PowMr POW-5A-12V

Contents

PowMr 5A 12V Solar Panel Charger Controller User Manual

Model: POW-5A-12V | Brand: PowMr

Introduction

This manual provides essential information for the safe and efficient operation of your PowMr 5A 12V Solar Panel Charger Controller. Designed for small solar home use and street lighting applications, this mini-sized solar controller features an industrial-grade main control chip, supporting 5V or 12V systems with a 5A charging current and a 22V maximum PV input voltage. It offers multiple protection mechanisms and a three-stage charging algorithm to optimize battery performance.

PowMr Solar Controller with wire connectors
Figure 1: PowMr Solar Controller with included wire connectors.

Safety Instructions

  • Ensure your battery has sufficient voltage for the controller to recognize its type before initial installation.
  • Keep the battery cable as short as possible to minimize energy loss.
  • This regulator is designed exclusively for lead-acid batteries (OPEN, AGM, GEL); it is not compatible with nickel metal hydride, lithium-ion, or other battery types.
  • The charge regulator is solely for regulating solar modules. Never connect another charging source to the charge regulator.

Product Features

  • Built-in industrial micro-controller.
  • LED display, auto memory function, IP57 protection.
  • Fully 4-stage PWM charge management.
  • Built-in short-circuit protection, open-circuit protection, reverse protection, and over-load protection.
  • Dual MOSFET reverse current protection, ensuring low heat production.
Product packaging highlighting features and specifications
Figure 2: Product packaging detailing key features and specifications.

Package Contents

The PowMr 5A 12V Solar Controller package typically includes:

  • 1 x PowMr Solar Panel Charger Controller (Model: POW-5A-12V)
  • 4 x Wire Terminals (connectors)
  • 1 x User Manual (this document, also available as a PDF download)

System Connection (Setup)

Follow these steps to connect your solar controller. The reverse order applies when de-installing. An improper sequence can damage the controller.

  1. Connect the Battery: Connect the battery to the charge regulator (plus and minus terminals). The controller will automatically adapt to the battery type.
  2. Connect the Solar Photovoltaic Module: Connect the solar photovoltaic module to the regulator (plus and minus terminals).
  3. Connect the Load: Connect the consumer (load) to the charge regulator (plus and minus terminals).
Diagram of the PowMr Solar Controller with labeled ports for DC Load, Charge, Battery, Solar Panels
Figure 3: Labeled ports on the PowMr Solar Controller.
Comprehensive wiring diagram for the solar controller, showing connections to solar panels, battery, DC loads, inverter, and AC loads
Figure 4: Detailed system wiring diagram for the solar controller.

Note: The controller is designed for 6V/12V auto-adapt. If using a 6V system, all red color voltage values in the specifications table should be divided by 2.

Operating Modes

The operating mode is pre-set within the controller from the factory. For further information, consult your distributor.

Mode Description
Light-open + delay Load turns on after sunset and closes after 1-13 hours.
D2D Dusk to Dawn (with delay).
System Load always outputs (unless battery is low).

Maintenance

To ensure optimal performance and longevity of your solar controller:

  • Regularly inspect all connections for tightness and corrosion.
  • Keep the controller clean and free from dust and debris.
  • Ensure proper ventilation around the controller to prevent overheating.
  • Periodically check battery voltage to ensure it remains within healthy operating parameters.

Troubleshooting

Situation Probable Cause Solution
Charge LED not on when sunny Solar panel opened or reversed Reconnect
Load LED off Mode setting wrong Set again
Battery low Recharge
Load LED slow flashing Overload Reduce load wattage
Load LED slow flashing Short circuit protection Auto reconnect
Power off Battery too low/reverse Check battery/connection

Technical Specifications

Product specifications are subject to change without prior notice.

Parameter Value
Model POW-5A-12V | 5A-12V-L | 5A-12V-ST | 8H
Battery Voltage 6V/12V auto adapt
Charge Current 5A
Discharge Current 5A
Max Solar Input 22V
Charge Drop <0.2V
Discharge Drop <0.25V
Equalization 14.8V
Bulk 14.5V
Acceptance 14.2V PWM
Float 13.8V
Charge Reconnect 13.0V
Discharge Stop 11.2V
Discharge Reconnect 12.6V
Self-consume <10mA
Voltage of Open Light Solar panel 8V (delay 10s)
Voltage of Close Light Solar panel 8V (delay 60s)
Temperature Compensation N/C
Operating Temperature -35~+60 ℃
Size/Weight 60x25x18mm / 50g
Dimensions of the PowMr Solar Controller
Figure 5: Physical dimensions of the solar controller.

User Tips

No specific user tips are available from provided reviews or Q&A content. Always refer to the safety instructions and technical specifications for optimal use.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact your authorized PowMr dealer or the point of purchase. Keep your purchase receipt as proof of purchase.

Product Overview Video

Video 1: Unboxing and feature overview of the PowMr 5A 12V Solar Controller.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.