BAJETON BJ-98PLUS GPS

Contents

BAJETON BJ-98PLUS Walkie Talkie User Manual

Model: BJ-98PLUS GPS

Brand: BAJETON

1. Introduction

Thank you for choosing the BAJETON BJ-98PLUS Walkie Talkie. This manual provides detailed instructions for the safe and effective use of your device. Please read it thoroughly before operation and keep it for future reference.

The BAJETON BJ-98PLUS is a multi-band walkie talkie featuring APRS, GPS, a 2.4-inch large screen, 10W output power, and cross-band repeater capabilities. It supports a wide range of frequencies including CB/SSB/HF, shortwave, medium wave, and long wave reception, along with VHF/UHF transmission and reception.

2. Safety Information

Please observe the following precautions to prevent fire, personal injury, equipment damage, or other accidents:

  • Do not use the equipment in inflammable and explosive environments (e.g., gas, dust, smoke). Turn off the equipment when refueling or parking at gas stations.
  • Do not place the equipment in dusty, wet, or splashed places, or on uneven surfaces.
  • Use this equipment away from interference sources such as TVs, computers, or distribution cabinets.
  • Do not transmit while charging.
  • Do not expose the device to direct sunlight for extended periods or place it near heating devices.
  • If the equipment emits an abnormal odor, turn it off immediately. After ensuring safety, send it to the nearest maintenance site for inspection.
  • Do not modify or adjust this equipment for any reason.
  • Always obey local laws and regulations regarding radio operation.

Disclaimer:

The customer bears all responsibility for equipment failure or accidents caused by violating the above precautions. The manufacturer is not responsible for such incidents.

3. Product Components

Upon unboxing, please check that all the following accessories are included and well-packed. If anything is missing or damaged, contact your local distributor.

Included Accessories
No. Item Quantity
1Radio1
2Antenna1
3Li-ion Battery1
4Charger1
5Belt Clip1
6User Manual1
7Guarantee Card1

Familiar with Radio Diagram

Diagram of BAJETON BJ-98PLUS Walkie Talkie components
Diagram of the BAJETON BJ-98PLUS Walkie Talkie showing its main components.
  1. Antenna
  2. PTT (Push-To-Talk) button
  3. Side-key 1
  4. Side-key 2
  5. Battery
  6. SW/MW/LW FM antenna (Channel knob)
  7. ON/OFF volume knob
  8. Indicator Light
  9. Alarm Button
  10. Display screen
  11. Keypad
  12. MIC (Microphone)
  13. Speaker
  14. Earpiece jack
  15. Type C charging port/programmable jack

4. Controls and Display

Keypad Functions

Key Function Description
PTTTransmit or Exit
Alert KeyDefinable long press and short press functions
Side Key 1Can be set as PTT-2 for transmission (disables custom function). Definable long/short press.
Side Key 2Can be set as PTT-3 for transmission (disables custom function). Definable long/short press.
▲ / ▼Short press: Confirm or enter menu. Long press: Enter DTMF input (standby) or exit menu.
▲DTMF: A, Switch upwards
▼DTMF: B, Switch downwards
0Short press: Enter 0. Long press: Definable functions. Input 0 or Space Bar.
1Short press: Enter 1. Long press: Definable functions. Input 1 or English Letters/Chinese Characters.
2-9Short press: Enter 2-9. Long press: Definable functions. Input 2-9 or English Letters/Chinese Pinyin Codes.
*Short press: Switch channel/frequency/alias. Long press: Lock keypad. DTMF: *. Text input: Delete text.
#Short press: Switch working mode (VFO/channel/zone). Long press: Jump to transmit frequency input menu. DTMF: #. Text input: Enable/disable text input, switch method.

