KEVANLY 60W Car LED Work Light User Manual

1. Product Overview

This manual provides essential information for the safe and effective installation, operation, and maintenance of your KEVANLY 60W Car LED Work Light. This high-brightness LED work light is designed for automotive use, offering dual-color functionality (white and amber) and robust construction suitable for various outdoor conditions.

Figure 1: KEVANLY 60W Car LED Work Light with various light modes demonstrated.

2. Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

• Keep the device and its cord out of reach of children under 3 years old. Keep away from children unless supervised by an adult.
• Do not use this product for purposes other than its intended use.
• Inspect the product before each use; do not use if damaged.
• Follow installation and operation guidelines to avoid injury.
• Do not expose to water or moisture beyond its IP rating.
• Handle with care to avoid cuts or injuries.
• This product is suitable for use in 12-24V wide voltage circuits. It is prohibited to connect voltages outside of this range to avoid burning out the circuit.
• Avoid direct exposure of strong light to the human eye to prevent visual damage.
• Do not install the lamp body on the outside of the vehicle when driving at high speed to prevent it from falling off.
• Do not forcefully impact or drop the lamp body.
• Stay away from high-temperature open flames, oil stains, and corrosive liquids to prevent damage to the light source and circuit.
• Non-professionals are prohibited from disassembling or modifying the internal structure of the lamp body.
• Installation must comply with local vehicle modification regulations. This product cannot replace core vehicle warning/lighting functions. The manufacturer assumes no liability for light damage or vehicle issues resulting from circuit failure or improper installation.

3. Installation

3.1 Wiring Instructions

The work light is designed for a 12V-24V DC power supply system. Proper wiring is crucial for safe and correct operation.

• The red wire should be connected to the positive pole of the 12V-24V power supply.
• The black wire should be connected to the negative pole of the 12V-24V power supply.
• The light can be connected to a car cigarette lighter, directly to the vehicle's battery, or to the original car's reserved 12V-24V power supply interface.
• Ensure all wiring connections are properly insulated after installation to prevent short circuits and ensure safety.

Figure 2: Detailed wiring instructions and light mode demonstration.

3.2 Mounting

The work light comes with a mounting bracket for secure attachment to your vehicle. Ensure the mounting location is stable and does not obstruct any critical vehicle functions or visibility. Tighten all fasteners securely to prevent the light from falling off, especially during high-speed driving or off-road use.

4. Operating Instructions

This LED work light features dual-color functionality, allowing for different lighting effects. The specific control mechanism (e.g., external switch, vehicle's existing controls) will depend on how it is integrated into your vehicle's electrical system.

4.1 Light Modes

The work light supports the following modes, typically controlled by cycling power or a dedicated switch:

• Yellow/White: Standard illumination combining both colors.
• Amber Steadily Lit: Constant amber light, often used for warning or auxiliary lighting.
• Amber-Colored Flowing Water: Dynamic amber light effect.
• Amber Flash: Flashing amber light, suitable for emergency or warning signals.

5. Maintenance

• Regular Inspections: Periodically check the circuit joints and wiring for any signs of looseness, corrosion, or water ingress. Ensure all connections remain secure and insulated.
• Cleaning: Clean the lens and housing with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the light's surface or seals.
• Avoid Disassembly: Do not attempt to disassemble or modify the internal structure of the lamp body. This can void the warranty and lead to product failure or safety hazards.
• Environmental Protection: Keep the light away from high-temperature open flames, oil stains, and corrosive liquids to prevent damage to the light source and circuit.

6. Troubleshooting

• Light Not Turning On:
  • Check the power connection: Ensure the red wire is connected to a positive 12V-24V source and the black wire to a negative/ground.
  • Verify the power source: Confirm that the vehicle's battery or cigarette lighter is providing power.
  • Inspect wiring: Look for any loose, cut, or uninsulated wires.
  • Check for damage: If the light or wiring appears physically damaged, discontinue use.
• Intermittent Operation:
  • Check for loose connections at the light and the power source.
  • Ensure proper insulation to prevent accidental shorting.
• Dim or Incorrect Color Output:
  • Verify the input voltage is within the 12V-24V DC range.
  • Ensure the lens is clean and free from dirt or debris.

7. Specifications

Figure 3: Product dimensions.

Figure 4: Quality features including die-cast aluminum casing and LED lens design.

Figure 5: IP67 Waterproof rating, suitable for all weather conditions.

8. Compliance Information

This product complies with the following EU directives:

• EU General Product Safety Regulation (GPSR)
• Low Voltage Directive (2014/35/EU)
• Electromagnetic Compatibility Directive (2014/30/EU)
• RoHS Environmental Directive (2011/65/EU)

All certification documents are genuine, valid, and consistent with the product information.

Compliance markings.

9. Manufacturer & EU Representative Information

Manufacturer: Guangzhou Kejie Trading Co., Room 302, No. 10, Ou Gang North Street, Ke Mu Long West Road, Tianhe District, Guangzhou City, Guangdong Province, China.

EU Authorized Representative: SUCCESS COURIER SL, Calle de RIO TORMES 13A, oficina 1, Fuenlabrada, Madrid, 28947 Spain.

Importer: Guangzhou Kejie Trading Co., Room 302, No. 10, Ou Gang North Street, Ke Mu Long West Road, Tianhe District, Guangzhou City, Guangdong Province, China.

For further details, please refer to the official user manual PDF: View User Manual (PDF)