IKSLED Sweep Sensor 3410

Contents

IKSLED Mini Hand Scan Switch Module Instruction Manual

Model: Sweep Sensor 3410

1. Product Features

  • No delay, instant response
  • Strong anti-interference, stable and reliable performance
  • Supports high-power loads, with a maximum current of 3A
  • High sensitivity design, sensing distance of 3-8cm
  • Supports dimming function with brightness memory
Overview of three IKSLED Hand Scan Switch Modules
Figure 1: Overview of the Hand Scan Switch Module, highlighting its features.

2. Technical Specifications

Parameter Value
Input Voltage DC 3.7V-24V (Constant voltage power supply)
Max Current 3A
Load Power Max. 60W
Sensing Distance 3-8 cm
Operating Modes Hand wave switch / Door control switch
Indicator Light Blue indicator light
Material Plastic
Certification RoHS, LVD, EMC, CE, CCC
Diagram showing dimensions of two types of switch sensors
Figure 2: Switch size comparison. The functions are the same, only the sensing heads differ.

3. Installation Instructions

  1. Ensure the power is disconnected before wiring.
  2. Do not block the sensor probe during installation to avoid affecting sensing performance.
  3. Connect the sensor and lamp according to the wiring diagram below.

Wiring Diagram

Input Power: DC 3.7V - 24V constant voltage power supply (V+/V-)

Wiring diagram for the hand scan switch module
Figure 3: Wiring diagram showing connection from power adapter to sensor and LED lamp. The input voltage must be a constant voltage power supply DC3.7-24V.
Installation demonstration showing the blue indicator light and sensor probe
Figure 4: Installation demonstration. Note the blue indicator light and the sensor probe. Do not block the sensor probe during installation.

4. Operating Mode Description

Type A: Hand Wave Dimming Mode

  • Wave hand once: Light turns on.
  • Wave hand again: Light turns off.
  • Hold hand near the sensor: Adjust brightness (brightness memory function included).
Hand wave operation demonstrating 3-8cm sensing distance
Figure 5: Hand wave operation. A simple scan turns it on or off. Sensing distance is 3-8cm.
Hand scanning to light up, showing 8cm distance
Figure 6: Light activates when scanned by hand, no physical touch required.

Type B: Door Control Mode

  • Door opens: Light automatically turns on.
  • Door closes: Light automatically turns off.
Function Type A and Type B descriptions
Figure 7: Visual explanation of Type A (Hand Wave) and Type B (Door Control) functions.

Video 1: Demonstration of Hand Wave and Door Control functions.

5. Precautions

  • The input voltage must be DC constant voltage. Do not connect to AC power.
  • Do not use in high temperature, humid, or strong magnetic field environments.
  • Sensing distance may be affected by ambient light and installation position. It is recommended to install on a flat surface.
  • The controller is only used for switch control of LED lamps, not for live inductive loads (such as inductive motors, relays, etc.).
  • If any malfunction occurs, please check if the power supply voltage meets the requirements.

6. Troubleshooting

If the switch module is not functioning as expected, please review the following:

  • No Power/Light Not Turning On: Verify that the input voltage is within the specified DC 3.7V-24V range and is a constant voltage supply. Ensure all wiring connections are secure and correct according to the wiring diagram.
  • Inconsistent Sensing: Check for any obstructions near the sensor probe. Ambient light conditions or the installation position might affect sensing distance; try adjusting the position or ensuring a flat installation surface.
  • Dimming Not Working: Ensure you are holding your hand near the sensor for a continuous period to activate the dimming function.
  • Unexpected Behavior: Confirm that the module is only connected to LED lamps and not to inductive loads like motors or relays.

For further assistance, refer to the official user manual PDF if available, or contact customer support.

7. Warranty Information

This IKSLED Hand Scan Switch Module comes with a 1-year warranty from the date of purchase. The warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

© 2024 IKSLED. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.