camera flash is attached to an EOS camera which has a camera control function, the flash can be controlled using the camera's menu screen. The available settings vary depending on the flash mode, wireless flash function settings, and other conditions.
Setting Camera Flash Functions:
- Select <Flash control> or <External Speedlite control>.
- Select <Flash function settings> or <External func. setting>.
- The setting screen and items displayed vary depending on the camera.
Note:
- To clear all custom function settings, you can enter the [Clear settings] in step 2 and select [Clear all Speedlite C.Fn's] or [Clear ext. flash C.Fn set.].
- If flash exposure compensation has already been set with the camera flash, flash exposure compensation cannot be set with the camera. To set it with the camera, the camera flash's flash exposure compensation must be set to zero.
- If any flash custom functions and flash settings other than flash exposure compensation have been set by both the camera and the flash, the latest settings will take effect.
8.12. Global Shutter Sync Shooting (only available in iT32+X5 S)
By using a combination of iT32+X5 S and a camera equipped with a global shutter image sensor, flash photography can be synchronized with the entire range of shutter speeds available on the camera, enabling more effective flash exposures than conventional high-speed sync photography (HSS).
- When iT32+X5 S is used in TTL auto flash mode with a global shutter camera, the flash will be synchronized properly at both low and high shutter speeds. Compared to a non-global shutter camera, with a global shutter camera, the HSS flash time is shorter (about 2-5 milliseconds), the recycle time is faster, and the camera can take more shots.
- When iT32+X5 S is used in M (manual) flash mode and you want to use single pulse flash (not HSS) in high-speed shutter (with a shutter speed faster than 1/600), you can adjust the camera's flash delay time to match the exposure time, so that you can shoot with a more appropriate amount of light. Compared to HSS mode, this mode has a better flash index with the same power.
Flash timing settings: Camera Menu → (Exposure/Color) → [Flash] → [Flash Timing Setting] → [On] → Set the flash timing to the desired value.
ADJ flash timing settings menu:
- On: Adjusts the flash timing manually (0 microseconds to 1000 microseconds).
- Off: Does not adjust the flash timing (the flash will fire in non-single pulse flash when the shutter speed is 1/600).
How to Match the Flash and the Shutter
High-speed shutter single pulse flash requires very strict time alignment. As shown in the figure, the shutter needs to be turned on at the optimal light effect of the flash. Matching method is as follows:
Set the flash to M (manual) flash mode and enter the menu, turn on ADJ in the camera flash timing settings. Input the ADJ parameter which is related to the camera and flash used. If you are using iT32+X5 S with A9MIII, this parameter is about 140 microseconds when iT32+X5 S is wireless off, and about 540 microseconds when iT32+X5 S is wireless on (if you are using other global shutter cameras, you need to full-time match to determine the time). After setting the above parameters, adjust the camera shutter to 1/80000 and the flash power to 1/128 (The matching requirements are higher for faster shutter speed and lower power, if you adjust the right combination, other combinations are usually suitable. When set to a fast shutter speed and high power, since the flash timing is much longer than the shutter time, you can move the time back and select the peak of the flash.), you can finetune the ADJ parameters to the optimal exposure time in case the flash is out of sync, then you can test the shootings under other shutters.

Flash timing diagram: A: Amount of flash light, B: Time, C: Shutter speed, D: Amount of flash light in 1/128 power, F: Exposed amount of flash light, G: Flash starting timing.
Important Notes:
- If you set the camera's shutter speed faster than 1/10000 and take a picture, the brightness and color may vary.
- For cameras equipped with a global shutter image sensor, the HSS icon will not be displayed on the panel regardless of whether the high-speed sync setting is [ON] or [OFF].
- When the flash is connected to the camera using a sync cord, the camera shoots with a traditional high-speed sync instead of using the global shutter sync, so the distance that the flash's light can reach is shortened.
8.13. Sync Triggering
Insert a sync cord or trigger plug into the sync cord jack. The flash will be fired synchronously with the camera shutter.
9. Maintenance
9.1. Over-Temperature Protection
To avoid overheating and deteriorating the flash head, observe the following guidelines for continuous flashes:
- Do not fire more than the specified continuous flashes in fast succession at 1/1 full power.
- Do not fire more than 40 continuous flashes in fast succession at 1/1 full power in HSS mode.
If you exceed these limits, the inner over-temperature protection function may activate, extending the recycle time to over 10 seconds. If this occurs, allow a rest time of about 10 minutes for the flash unit to return to normal. When over-temperature protection is active, < > is shown on the display.
Number of Flashes that will Activate Over-Temperature Protection:
| Power Output Level | Number of Flashes |
|---|---|
| 1/1 | 40 |
| 1/2 | 60 |
| 1/4 | 120 |
| 1/8 | 200 |
| 1/16 | 300 |
| 1/32 | 600 |
| 1/64 | 1200 |
| 1/128 | 2000 |
Number of Flashes that will Activate Over-Temperature Protection in HSS Mode:
| Power Output Level | Number of Flashes |
|---|---|
| 1/1 | 40 |
| 1/2 | 75 |
| 1/4 | 100 |
9.2. Lithium Battery Storage Recommendations
This product is equipped with lithium batteries, which have limited lifespans (typically 300-500 complete charge-discharge cycles). As usage frequency and duration increase, its maximum storage capacity will gradually decrease. Regularly check the battery's condition. If charging time significantly increases or battery life significantly decreases, consider replacing it.
- Charge the battery to about 50% before storage.
- Charge it to about 50% at least every six months. Failure to perform maintenance charging over an extended period may cause the battery to suffer permanent performance degradation or even become unusable due to excessive discharge.
- Removable batteries should be stored separately. The storage temperature should be between 0°C and 40°C.
Lithium Battery Safety Notes:
- Do not disassemble, crush, or puncture the battery.
- The battery is not waterproof; do not immerse it in fog or water.
- Avoid short-circuiting the battery contacts.
- Do not expose the battery to or put it into fire.
- Do not expose the battery to temperatures above 60°C.
- Keep out of reach of children.
- Protect the battery from excessive shock or vibration.
- Do not use a damaged battery.
- If the battery leaks, avoid contact with the leaking fluid.
- If battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.
- Confirm and comply with all relevant local laws and regulations when handling any batteries.
10. Troubleshooting
If you encounter problems, refer to this guide for solutions.
10.1. The camera flash does not fire.
- Attach the camera's mounting foot securely to the camera.
- If the electrical contacts of the camera flash and camera are dirty, clean the contacts with a dry cloth.
- If the < > or < > icon is not displayed in the viewfinder of the camera, wait until the flash is fully recycled and the flash ready indicator lights up.
- If the flash ready indicator does not light up after a long wait, check whether the battery power is sufficient. If the battery power is low, please replace or charge the battery immediately.
10.2. The power turns off by itself.
- Setting as Wi-Off/Sender Mode with Standby Function On: The flash will enter sleep mode automatically after 90 seconds of idle use. Press the camera shutter halfway or press any button to wake up the flash unit.
- Setting as Wi-Off/Sender Mode with Standby Function Off and Auto Off Function On: The flash will automatically shut down after 60 minutes (or 30 minutes, 90 minutes) of idle use. Restart the flash unit.
- Setting as Receiver Mode with Auto Off Function On: The flash will automatically shut down after 60 minutes (or 30 minutes, 90 minutes) of idle use. Restart the flash unit.
10.3. The flash exposure is underexposed or overexposed.
- You used high-speed sync. With high-speed sync, the effective flash range will be shorter. Make sure the subject is within the effective flash range displayed.
- The subject appears too dark or too bright. Set the proper FEC value.
10.4. No response when pressing buttons or touching the screen.
- Software malfunction in the device. Press and hold the < < / > > and MENU button simultaneously to force a shutdown, then restart the device to check if it functions normally.
10.5. Reason & Solution of Not Triggering in Godox 2.4G Wireless
- Disturbed by 2.4G signal in outer environment (e.g., wireless base station, 2.4G WiFi router, Bluetooth, etc.):
→ Adjust the channel CH setting on the flash trigger (add 10+ channels) and use a channel that is not disturbed. Or turn off other 2.4G equipment. - Flash has not finished its recycle or caught up with continuous shooting speed (flash ready indicator is not lightened), or flash is under over-heat protection/other abnormal situations:
→ Downgrade the flash power output. If the flash is in TTL mode, try changing it to M mode (a pre-flash is needed in TTL mode). - Distance between flash trigger and flash is too close (<0.5m):
→ Turn on the "close distance wireless mode". Set the triggering distance to 0-30m. - Flash trigger and receiver end equipment are in low battery states:
→ Replace the battery or charge it in time. - Flash trigger's firmware is an older version:
→ Upgrade the firmware of the flash trigger referring to the instruction manual for specific firmware upgrades. - Camera's firmware is an older version:
→ Upgrade the firmware of the camera referring to its instruction manual.
