1. Important Safety Information
⚠️ WARNING: Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.
⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
1.1 General Safety Guidelines
- All users must read and understand this manual before their first use of the E-bike. Additional manuals for components may also be provided and should be read.
- Ensure you comprehend all instructions and safety notes/warnings.
- Ensure the bike fits you properly before your first use. You may lose control or fall if your bike is too big or too small.
- Ensure correct setup and tightening is performed on your bike before first using it and check the setup, tightening, and condition regularly.
- Familiarize yourself with the laws and requirements of operating this product in your riding area.
- Ensure handlebar grips are undamaged and properly installed. Loose or damaged grips can cause loss of control.
- Do not use this product with standard bike trailers, stands, electric bike racks, or accessories that have not been tested and verified for safety and compatibility by ZEFIORA.
- Off-road riding requires close attention, specific skills, and presents variable conditions and hazards. Wear appropriate safety gear and do not ride alone in remote areas.
- Engaging in extreme riding is extremely dangerous and should be avoided. Bikes and bike parts have strength and integrity limitations.
- Failure to perform and confirm proper installation, compatibility, operation, or maintenance can result in serious injury or death.
- It is recommended to not ride at night if avoidable. Ride at night only if necessary.
1.2 Riding Safety
- Always Wear A Helmet: Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and use eye protection.
- Know Your E-bike: Your new E-bike incorporates many features and functions. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
- Ride Within Your Limits: Take it slow until you are familiar with the riding conditions. Be especially careful in wet conditions as traction can be greatly reduced and brakes become less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgment and safety.
2. Parts Identification
Familiarize yourself with the components of your ZEFIORA V10 electric bicycle using the diagram below.

Figure 2: Labeled diagram of the ZEFIORA V10 Electric Bicycle components.
- Front: LED Headlight, Front Fender, Front Fork, Disc Brake Rotor, Tire
- Handlebar Area: Display, Handlebar, Add Single-speed Button, Power Button, Light Switch, Horn
- Frame: Bike Frame, Seat, Battery, Controller
- Rear: Rear Rack, Light, Rear Fender, Bike Motor, Derailleur, Tire
- Drivetrain: Chain, Crank, Pedals
3. Setup (Assembly Instructions)
The following assembly steps are a general guide. If you encounter difficulties, contact customer service for assistance or a video guide.
3.1 Unpacking and Initial Setup
- Unpack the e-bike from the carton and carefully lay out all contents. Remove all packaging material protecting the bike frame and components.
- Please recycle packaging materials, especially cardboard and foam.
3.2 Front Wheel Installation

Figure 3: Visual guide for unpacking and front wheel installation.
- Insert the front wheel into the front fork.
- Insert the fork anti-spin hook plate and washer.
- Finally, insert the nut and tighten it securely.
3.3 Kickstand Installation
- Remove the kickstand from its packaging.
- Position the kickstand on the inside of the frame.
- Align the screws from the outside and tighten them clockwise using an M6 screwdriver.
3.4 Handlebar Installation
- Loosen the handlebar mounting screws on the stem.
- Place the handlebars onto the stem.
- Tighten the screws securely.
- Adjust the front of the vehicle so it is level with the tires, then tighten the bolts on both sides of the stem.
3.5 Headlight Installation
- Open the headlight mounting brackets on both sides.
- Install the black spacers.
- Locate the headlight wiring harness and the main wiring harness (both have arrow markings).
- Align the arrows and insert them into the harness, ensuring they are securely plugged in.
- Tighten the screws on both sides of the headlight mounting brackets.
3.6 Front Fender Installation
- Remove the front fender from its packaging.
- Insert the front fender from back to front into its mounting position.
- Tighten the screws to secure the fender.
- Secure the mounting brackets on both sides with screws.
3.7 Adjusting Brake Tightness
Abnormal noise from brakes can occur due to thicker brake pads. This is normal and should subside after a few rides. If noise persists, follow these steps or consult a repair shop.

Figure 4: Visual guide for adjusting disc brake caliper.
- Prepare Tools: Locate the disc brake caliper (metal part holding the brake disc). You will see two vertical screws (usually M6 Allen wrench).
- Loosen Screws: Use an M6 Allen wrench to slightly loosen these two screws (1 to 1.5 turns). This allows the clamp to move slightly. Do not remove them completely.
- Alignment Position: Gently straighten the wheel to ensure it's centered. Adjust the brake caliper position (left/right) until the brake disc is exactly in the center of the two brake pads, with even clearance. Rotate the wheel to check for smooth rotation without friction noise.
- Tighten Screws: While holding the caliper in the optimal position, tighten the two loosened screws alternately and in stages. Do not overtighten one screw at once. After tightening, rotate the wheel to confirm no abnormal noises. Repeat steps 2-3 if slight friction remains.
3.8 Rear Rack Installation (if applicable)
- Locate the taillight, loosen its screws, and remove it.
- Unscrew all four screws on the back of the seat area.
- Place the rear rack onto the rear shelf, align the holes, and tighten the screws on both sides.
3.9 Taillight and Rear Seat Bag Installation
- Locate the taillight wiring and secure it with cable ties provided.
- Locate the headlight wiring harness and the main wiring harness (with arrow markings). Align and insert them, ensuring a secure connection.
- Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.
4. Operating Your E-bike
4.1 Operation Meter
The display provides essential information about your ride and bike status.

Figure 5: Overview of the operation meter display.
- Display Elements: Logo, Battery Level, Total Distance (ODO), Single Trip (TRIP), Boost Icon, Headlight Icon, NFC Icon, Speed (Km/h), Gear (PAS), Status Bar.
4.1.1 Meter Functions
- Power On/Off: Press and hold the [Power button] for 2 seconds to turn the device on or off.
- Gear Shift: Press the [+ button] briefly to increase by one gear, and press the [- button] briefly to decrease by one gear.
- ODO/TRIP Data Display Toggle: Briefly press the [Power button] to switch between displaying ODO and TRIP data. The default display is TRIP.
- Implementation Model: Press and hold the [- button] to enter Implementation Model, and release the button to exit.
4.2 Setting Menu Operations
To access general settings, press and hold both the [+ button] and [- button] simultaneously.
4.2.1 Menu Navigation
- Switch Setting Items: In the settings menu, press the [Power button] briefly to toggle between options.
- Adjust Setting Parameters: Press the [+ button] or [- button] briefly to modify parameters.
- Confirm: Press and hold the [Power button] to save changes and return to the previous level.
- Return to Home Page: Press and hold the [- button] to exit without saving and return to the main interface, or remain inactive for 60 seconds to automatically exit.
4.2.2 Setting Menu Options
- SET 1: Wheel Diameter (Adjustable range: 16-29 inches, default: 26 inches. Not adjustable by default.)
- SET 2: Speed Limit (Adjustable range: 1-99, default: 25 km/h. Not adjustable by default.)
- SET 3: Unit (Options: Metric (KM/H) or Imperial (blank), default: KM/H.)
- SET 4: Screen Brightness (Adjustable range: 1-3 levels, default: Level 3.)
- SET 5: Auto Sleep Time (Adjustable range: 1-60 minutes, default: 10 minutes.)
- SET 6: Single Trip Auto Reset (Options:
