Dynamic Trajectory Car Rear View Camera Dynamic Trajectory Car Rear View Camera

Contents

AHD Dynamic Trajectory Car Rear View Camera User Manual

Model: Dynamic Trajectory Car Rear View Camera

1. Product Overview

This manual provides detailed instructions for the installation, operation, and maintenance of your AHD Dynamic Trajectory Car Rear View Camera with EU European License Plate Frame. Please read this manual thoroughly before installation and use.

Product Overview: Car Rear View Camera with EU License Plate Frame, showing CVBS/AHD modes and dynamic trajectory lines.

Figure 1: Product Overview - Dynamic Trajectory Camera integrated into an EU license plate frame.

2. Package Contents

Please check the package contents upon opening to ensure all items are present and undamaged.

  • Car Camera (integrated into license plate frame)
  • 6-meter Video Cable
  • 1-meter Power Cable
  • User Manual (this document)
Packing List: Image showing the car camera, 6m video cable, 1m power cable, and user manual.

Figure 2: Included Components.

3. Setup and Installation

3.1. Important Considerations Before Installation

  • Ensure your car monitor supports the desired video signal (CVBS or AHD).
  • If switching to AHD, verify your Android device/monitor supports AHD signal (720P).

3.2. Cable Cutting Instructions (CVBS/AHD Signal Switching)

Your camera supports both CVBS and AHD video signals. The white cable controls this conversion. By default, the camera outputs a CVBS signal.

  • For CVBS Signal (Default): Do not cut the white cable.
  • For AHD Signal: Cut the white cable. Before doing so, ensure your monitor is set to or supports the AHD channel (e.g., AHD 720P).
Cable Cutting Instructions: Image showing a white cable being cut with scissors, and a comparison of CVBS (before cutting) and AHD (after cutting) video output.

Figure 3: CVBS/AHD Signal Conversion via White Cable.

Before purchasing, check monitor support for AHD 720P. Image shows white cable for signal conversion, with CVBS and AHD output examples.

Figure 4: Reminder to check monitor compatibility before cutting the white cable.

3.3. Wiring Diagram

Follow the diagram below for proper installation. Ensure all connections are secure.

Installation Schematic: Wiring diagram showing connections for the car camera. Black wire to GND, Red wire to Reversing Light Positive, Video Cable to Monitor, Trigger Wire to Reversing Light Positive.

Figure 5: Camera Installation Schematic.

  1. Connect the Black wire of the power cable to a vehicle ground (GND).
  2. Connect the Red wire of the power cable to the reversing light positive (+12V).
  3. Connect one end of the Video Cable to the camera's video output.
  4. Connect the other end of the Video Cable to your car monitor's video input.
  5. Connect the Trigger Wire (usually a small red wire extending from the video cable near the monitor end) to the reversing light positive (+12V). This tells the monitor to switch to the camera view when reverse gear is engaged.

3.4. Camera Angle Adjustment

The camera lens can be manually adjusted up or down to achieve the optimal viewing angle for your vehicle.

Adjustable camera angle: Image showing the camera lens can be tilted up or down within the license plate frame.

Figure 6: Adjustable Camera Lens.

4. Operation

4.1. Dynamic Trajectory Guidelines

This camera features dynamic trajectory guidelines that assist in parking and reversing. These lines change according to the vehicle's movement angle and speed when reversing.

Note: When turning the steering wheel while parking, the dynamic trajectory lines will not change. They react to the actual movement of the vehicle body.

Dynamic Trajectory Instructions: Series of images showing steering wheel turning left, straight, and right, with corresponding dynamic guide lines on the reverse camera view.

Figure 7: Dynamic Trajectory in Action.

4.2. Monitor Settings for Camera Display

To ensure proper image display, your car monitor channel needs to be consistent with the camera channel (CVBS or AHD).

  • For AHD Channel: The monitor needs to be set to AHD 720P (e.g., 25fps or 30Hz).
  • For CVBS Channel: Set the display screen to CVBS/NTSC.

Camera Setting on Android Devices (if applicable):

  • To select AHD 720P: Go to Car settings >> Factory settings >> Reverse (picture) settings >> Select AHD 720P.
  • To select CVBS NTSC: If your Android device does not support AHD signal, you need to set it to CVBS signal. Go to Car Setting >> Factory Setting >> Reverse (Picture) Setting >> Select CVBS NTSC.
User Manual Page 1: Details on camera settings for AHD and CVBS on Android devices, and a description of dynamic trajectory.

Figure 8: Camera Setting Interface Example.

5. Maintenance

  • Lens Cleaning: Periodically clean the camera lens with a soft, damp cloth to ensure a clear view. Avoid abrasive cleaners.
  • Connection Check: Occasionally check all wiring connections to ensure they are secure and free from corrosion.
  • Environmental Protection: While waterproof, avoid directing high-pressure water jets directly at the camera for extended periods.

6. Troubleshooting

6.1. Common Display Issues and Solutions

If you encounter issues such as a black screen, no signal, blurred screen, or a black and white image, follow these steps:

User Manual Page 2: Details on control line adjustment, installation schematic, and possible issues with camera installation including black screen, no signal, blurred screen, and solutions.

Figure 9: Troubleshooting Guide.

  1. Check Monitor Channel Consistency:
    • Confirm if the camera is outputting CVBS or AHD (default is CVBS; cutting the white wire switches to AHD).
    • Ensure your car monitor is set to the corresponding channel (AHD 720P for AHD camera, CVBS/NTSC for CVBS camera).
  2. Check All Connections: Ensure the power cable and video cable are securely connected and free from damage.
  3. Power Supply: Verify the camera is receiving adequate power (12V).

6.2. Screen Flicker

If the display screen flashes after installation, it may be due to insufficient power supply to the camera, often caused by other high-power appliances in the car.

Solution:

  • Connect the negative black wire of the power supply to a larger metal ground point (iron block) in the vehicle to help stabilize the voltage.
  • Consider using a power regulator or other anti-interference products to ensure a stable power supply to the camera.

7. Specifications

FeatureSpecification
Lens MaterialGlass
Guiding LineYes (Dynamic Trajectory)
Video Cable Length6 Meters
Shell MaterialPlastic
ConnectivityWired
Body MaterialABS
Viewing Angle170°
Operating Voltage12 V
Frame Length55 cm (21.65 inches)
Frame Height14 cm (5.5 inches)
Mounting Width48 cm (18.89 inches)
Package Weight0.589 kg
Package Dimensions (L x W x H)58 cm x 16 cm x 4 cm
Product Size: Diagram showing dimensions of the license plate frame with camera: 55cm length, 14cm height, 48cm mounting width.

Figure 10: Product Dimensions.

8. User Tips

  • Test Before Final Mounting: Before fully securing the license plate frame and routing all cables, temporarily connect the camera and test its functionality with your monitor. This allows for easier troubleshooting or adjustments.
  • Cable Management: Route cables carefully to avoid pinching, abrasion, or interference with moving parts. Use zip ties or cable clips to secure them.

9. Warranty and Support

For warranty information or technical support, please refer to the seller or the platform where the product was purchased. Keep your purchase receipt as proof of purchase.

An electronic version of this user manual may also be available for download from the seller's product page or directly via this link: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.