1. Introduction
This manual provides comprehensive instructions for the installation, operation, and troubleshooting of your ANYFAR Wireless CarPlay and Android Auto Adapter Module. This device seamlessly integrates Apple CarPlay and Android Auto functionalities into your Mercedes-Benz vehicle's existing NTG 5.0 or 5.1 COMAND system, allowing for wireless connectivity without altering the original display.
2. Product Features
- Wireless & Wired CarPlay: Enjoy full Apple CarPlay functionality, including navigation, music, calls, and Siri voice control, via wireless or wired connection.
- Wireless & Wired Android Auto: Access Google Maps, Spotify, calls, and Google Assistant voice control through wireless or wired Android Auto.
- Front/Rear/360 Camera Input: Supports aftermarket front, rear, and 360-degree cameras with intelligent dynamic trajectory display and radar support.
- Retains Original Car Functions: Seamlessly integrates with your vehicle's steering wheel controls, central control panel, and original microphone.
- Bluetooth Audio Output: Utilizes the factory car Bluetooth for audio output, reducing interference and providing faster sound response.

Image: Wireless CarPlay and Android Auto in operation, with the adapter module.
3. Compatibility
This module is compatible with Mercedes-Benz vehicles equipped with NTG 5.0 and 5.1 COMAND systems. Please refer to the table below to confirm your vehicle's compatibility.

Image: Compatible Mercedes-Benz Model List for NTG 5.0 & 5.1.
Compatible Model List (Mercedes-Benz NTG 5.0 & 5.1)
| Car Model | Years | Screen Size |
|---|---|---|
| CLA/CLS/GLA/GLE/A/B/SLC/GLS | 2015-2017 | 7/8 inch |
| C180/C200/GLC/V Class | 2015-2017 | 7/8 inch |
| V260/AMG C63 | 2017 | 8.3 inch |
| AMG GT | 2018 | 8.3 inch |
| S Class | 2013-2016 | 10.25 inch |
| Aston Martin DB11 | 2019 | 7 inch |
4. Setup and Installation
Important: Professional installation is highly recommended. Ensure the vehicle's battery is disconnected before beginning installation to prevent electrical damage.
4.1 Wiring Diagram
Follow the diagram below for connecting the ANYFAR module to your vehicle's existing wiring harness and display unit.

Image: Installation wiring diagram for the ANYFAR module.
4.2 DIP Switch Settings
DIP switch settings are crucial for proper functionality and vary by vehicle model and screen size. Please consult the specific DIP switch configuration for your Mercedes-Benz NTG 5.0/5.1 system. Incorrect settings can lead to display issues or non-functionality. After changing DIP settings, reboot the decoder box to apply changes.
4.3 Rear View Camera Input Setup
The module supports aftermarket rear view cameras. Connect the camera as shown in the wiring diagram below.

Image: Rear view camera wiring diagram.
System Settings for Rear Camera and Trajectory
- Enter system settings: Click "Factory mode" > "Advanced mode".
- Enter password "888888".
- Navigate to "MCUsetup" and uncheck the "AO" option.
- Return to the previous level and click "Restart system" to enable the reversing rear view function.
- For reversing trajectory lines, uncheck the "A1" box. For aftermarket radar, uncheck the "A2" box.

Image: System settings for rear camera, radar, and trajectory.
4.4 AUX Output Setup (If Bluetooth is Unavailable)
If your car does not have Bluetooth functionality, you can use the AUX sound output.
- Connect the AUX cable to your car and select "AUX" in the NTG system.
- In the module's settings, navigate to
Settings > Factory Settings > Phone link Settings. - Set "Disable phonelink Audio" to
ON. - Go back and save the settings. A reboot is necessary for the changes to take effect.

Image: AUX output configuration in module settings.
5. Operating Instructions
5.1 Wireless CarPlay Connection
- Ensure your iPhone's Bluetooth and Wi-Fi are turned on.
- On your iPhone, go to Bluetooth settings and select the device named "CAR Audio XXXX".
- Confirm the pairing request and allow the use of CarPlay when prompted.
- Ensure your vehicle's audio system is set to Bluetooth music mode for optimal audio performance.