LCD Display Elements

BAJETON BJ-98PLUS Walkie Talkie display showing frequencies and icons
The 2.4-inch large screen display of the BAJETON BJ-98PLUS.
  1. Keyboard Lock
  2. Prompt Tone
  3. Scan
  4. RR Talkaround/TR Reverse Frequency
  5. Multi-Frequency Standby
  6. VOX (Voice Operated Transmit)
  7. GPS
  8. Cross-Band Relay
  9. Battery Icon
  10. Multi-PTT Enable
  11. Received Signal Strength
  12. Received Signal Field Strength Value
  13. High Power / Low Power switchable
  14. CTCSS/DCS / MUT Non-standard DCS / ENC Encrypted DCS
  15. W/N band switchable
  16. FM/AM RX
  17. CH-XXXX Channel Number in Channel Mode / ZONE-XXX Zone Number in Zone Mode
  18. Working Frequency / Working Channel
  19. Main Frequency Area Indicator Icon
  20. Channel Name
  21. Working Frequency Range
  22. A/B/C Main Frequency Area
  23. Received Signal Meter

5. Basic Operation

Working Frequency

The device operates across three main frequency ranges: 64-620MHz, 18-64MHz, and 840-1000MHz. All communication bands utilize the leftmost main antenna port for transmission and reception, unlike shortwave radios that use a middle antenna port.

To select frequency bands, navigate to [Radio Settings] > [Working Frequency] in the menu. The device will restart after confirmation. Always replace the antenna with one corresponding to the selected frequency band to prevent damage.

Frequency Input

  1. Press the # key to switch to VFO Frequency Mode.
  2. Use the numeric keypad to input the desired frequency. Enter 6 or 8 digits.
  3. In [Radio Settings] > [Frequency Input Mode], select [End with 0] for 6-digit input or [Full Input] for 8-digit input.

Repeater Frequency Input

Method 1:

  1. Go to [Channel Settings] > [Offset Frequency] and input the offset frequency using the numeric keypad.
  2. Go to [Channel Settings] > [Offset Direction] to set a positive or negative offset.

Method 2:

In standby mode, long press the # key to enter the [Transmit Frequency] menu. Directly input the transmit frequency, then press the ▲ key to confirm. The device will return to the previous menu. Press the ▼ key to access sub-audio settings and configure the sub-audio frequency.

Transmitting Signals

  1. Press the PTT key to initiate a call on the current frequency. The LED indicator will turn red during transmission.
  2. If [Multi-PTT Switch] is enabled in [Key Definition], Side Key 1 transmits on Band B, and Side Key 2 transmits on Band C.

Receiving Signals

When a signal on the same frequency is received, the LED indicator turns green. If no sub-audio is set, or if the set sub-audio matches the received signal, the device will enable audio output.

UV Cross-Band Relay

Diagram illustrating Cross-Band Repeater function
Cross-Band Repeater functionality, showing U trans U and U trans V modes.
  1. A button can be defined as the [Relay Switch]. When pressed, or when enabled in [Radio Settings] > [Repeater Mode], the device enters cross-band relay mode. In this mode, Channel C is disabled, and only Channels A and B are used for cross-band relay. Signals received on Channel A are retransmitted on Channel B, and vice versa.
  2. The [Repeater Monitor] setting in [Radio Settings] allows the device to listen to relayed voice communications.

DTMF Function

DTMF Encoding Input & Transmission:

  1. In standby mode, long press the ▼ key to enter the DTMF input interface.
  2. Use the numeric keypad to enter DTMF codes. Short press Side Key 2 to delete the last DTMF digit.
  3. Press the PTT key to initiate a call. The device will send the DTMF code after a preset delay.

DTMF Decoding:

When the device receives a signal and DTMF decoding is enabled, the screen will display the received DTMF code.

DTMF Transmission in Analog Mode:

During analog transmission, pressing a key on the keypad will send the corresponding DTMF code.

DTMF Remote Monitoring:

  1. Set a DTMF monitoring code for the device and enable [Accept Remote Control].
  2. Another radio can send the same DTMF code to this device.
  3. Upon receiving and successfully decoding the DTMF code, the device will automatically transmit for 60 seconds, enabling remote monitoring.

6. Advanced Features

DTMF Remote Stun/Kill/Wake

  1. Set a DTMF remote stun/kill/wake code for the device and enable [Accept Remote Control].
  2. Another radio can send the corresponding DTMF code to remotely stun, kill, or wake this device.
  • When stunned, the device cannot transmit or operate the keypad, but can still receive signals.
  • When killed, the device becomes unusable until it receives a wake code.
  • Warning: Ensure a wake code is set, or the device cannot be restored once stunned or killed.