11. Technical Data & Specifications

Detailed technical specifications for the Godox iT32 and X5.
| Feature | iT32+X5 S | iT32+X5 C/N/O/F |
|---|---|---|
| Global Shutter Sync Shooting | ||
| Global Shutter Sync Shooting | Provided | Unprovided |
| Radio Wireless Global Shutter Sync | Provided | Unprovided |
| Guide Number (1/1 step) | Approx. GN18 (ISO 100, in meters) | |
| Flash Duration (t0.1) | 1/1000s ~ 1/30000s | |
| Exposure Control | ||
| Exposure Control System | TTL auto flash and manual flash | |
| Flash Exposure Compensation (FEC) | ±3 steps with 1/3 increment each step | |
| Sync Mode | High-speed sync (up to 1/8000 seconds, or 1/80000 seconds with Sony cameras equipped with global shutter), first-curtain sync, and second-curtain sync | |
| Multi Flash | Provided (up to 100 times, 100Hz) | |
| Wireless Flash (Radio 2.4G Transmission) | ||
| Wireless Function | Sender, Receiver | |
| Sender Groups | M, A, B, C (iT32+X5 S/N/F/O) | A, B, C, D (iT32+X5 C) |
| Receiver Groups | A, B, C, D | |
| Transmission Range (approx.) | Max. 80m (Max. 20m in separated triggering) | |
| Channels | 32: 1-32 | |
| ID | OFF/1-99 | |
| Power Supply | ||
| Lithium Battery | iT32: 7.4V/900mAh; X5: 3.8V/100mAh | |
| Recycle Time (1/1 step) | Approx. 1.5s (As the number of consecutive flashes increases and the temperature rises, the recycle time becomes longer.) | |
| Number of Flashes (1/1 step) | Approx. 510 | |
| Power Saving | Provide standby and auto off functions | |
| Sync Triggering Mode | Hot shoe, 2.5mm sync cord | |
| Dimension and Net Weight | ||
| Dimension | iT32: 56*39*101mm; X5: 1.26"*1.26"*1.06" | |
| Net Weight | iT32: 169g; X5: 23g | |
Specifications and data may be subject to changes without notice.
11.1. Compatible Camera Models
Note: These tables only list tested camera models, not all cameras. For compatibility with other camera models, a self-test is recommended. Rights to modify these tables are retained.
iT32+X5 C (Canon)
80D, 90D, 7D, 6D, 70D, 750D, 760D, 5DMarkIV, EOS 1DX, 6DMarkII, 77D, 800D, 5DMarkIII, 5DMarkII, 60D, 7D MarkII, 600D, 50D, 30D, 40D, 500D, M5, M3, M50, R, RP, M6II, R5, 1500D, 3000D, R7, R6II, R50, R8, R5C, R10, R100, R5II, R3, 200DII
iT32+X5 S (Sony)
a77II, a99, a77, DSC-RX10, α6000, α7R, α350, a7RII(4.0), α7RIII, a7M3, α9, a7RIV, α7R5, α7MIV, ZV-E10, A9III, A7C, A7CII, a6400, a6500
iT32+X5 N (Nikon)
D800, D750, D700, D610, D500, D200, D300S, D5, D4, D810, D780, D5300, D5200, D5100, D5000, D3300, D3100, D60, Z6, Z7II, Z8, ZFC
iT32+X5 O (OM SYSTEM/Panasonic)
OM SYSTEM: E-M1, PEN-F, E-M10II, E-PL8, E-P5, E-M10III
Panasonic: GH4, LX100, DMC-GF1, DMC-G85, DMC-GX85, DMC-LX100, DMC-FZ2500GK, S1
iT32+X5 F (Fujifilm)
A: X-Pro2, X-T20, X-T2, X-T1, GFX50s, GFX50R, X-T30, X-T4, X-T3, X-S20, X-T5
B: X-Pro1, X-T10, X-E1, X-A3
C: X100F, X100T
Note: X100T does not have second curtain sync (REAR) function.
12. Firmware Upgrade
This product supports firmware upgrade through the USB-C port. Please use a USB-C cable (sold separately).
