Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Burhui LED Tree Hugging Lamp. Please read this manual thoroughly before installation and retain it for future reference.
Important Safety Information
- Installation should be performed by a professional electrician to ensure correct and firm wiring.
- Connect only to the rated voltage range of AC85-265V. Connecting to other voltages (e.g., 380V) can cause overvoltage damage and prevent the light from illuminating.
- Do not immerse the light unit in water. While the light unit itself has an IP65 waterproof rating (resistant to rain and water splashes), the wiring connections are not inherently waterproof and require additional waterproofing measures.
- Do not perform wiring or power-on operations with bare hands in rainy or humid conditions to prevent electric shock.
- Never operate the light with wet hands.
- Do not forcibly disassemble or modify the lamp.
- Never pull, bend, or crush the lamp's power cord to prevent insulation damage, exposed conductors, short circuits, or electric shock.
- Install the lamp out of children's reach to prevent accidental contact, cord pulling, or unplugging.
WARNING: This product is for electrical connection only, not solar powered.
Product Features and Specifications
- Product Name: Tree Hug Light
- Input Voltage: AC85-265V
- Waterproof Rating: IP65 (resistant to rain and water splashes)
- Light Source Type: LED Light Source
- Beam Angle: 30 degrees
- Main Material: Aluminum
- Luminous Flux: 249-2000 (depending on configuration)
- Power Source: DC (internal conversion from AC input)
- Outdoor Lighting Type: Spotlights, Landscape lighting
- Recommended Applications: Outdoor tree decoration, courtyard lighting, scenic area illumination, festive decoration.
Available Configurations and Power Output:
| Inner Ring Diameter | Number of Individual Sections | Power | Voltage |
|---|---|---|---|
| 210mm / 8.26 inch | 4 pcs | 48W | 85V-265V |
| 310mm / 12.2 inch | 5 pcs | 60W | 85V-265V |
| 380mm / 14.96 inch | 6 pcs | 72W | 85V-265V |
| 440mm / 17.32 inch | 7 pcs | 84W | 85V-265V |
Note: The data is manually measured, and slight errors are normal.
Figure: Product Configurations and Specifications
Component Details:
Figure: Aluminum Housing, LED Beads, and Waterproof Connector
Figure: Key Features - Spliceable Ring, IP65 Waterproof, Tempered Glass
Package Contents (for 1pc section)
Figure: Components for a Single Light Section
- LED Tree Hugging Light Section (Quantity varies by model)
- Waterproof Plug (x1 per section)
- Connection Block (x1 per section)
- Power Line (x1 per unit/set)
- Screws (x4 per section)
Setup and Installation
Refer to the installation video and diagrams for visual guidance. Ensure all safety precautions are followed.
Video: Installation Steps and Lighting Demonstration
Step-by-Step Installation:
- Install the Connection Block:
Arrange the individual light sections in a circular shape around the tree. Use a screwdriver to install the connection blocks and fix them securely between the two adjacent light sections using the provided screws.
Figure: Step 1 - Installing Connection Block
- Connect the Power Cords:
Connect the power cords between the light sections. Ensure the waterproof plugs are securely connected to form a continuous circuit.
Figure: Step 2 - Connecting Power Cords
- Connect to External Power:
Connect the external power cord to the assembled light ring. Ensure the waterproof cover is properly secured over the connection point. For the remaining two wires, one connects to the waterproof cap and the other to the hard wire (main power supply).
Figure: Step 3 - Connecting External Power
Remember: All wiring connections must be properly sealed and waterproofed, as the IP65 rating applies only to the light unit itself, not the wiring connections.
Operating Instructions
Once properly installed and connected to a power source within the AC85-265V range, the light will illuminate. The light can display various colors, including warm white, white, and colorful lighting.
Figure: Warm White and White Light Illumination
Figure: Colorful Lighting Options and Switch Control
If your model includes a controller or switch for color selection, use it to cycle through the available lighting modes (e.g., warm white, white, red, green, blue, purple, etc.).
Maintenance
- Regularly inspect the power cord and connections for any signs of wear, damage, or loose fittings.
- Keep the light unit clean from dirt and debris to ensure optimal performance and light output. Use a soft, damp cloth for cleaning.
- Ensure the drainage port on the lamp housing is clear of obstructions to allow any accumulated water to drain.
- Do not use harsh chemicals or abrasive materials for cleaning, as this may damage the aluminum housing or tempered glass cover.
Troubleshooting
- Light fixture does not light up:
- Check if the wiring is loose. Secure all connections.
- Inspect the power line for damage or core breakage. Replace if necessary.
- Ensure the power switch is turned on.
- Light fixture is slightly bright and flickering:
- Check for loose wiring or poor contact. Re-secure connections.
- Verify that the connected voltage is consistent with the product's input voltage range (AC85-265V).
- Water intrusion into lamp housing:
This product has an IP65 waterproof rating, meaning it is resistant to rain and water splashes, but submersion in water is strictly prohibited. If water enters the lamp, drain it via the designated drainage port on the lamp housing.
User Tips
- The light is designed for electrical connection and is not solar-powered. Ensure a stable AC power source is available.
- The wide voltage range (85-265V) makes it compatible with various electrical systems, including 110V.
- For optimal aesthetic effect, consider the beam angle and placement to highlight tree trunks or specific landscape features.
Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the seller's policies or contact their customer service directly. Keep your purchase receipt as proof of purchase.
A user manual in PDF format is also available for download: View User Manual (PDF)
Recommended Applications
The Burhui LED Tree Hugging Lamp is ideal for enhancing the ambiance of various outdoor settings:
- Courtyards: Create inviting and well-lit outdoor living spaces.
- Lawns: Highlight trees and shrubs, adding depth and visual interest to your garden.
- Parks: Illuminate pathways and natural features for safety and beauty.
- Squares: Enhance public spaces with decorative and functional lighting.
- Wayside: Provide subtle illumination along paths and driveways.
- Festive Decoration: Use colorful lighting options to create a festive atmosphere for special occasions.
Figure: Versatile Outdoor Applications