Text Input Function

In the text input menu:

  • # key: Switch between input methods.
  • * key: Delete text or pinyin.
  • Number Input [123]: Enter numbers using the numeric keypad.
  • English Input [AB] / [abc]: Keys 2-9 input corresponding letters. 0 key inputs a space, 1 key inputs symbols. Press a key multiple times to cycle through letters (e.g., pressing 2 will display A, B, C sequentially).
  • Pinyin Input [拼1] / [拼2]: 拼1 for common Chinese characters, 拼2 for extensive character set. Enter pinyin using the numeric keypad, use ▲▼ keys to select characters, and press ▲ key to confirm.

Custom Key Functions & Operations

Diagram showing customizable side keys and keyboard functions
Customizable side keys and keyboard functions for enhanced usability.
  • Monitor: Opens the receiver audio.
  • Power Switch: Toggles high/low power.
  • Scan: Initiates scanning (any key to exit).
  • VOX (Voice-Activated Transmission): Enables/disables.
  • Squelch Level: Adjust squelch settings.
  • Frequency Step: Set frequency step size.
  • Dual Watch: Enable/disable dual frequency monitoring.
  • Priority Transmission: Set to "Edit" or "Busy" mode.
  • TX End Tone: Change transmission end tone type.

Radio Mode

  • Trigger Button: Pressing the trigger button enters radio mode. Pressing the PTT key exits radio mode.
  • # Key Long Press: Switches between radio bands: USW (64-108MHz), SW (2.3-26.1MHz), MW (520-1710KHz), and LW (153-279KHz).
  • # Key Short Press: Switches the radio's demodulation mode. USW is fixed to FM. Other bands can switch between AM, USB, LSB, and CW modes.
  • * Key Short Press: Switches the input type. When the ▼ is pointing to the radio frequency, you can manually enter a frequency. When entering other data, press the ▲▼ keys to switch data content.
  • * Key Long Press: Enters scan mode. Press any key to exit. Long press 0 key to switch scan direction.
  • Note: When using Single Sideband (USB or LSB) demodulation and encountering sharp sound, lower the BFO (Beat Frequency Oscillator) frequency. If the sound is too deep, increase the BFO frequency.
  • Talkaround/Reverse Frequency: Switch repeater frequency mode.
  • Emergency Alarm: Activates alarm mode (any key exits).
  • Single-Tone Transmission: Transmit a continuous tone signal.

One-click Frequency Measurement and Remote Decryption of Privacy Code

  1. After pressing the trigger button, the device enters frequency measurement or remote privacy code decryption mode, scanning surrounding radio frequency signals.
  2. The * key switches between frequency measurement mode and remote sub-audio decryption mode.
  3. During frequency measurement, pressing the PTT key or the ▼ key exits the mode. The # key switches the frequency band.
  4. After measurement, press the ▼ key to retest. Press the ▲ key to save the result to the VFO channel and return to VFO standby mode. Press the PTT key to transmit.

Spectrum Mode

Image showing Spectrum Scanning in action
Spectrum Scanning quickly identifies signal strength and helps avoid frequency collisions.

Enables frequency spectrum analysis.

  1. After pressing the trigger button, enter the spectrum scanning mode. Press the * key to exit.
  2. A short press of the * key switches the input items. The display interface shows scanning center frequency, scanning step size ("SPACE"), and signal amplitude decay ("DECAY").
  3. Use the ▲▼ keys to switch the indicator cursor. The frequency value at the cursor's position is displayed at the bottom, along with RSSI, NOISE, and GLITCH data.