- Firmware upgrade requires Godox G3 software. Download and install the software (Godox G3 V2.0 for macOS, Godox G3 V1.1 for Windows) before upgrading.
- Choose the related firmware file.
- Press the SET button and insert into the USB-C port for upgrade.
- Refer to the latest electronic version of the instruction manual for detailed steps.
- The download website for firmware upgrade is: https://www.godox.com.cn/firmware-G3/
13. User Tips
- The iT32 is generally easy to use and pairs well with the X5 trigger.
- Consider purchasing two or three units for more versatile off-camera lighting setups and creative effects.
- The compact size of the iT32 and X5 makes it a good fit for smaller camera bodies like Leica M and Q series.
- While the control wheel is convenient, it can be easy to rotate. Utilize the 'lock' function to prevent accidental changes.
- The built-in diffuser can be stiff; exercise care when retracting it.
14. Frequently Asked Questions (FAQ)
- Q: What comes included with the flash?
- A: The standard package includes the iT32 Flash Body, USB-C Charging Cable, Magnetic Mini Stand, Diffuser, two Magnetic Color Filters (1/2 orange and 1/1 orange), a Storage Bag, and the Instruction Manual. The X5 TTL Wireless Flash Trigger is sold separately.
- Q: Is the Sony A7II camera compatible?
- A: Yes, the Sony A7II is listed as a compatible camera model for the iT32+X5 S version. Please refer to the 'Compatible Camera Models' section for a full list.
- Q: Does the flash include the X5 trigger?
- A: No, the X5 TTL Wireless Flash Trigger is sold separately. The iT32 flash body is designed to work with interchangeable X5 versions for different camera systems.
15. Warranty & Support
15.1. Warranty Period
The warranty period for products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the purchase date when the product is bought for the first time. The purchase date is considered as the date registered on the warranty card when buying the product.
| Parts | Maintenance Period (month) | Warranty Service Type |
|---|---|---|
| Internal circuit board | 12 | Customer sends the product to designated site |
| Other items (flash tube, optical accessories, cables, package, etc) | NO | Without warranty |
15.2. How to Get Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, Godox may offer maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered an obligation.
15.3. Inapplicable Cases (Warranty Exclusions)
The guarantee and service offered by this document are not applicable in the following cases:
- The product or accessory has expired its warranty period.
- Breakage or damage caused by inappropriate usage, maintenance, or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to improper temperature, solvent, acid, base, flooding, and damp environments, etc.
- Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition, and detachment.
- The original identifying information of the product or accessory is modified, alternated, or removed.
- No valid warranty card.
- Breakage or damage caused by using illegally authorized, nonstandard, or non-public released software.
- Breakage or damage caused by force majeure or accident.
- Breakage or damage that could not be attributed to the product itself.
Once these situations occur, you should seek solutions from the related responsible parties, and Godox assumes no responsibility. Damage caused by parts, accessories, and software that are beyond the warranty period or scope is not included in the maintenance scope. Normal discoloration, abrasion, and consumption are not considered breakage within the maintenance scope.
15.4. Support Contact
Godox After-sale Service Call: +86-755-29609320 (8062)
16. Regulatory Information
16.1. Warning
iT32:
- Operating frequency: 2412.99MHz-2464.49MHz
- Maximum EIRP Power: 5dBm
X5 C/X5 N/X5 S/X5 F/X5 O:
- Operating frequency: 2412.99MHz-2464.49MHz
- Maximum EIRP Power: 5dBm
16.2. Declaration of Conformity
GODOX Photo Equipment Co., Ltd. hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states. For more information of DoC, Please click this web link: https://www.godox.com/eu-declaration-of-conformity/
The device complies with RF specifications when the device is used at 0mm from your body.
16.3. FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
16.4. IC Warning
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference received, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux normes RSS exemptées de licence d'Innovation, Sciences et Développement économique Canada. L'exploitation est soumise aux deux conditions suivantes:
- Cet appareil ne peut pas causer d'interférences, et
- Cet appareil doit accepter toute interférence, y compris celles qui pourraient entraîner un fonctionnement accidentel de l'appareil.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Avertissement RF pour les appareils portables: L'appareil a été évalué pour répondre aux exigences générales d'exposition aux radiofréquences. Équipement Peut être utilisé sans restriction dans des conditions d'exposition portables.