Image: Wireless CarPlay connection steps on iPhone.
5.2 Wireless Android Auto Connection
- Ensure your Android phone's Bluetooth and Wi-Fi are turned on.
- On your Android phone, go to Bluetooth settings and select the device named "CAR Audio XXXX".
- Confirm the pairing request.
- Follow any on-screen prompts on your phone and car display to complete the Android Auto connection.

Image: Wireless connection overview.
5.3 Control Functions
The module retains the use of your original car controls for seamless interaction.
Steering Wheel Buttons
| Button | Operation | Function |
|---|---|---|
| Call (Answer/End) | Long press | Switch between OEM screen and interface screen |
| Call (Answer/End) | Short press | Hang up the phone |
| Call (Answer/End) | Short press | Answer the phone |
| Volume + | Short press | Increase volume |
| Volume - | Short press | Decrease volume |
Central Control Panel (COMAND Controller)
| Control | Operation | Function |
|---|---|---|
| Back Button | Long press | Switch between OEM screen and interface screen |
| COMAND Knob | Swipe/Click | Control function (navigation, selection) |
| Hazard Light Button | Double Click | Switch between OEM screen and interface screen |
6. Maintenance
- Keep the module dry and clean. Avoid exposure to liquids or excessive moisture.
- Do not expose the module to extreme temperatures (hot or cold).
- Ensure the module is installed in a location with adequate ventilation to prevent overheating.
- Avoid using harsh chemicals or abrasive cleaners on the module. Use a soft, dry cloth for cleaning.
7. Troubleshooting
Common Issues and Solutions
- Bluetooth Disconnects: This is normal. After initial Bluetooth pairing, a Wi-Fi connection is established to transmit data, and the Bluetooth connection will disconnect to avoid interference.
- Cannot Connect CarPlay, but Bluetooth is Paired: Forget the device's Bluetooth connection on your iPhone. Then, reset your iPhone's Wi-Fi settings:
Settings > General > Transfer or Reset [Device] > Reset > Reset Network Settings. - Unstable Wireless CarPlay Connection:
- Ensure the module's mounted position is not blocked by metal components, as this can impair Wi-Fi signal transmission.
- Switch the Wi-Fi channel in the module's settings:
Factory Mode > Connectivity Settings > Hotspot Band. Select channel 1, 6, or 11, depending on your region and local interference.
User Tips from Experience
- OEM Microphone Integration: If your vehicle does not have an optical bus, ensure the "mic in" and "mic out" cables are connected to receive the OEM microphone input.
- Original Front Camera: To get the original front camera working correctly, you may need to adjust the camera delay time in the module's settings.
- Optimal Audio: Always ensure your car's audio system is set to Bluetooth music mode for the best sound quality and connection stability with the module.
8. Specifications
- Product Type: Wireless CarPlay & Android Auto Adapter Module
- Compatibility: Mercedes-Benz NTG 5.0 & 5.1 COMAND Systems
- Connectivity: Wireless (Wi-Fi, Bluetooth), Wired (USB)
- Inputs: Front Camera, Rear Camera, 360 Camera
- Package Dimensions: 27 cm (Length) x 20 cm (Width) x 12 cm (Height)
- Package Weight: 0.843 kg
9. Frequently Asked Questions (FAQ)
- Q: Is this compatible with a Mercedes GLC 2016?
- A: Yes, according to the compatibility list, Mercedes GLC models from 2015-2017 are compatible with this module.
- Q: Is this compatible with a Mercedes CLA W117 from 2014 with NTG51?
- A: The compatibility list indicates CLA models from 2015-2017 are compatible. While your NTG version is 5.1, please double-check if your specific 2014 model falls within the supported range or if an early 2015 model year applies.
10. Warranty and Support
For warranty information, technical assistance, or further support, please refer to your original purchase documentation or contact the seller directly. Keep your proof of purchase handy for any warranty claims.