RveTee 1F0240-gy

Contents

RveTee 3D Peel and Stick Wall Cushions Instruction Manual

Model: 1F0240-gy

1. Product Overview

The RveTee 3D Peel and Stick Wall Cushions are designed to provide both decorative appeal and protective functionality for your walls. These anti-collision panels are ideal for use as bed headboards, in game rooms, or any area requiring a soft, protective surface. They feature a simple peel-and-stick installation method, requiring no screws or additional hardware.

2. Safety & Warnings

  • Warning: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • ATTENTION: Only for domestic use.

3. Setup and Installation

These wall cushions are designed for quick and easy installation without the need for tools or hardware.

Person installing a grey peel and stick wall cushion onto a wall next to pink cushions.

Figure 3.1: Peel and Stick installation in minutes, no screws or hardware needed.

Close-up of the strong adhesive backing being peeled off a wall cushion.

Figure 3.2: The cushions come with strong adhesive backing for easy application.

Installation Steps:

  1. Prepare the Surface: Ensure the wall surface is clean, dry, and smooth. Remove any dust, grease, or loose paint for optimal adhesion.
  2. Measure and Plan: Before peeling, arrange the cushions on the floor or temporarily hold them against the wall to plan your desired layout and ensure proper alignment.
  3. Peel Off the Backing Paper: Gently peel the sticker from the backing paper, starting from one corner. Avoid touching the adhesive side with your hands to prevent fingerprints or reduced adhesion.
  4. Position and Paste: Align the cushion with your planned guide lines on the wall. Gently attach one corner of the cushion to the wall first. Slowly smooth the cushion from this corner to the other side with your hand, ensuring no bubbles are trapped.
  5. Remove Bubbles (if any): If air bubbles appear, use a credit card or a squeegee (wrapped with a soft cloth to avoid scratching the cushion) to press the cushion firmly from the center towards the edges. This helps squeeze out air bubbles and ensures tight adhesion to the wall.

4. Operating and Usage

Once installed, the wall cushions serve multiple purposes:

  • Protective Barrier: Acts as an anti-collision layer, protecting walls from impacts and providing a softer surface in children's rooms or play areas.
  • Headboard Alternative: Can be arranged to create a comfortable and stylish headboard for beds.
  • Decorative Element: Enhances room aesthetics with its 3D design and various color options.

5. Maintenance

The wall cushions are made from waterproof leather, making them easy to clean and maintain.

Hand wiping a spill off a grey waterproof leather wall cushion.

Figure 5.1: Waterproof leather allows for easy cleaning with a single wipe.

Cleaning Instructions:

  • For spills or dirt, simply wipe the surface with a damp cloth.
  • Avoid using abrasive cleaners or harsh chemicals, as these may damage the material.
  • For stubborn stains, a mild soap solution can be used, followed by wiping with a clean, damp cloth.

6. Troubleshooting

Common Issues and Solutions:

  • Panels Arrived with Wrinkles/Creases: Some users have reported panels arriving with creases due to packaging. While some minor creases may flatten over time, significant wrinkles might persist. Ensure proper smoothing during installation. Gentle, indirect heat (e.g., from a hairdryer on a low setting, held at a distance) might help relax the material, but proceed with caution to avoid damage.
  • Poor Adhesion: If panels are not sticking well, ensure the wall surface was thoroughly cleaned, dry, and smooth before application. Adhesion may be compromised on textured, dusty, or greasy surfaces.
  • Air Bubbles After Installation: If bubbles appear, gently lift the edge of the cushion closest to the bubble and reapply, smoothing it down with a squeegee or credit card from the center outwards.

7. Specifications

Diagram showing dimensions of a wall cushion: 50cm length, 23cm width, and 10mm thickness.

Figure 7.1: Product dimensions and thickness.

AttributeDetail
Product NameWall Stickers / Wall Cushions
BrandRveTee
Model1F0240-gy
MaterialXPU+PU Leather
Panel Dimensions (each)50 cm (19.68 inches) Length x 23 cm (9.05 inches) Width
Thickness10 mm
Quantity per Pack5 Wall Cushions
Pattern Type3D Sticker
OriginMainland China
Package Weight0.45 kg
Package Dimensions50 cm x 23 cm x 10 cm

8. User Tips

  • Surface Preparation is Key: For the best and longest-lasting adhesion, always ensure your wall surface is perfectly clean, dry, and smooth before applying the panels.
  • Handle with Care: While installing, try to avoid bending the panels excessively to minimize the risk of creating new creases.
  • Layout First: Always plan your layout on the floor or with temporary placement before peeling the adhesive backing. This helps ensure a symmetrical and desired final look.

9. Warranty and Support

For any product inquiries, support, or warranty claims, please contact your seller directly. Provide your order details and product model number (1F0240-gy) for faster assistance.

Manufacturer: Harbin Qingxuan Trade Co.Ltd
EU Authorized Representative: Synertrade FR SAS

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.