7. Menu Settings

Radio Settings

  • [Name or Call Sign]: Change the device's name or owner's call sign.
  • [Key Lock Timer]: Sets time after which keyboard automatically locks if no operation. Unlock by pressing and holding *.
  • [Backlight Timer]: Sets time for backlight to automatically turn off. Select Off to disable.
  • [Auto Exit Menu]: Menu exits automatically if no operation within set time.
  • [Power Saving Mode]: Reduces battery consumption, but may cause slower reception or missed transmissions.
  • [Scan Mode]: Choose Carrier Mode (pause on signal, resume after signal ends), Time Mode (stop for set period, then resume), or Search Mode (stop once signal detected).
  • [Scan Direction]: Choose to scan upwards or downwards.
  • [Scan Dwell Time]: Sets time device stays on a signal in Time Mode.
  • [Scan Return]: Choose Initial Channel (return to original channel) or Current Channel (stay on current channel).
  • [Alarm Type]: Choose Local Alarm (device emits sound), Remote Alarm (sends signal to remote walkie-talkie), or Local + Remote Alarm.
  • [Operating Frequency Band]: Switch between 16-64MHz, 64-620MHz, and 840-1000MHz. Device restarts after switching; change RF antenna accordingly.
  • [Multi-Frequency Monitoring]: Monitors signals on three frequency bands (A, B, C), but only one can be in reception mode at a time.
  • [Repeater Mode]: Enable/disable UV difference repeater. Frequency C is prohibited when enabled.
  • [Repeater Monitor]: Choose whether the device listens to relayed conversations.
  • [Frequency Input Mode]: Set Tail Number to 0 for 6-digit frequency entry, or Complete Input for 8-digit frequency entry.
  • [Save Channel]: Copy current channel data to a selected channel.
  • [Delete Channel]: Clear data of the selected channel.

Key Definitions (Analog Call Settings)

  • [Multi-PTT Switch]: Side key 1 functions as PTT-2 (Band B), Side key 2 as PTT-3 (Band C). Custom functions disabled.
  • [Squelch Level]: Higher value = deeper squelch, harder to open receiver.
  • [Tone Audio]: Set tone frequency for key's custom function [Send Tone].
  • [MIC Gain]: Adjust microphone sensitivity. Higher value = more sensitive.
  • [SPK Gain]: Adjust speaker volume. Higher value = louder sound. Avoid setting too high to prevent distortion.
  • [Adjacent Channel Limitation]: Increase threshold to mitigate intermittent calls from devices with large frequency offset.
  • [DTMF Transmit Delay]: Sets delay before DTMF tone sent during call.
  • [DTMF Code Interval]: Sets interval between two DTMF tones.
  • [DTMF Code Duration]: Sets duration of a single DTMF tone.
  • [DTMF Transmission Mode]: Sets when DTMF tone sent during call. Choose Off to prevent sending DTMF codes.
  • [DTMF Code Selection]: Choose one of 16 preset DTMF codes.
  • [DTMF Decode Display]: When enabled, received DTMF codes displayed on screen.
  • [DTMF Transmit Gain] & [DTMF Decode Threshold]: Adjust values to maximize compatibility with DTMF codes from different brands. Recommended: transmit gain 64, decode threshold 24.
  • [Accept DTMF Control]: When On, other walkie-talkies can control this device via matching DTMF codes.
  • [Transmit Sound Pressure Refresh Time]: Changes refresh interval for sound pressure bar during transmission.
  • [Receive Signal Strength Refresh Time]: Changes refresh interval for received signal strength table. Adjust to larger value if weak signal causes interference noise.
  • [Temporary Debugging]: Allows adjustment of reception sensitivity and transmission power. Note: Not recommended for users unfamiliar with technical specifications, as it may damage components.

Channel Settings

  • [CTCSS/DCS], [Receive CTCSS/DCS], [Transmit CTCSS/DCS]: Set privacy code type and code for current channel. Switch types using the ▼ key.
  • [Set Transmit Frequency]: Directly set transmit frequency for repeater setup, without adjusting offset.
  • [CTCSS/DCS Encryption Type]: Choose Encryption 1/2/3 to encrypt standard DCS. Choose DCS to disable current sub-audio.
  • [Decode Sub-Audio]: Use frequency measurement to find and use non-standard DCS frequencies.
  • [Scan Add]: Choose Remove to exclude channel from scanning.
  • [Frequency Offset Direction]: Set shift direction after setting [Frequency Shift Frequency]. Up Shift: transmit frequency = receive frequency + shift frequency. Down Shift: transmit frequency = receive frequency - shift frequency.
  • [Frequency Offset Frequency]: Set the offset frequency. Set to 0 to disable.

Zone Settings

The device supports up to 256 zones. Enter the zone settings menu to edit zones and select channel members using the # key.

FM Radio

  • [Call Signal Reception in Radio Mode]: When enabled, device listens for calls on main channel while in radio mode.
  • [Channel List]: Includes 128 preset radio channels. Select a channel, press ▲ to confirm and edit name or set as current radio channel.

