NVIDIA P3700

Contents

NEW SHIELD Remote P3700 Control User Manual

For NVIDIA 2019 Shield TV and Shield TV Pro

Model: P3700

1. Introduction

This manual provides detailed instructions for setting up, operating, and troubleshooting your NEW SHIELD Remote P3700 Control. This remote is designed for seamless compatibility with NVIDIA 2019 Shield TV and Shield TV Pro devices, offering features such as voice control and a backlit keypad for enhanced user experience.

2. Package Contents

  • P3700 Remote Control
  • (Batteries not included, requires 2x AAA batteries)

3. Setup

3.1. Battery Installation

The remote control requires two AAA batteries (not included).

  1. Open the battery compartment cover on the back of the remote control.
  2. Insert 2 AAA batteries, ensuring correct polarity (+/-).
  3. Close the battery compartment cover.
P3700 Remote Control with battery compartment visible
Image: P3700 Remote Control showing the battery compartment area.

3.2. Pairing the Remote Control

Follow these steps to pair your P3700 Remote Control with your NVIDIA Shield TV device:

  1. Install 2 AAA batteries into the remote control unit (RCU). The backlight of the remote control will flash, indicating it's ready for pairing. Pairing can often be completed by simply powering on your TV stick.
  2. If the remote does not automatically pair with your TV stick, press and hold the Back button and the Home button simultaneously for 3 seconds. The backlight will flash, and the pairing operation with the host device will be completed.
Diagram showing pairing instructions for the remote control
Image: Visual guide for pairing the remote control, indicating the Back and Home buttons to press.

4. Operating Instructions

4.1. RCU Infrared (IR) Code Transmission Function

After connecting the remote control to your TV stick, you can control your TV through IR. The buttons with this function are: TV Power, Volume Up (Vol+), and Volume Down (Vol-).

To configure IR settings for your TV/projection:

  1. Go to Settings > Device preference settings > Display & Audio > Power controls > Change IR settings for TV/projection.
  2. Follow the on-screen prompts to complete the configuration for TV Power IR.

To configure IR settings for Volume Control:

  1. Go to Settings > Device preference settings > Volume Control > Change IR settings.
  2. Follow the on-screen prompts to complete the configuration for Vol+ and Vol- IR.

4.2. Backlight Settings

The remote control features a backlight for improved visibility in low-light conditions.

  1. Navigate to Settings > Remote control and accessories > SHIELD accessories > Already connected to SHIELD remote control > Backlight Settings.
  2. You can adjust the brightness and duration of the backlight by pressing the left and right arrow keys on the remote.

4.3. Voice Control

The remote control supports voice commands. Press the microphone button to activate voice input and speak your commands to your NVIDIA Shield TV device.

4.4. Media Playback and Navigation

The remote includes dedicated buttons for media playback and navigation:

  • Directional Pad (D-Pad) and Select Button: For navigating menus and making selections.
  • Play/Pause: To play or pause media.
  • Fast Forward / Rewind: To skip forward or backward in media.
  • Netflix Button: Direct access to the Netflix application.
Front view of the P3700 Remote Control showing all buttons
Image: Front view of the P3700 Remote Control, highlighting the layout of navigation, media, and voice control buttons.

5. Maintenance

5.1. Cleaning

To clean your remote control, use a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the surface.

5.2. Battery Replacement

Replace batteries when the remote's performance degrades or it stops responding. Always replace both AAA batteries at the same time with new ones.

6. Troubleshooting

ProblemPossible CauseSolution
Remote not pairing or responding.Low or dead batteries; incorrect pairing procedure; remote not recognized.
  • Ensure fresh AAA batteries are installed correctly.
  • Repeat the pairing process (Section 3.2).
  • Ensure the Shield TV is powered on and within range.
Backlight not working automatically or at all.Backlight settings; specific model behavior.
  • Check Backlight Settings (Section 4.2) on your Shield TV.
  • Note that some models may only activate backlight during pairing or when a button is pressed, rather than automatically upon lifting.
Power or Volume buttons not controlling TV.IR function not configured or incorrectly configured.
  • Follow the IR Code Transmission Function setup (Section 4.1) to configure these buttons for your TV.
Remote loses connection after Shield TV turns off.Specific device compatibility issue or software glitch.
  • Try re-pairing the remote.
  • Ensure your Shield TV's software is up to date.
  • Consider restarting the Shield TV device.
Excessive battery drain.Faulty batteries; constant backlight activation; remote malfunction.
  • Use high-quality alkaline batteries.
  • Adjust backlight duration to a shorter setting (Section 4.2).
  • If the issue persists with new batteries and optimized settings, the remote may be faulty.

7. Specifications

FeatureDetail
ModelP3700
CompatibilityNVIDIA 2019 Shield TV, Shield TV Pro
Wireless CommunicationBluetooth
Frequency433 MHz
UseTV Remote Control
Power Source2 x AAA Batteries
CertificationFCC
High-concerned chemicalNone
Support APPNo
Approx. Weight0.068 kg (excluding batteries)

8. User Tips

  • Button Feel: The buttons on this remote are slightly raised, which some users find makes them easier to press compared to flush buttons on other remotes.
  • Backlight Activation: Be aware that the backlight may only activate during the initial pairing process or when a button is pressed, rather than automatically when the remote is picked up.
  • Battery Cover: The battery cover design may differ from the original NVIDIA remote, specifically lacking an extra secure closure mechanism. Ensure it is firmly closed after battery installation.
  • Initial Pairing: While pairing is generally smooth, if automatic pairing fails, remember to manually initiate it by holding the Back and Home buttons for 3 seconds.

9. Warranty and Support

For additional information or support, please refer to the official user manual PDF available at: P3700 Remote Control User Manual (PDF).

Please retain your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.