AC7036-T F100 AC7036-T F100

Contents

User Manual: Detachable Hidden Inductive Touch Sensor Switch

Model: AC-7036-T F100

1. Introduction

The AC-7036-T F100 is an intelligent, contactless touch sensor switch designed for hidden installation. It operates on AC 100V–240V and supports a maximum load of 400W. This switch allows you to control lighting or other devices by simply touching the surface of non-conductive materials like wood, glass, or plastic, providing a seamless and modern control solution for cabinets, wardrobes, and display cases.

Important Note: Due to a manufacturing error, some units may be printed with a '250W' rating. Please disregard this. The actual power rating of this product is 400W, and it is safe to use within this specification.

2. Safety Information

WARNING: Please strictly follow these instructions and safety tips. Use the product with caution.

  • The sensor cable carries high voltage. Always ensure the power supply is disconnected before installation, removal, or any maintenance.
  • The circuit board inside the sensor module carries high voltage. Do not disassemble the housing or attempt to directly touch the circuit board.
  • Do not disassemble the sensor unit.
Safety warning against disassembly and high voltage
Figure 1: Safety warning regarding high voltage and prohibition of disassembly.

3. Setup and Installation

3.1 Package Contents

  • 1x AC-7036-T F100 Touch Sensor Control Switch Module
  • 1x Inductive Sensor Disc with cable

3.2 Installation Steps

Ensure power is OFF before starting installation.

  1. Prepare the Surface: Choose a clean, dry, non-conductive surface (wood, stone, paper, acrylic, plastic, glass) where the touch sensor will be mounted. The material thickness should not exceed 50mm for optimal performance.
  2. Connect the Lamp: Connect your lamp or load correctly to the output terminals of the AC-7036-T control module (LED L and LED N).
  3. Connect Power Input: Connect the AC 100V-240V power supply to the input terminals of the control module (N and L).
  4. Mount the Sensor Disc: Peel off the backing from the double-sided tape on the sensor disc. Mount the sensor disc firmly on the back side of the panel or surface where you want the touch-sensitive area to be. Ensure it is fixed well and there are no conductive metal objects within 8cm of the sensor.
  5. Secure the Control Module: Position the control module in a secure location, ensuring all connections are firm and insulated.
  6. Power On: After all connections are secure and the sensor is fixed in place, you can connect the power supply.
Installation steps for the touch sensor switch
Figure 2: Visual guide for mounting the sensor disc and identifying the touch-sensitive area.
Detailed installation steps with connection points
Figure 3: Step-by-step diagram for connecting the lamp, fixing the switch, and powering on.

3.3 Wiring Diagram

Refer to the diagram below for proper wiring connections based on your load type.

Wiring diagram for various lamp types
Figure 4: Connection Diagram for LED, energy-saving lamps, 12V/24V lamps (with adapter), and AC1100-240V loads.
  • For LED/Energy-Saving Lamps (≤400W, ≤3 Lamps): Connect directly to the output terminals (Lo, Li, Ni, No) of the sensor control switch.
  • For 12V/24V Lamps: An external constant voltage adapter (DC12V/24V) is required. The adapter connects to the AC output of the switch, and the 12V/24V lamp connects to the adapter.
  • For AC1100-240V Loads: Connect directly to the output terminals of the sensor control switch.

3.4 Installation Video Guide

Watch this video for a visual demonstration of the installation process.

Video 1: Step-by-step installation guide for the touch sensor switch.

4. Operating Instructions

The AC-7036-T F100 switch operates with a simple touch mechanism:

  • To Turn On: Lightly touch the designated touch-sensitive area on the surface.
  • To Turn Off: Touch the same area again.
  • Non-Dimmable: This switch provides simple ON/OFF functionality and does not support dimming.
Functionality of the touch sensor switch
Figure 5: Illustration of the touch function on the induction surface.

Important Operating Tip: After powering on, do not keep your hand on the switch. If your hand remains on the switch, subsequent touches may not correctly turn the lights off or on.

5. Maintenance

The AC-7036-T F100 requires minimal maintenance:

  • Keep the touch-sensitive surface clean and free from dust or debris to ensure consistent performance.
  • Avoid exposing the unit to excessive moisture or direct water contact.
  • Do not use abrasive cleaners on the sensor disc or control module.

6. Troubleshooting

If the switch does not operate correctly after installation, please check the following:

  • Wiring Connection: Verify that all wires are securely connected and there is no poor contact in the wiring.
  • Sensor Mounting: Ensure the sensor disc is firmly fixed to the surface before powering on. Do not move the sensor after power has been connected.
  • Installation Order: Always fix the switch in its final position first, then apply power.
  • Interference: Check for any conductive metal objects (e.g., metal plates, screws) within 8cm of the sensor disc. Such objects can interfere with its operation. If found, try relocating the sensor to a different position.

7. Specifications

FeatureSpecification
Model NumberAC-7036-T F100
Operating VoltageAC 100V-240V
Max. Power Load400W
Output TypeRelay Output
Sensor Diameter98mm
Sensor Thickness8mm
Penetration DepthUp to 50mm (for F100 model)
Control Module Dimensions70mm (L) x 36mm (W) x 23mm (H)
CertificationsCE, RoHS
Warranty1 Year
Product dimensions for control module and sensor disc
Figure 6: Dimensions of the control module and sensor disc.

8. User Tips

  • Connecting 12V/24V Lights: If you intend to connect 12V or 24V LED strips or lamps, you must use a compatible DC12V/24V constant voltage adapter. The adapter connects to the switch's output, and your low-voltage lights connect to the adapter. Do not connect low-voltage lights directly to the switch.
  • Touch Accuracy: If you experience inconsistent touch response, double-check the installation steps, especially ensuring the sensor is firmly mounted and there are no nearby conductive materials interfering with its operation.
  • Power Rating: Despite any '250W' markings, this switch is rated for 400W. You can safely connect loads up to 400 watts.

9. Warranty and Support

This product comes with a 1-year warranty from the date of purchase. If you encounter any issues or require technical assistance, please contact your seller or the manufacturer's support team with your purchase details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.