Time Management

  • [Auto Power Off]: Enable/disable auto power-off.
  • [Shutdown Timer]: If no operation within set time, device enters low-power sleep mode (not a complete shutdown, battery still drains).
  • [Auto Wake-Up]: Enable/disable auto wake-up.
  • [Wake-Up Timer]: Device wakes up and returns to normal operation when set wake-up timer is reached.

8. Specifications

General
Radio FM64-108MHz
Shortwave (SW)2.3-30MHz
Medium Wave (MW)520-1710KHz
Long Wave (LW)153-279KHz
RX Frequency Range18-620MHz, 840-1000MHz
TX Frequency Range18-32MHz, 136-174MHz, 400-520MHz
Channel Capacity1024 Channels + 3 VFO Channels
Channel Spacing (W/N)Analog: 25kHz/12.5kHz, Digital: 12.5K
Voltage7.4V DC
Working ModeSame frequency simplex, different frequency simplex
AntennaRemovable Antenna
Frequency Stability±2.5ppm
Working Temperature-20°C ~ +60°C
Dimension149 * 64 * 37 mm (approx. 307g)
Transmitting Part
Modulation ModeF3E
Maximum Frequency Deviation (W/N)≤5KHz / ≤2.5KHz
SNR (W/N)-45dB / -40dB
TX Current<2500mA
Receiving Part
Sensitivity (W/N)0.22μV/0.25μV (12dB SINAD)
Intermodulation (W/N)65dB / 60dB
Audio Distortion<5%
Audio Output Power<1W (16Ω)
RX Current≤350mA
Standby Current≤100mA

Note: Specifications are subject to change due to technical improvements without prior notice or liability.

9. Maintenance

  • Cleaning: Use a soft, damp cloth to clean the radio's surface. Do not use harsh chemicals or abrasive cleaners.
  • Battery Care: Charge the battery fully before first use. Avoid overcharging or completely draining the battery to prolong its lifespan. Store the radio and battery in a cool, dry place when not in use for extended periods.
  • Antenna: Ensure the antenna is securely attached. Do not operate the radio without an antenna, as this can damage the transmitter.
  • Storage: Store the walkie talkie in a dry, dust-free environment away from extreme temperatures.

Charging Methods

Image showing multiple charging methods for the walkie talkie
The BAJETON BJ-98PLUS supports both a dedicated base charger and a universal Type-C charger.

The radio can be charged using the provided base charger or a standard Type-C cable. The indicator light will show red when charging and green when fully charged.

10. Troubleshooting

  • No Power: Check if the battery is properly installed and charged. Ensure the ON/OFF volume knob is turned on.
  • Cannot Transmit or Receive: Verify that the frequency is correctly set and within the operating range. Check antenna connection. Ensure the PTT button is functioning.
  • Poor Audio Quality: Adjust the squelch level. Check MIC and SPK gain settings. Ensure you are within range of other radios.
  • Intermittent Calls: If receiving signals from devices with a large frequency offset, increase the [Adjacent Channel Limitation] setting.
  • Device Emits Abnormal Odor: Immediately turn off the device and disconnect power. Do not attempt to use it again until it has been inspected by a qualified technician.
  • Device Unresponsive (Stunned/Killed): If the device was remotely stunned or killed via DTMF, it will require the correct DTMF wake code to restore functionality. Ensure you have recorded your wake code.
  • Sharp Sound in SSB Mode: Adjust the BFO (Beat Frequency Oscillator) frequency. Lower it if the sound is sharp, increase it if the sound is too deep.

11. User Tips

  • For optimal performance, always use the correct antenna for the selected frequency band.
  • Familiarize yourself with the custom key functions to quickly access frequently used features.
  • Regularly check the battery level, especially before extended use.
  • When using the cross-band repeater, be aware that Channel C is disabled.
  • If experiencing interference, try adjusting the [Receive Signal Strength Refresh Time] to a larger value.

12. Support & Warranty

For technical support, warranty claims, or further assistance, please contact your local distributor or the BAJETON customer service. Refer to the Guarantee Card included with your product for specific warranty terms and conditions.

A detailed user manual in PDF format is available for download. You can find it at: BAJETON BJ-98PLUS User Manual (PDF).

© 2024 BAJETON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.