AceGamer T52L

Contents

AceGamer Mobile Gaming Controller T52L User Manual

Model: T52L

1. Introduction

This manual provides detailed instructions for the AceGamer Mobile Gaming Controller, Model T52L. This wired stretch mobile controller features Hall Effect triggers and Hall Effect rockers, designed to enhance your mobile gaming experience. It is compatible with a wide range of Android and iOS devices.

For a comprehensive guide, you may also refer to the official user manual PDF: User Manual (PDF)

AceGamer Mobile Gaming Controller with phone inserted, showing included accessories (Type-C cable, D-pad, rocker caps).

Figure 1: AceGamer Mobile Gaming Controller and Accessories

2. Setup

2.1. Compatibility

The AceGamer Mobile Gaming Controller is compatible with:

  • Android Devices: Type-C port Android devices running Android 8.0 and above.
  • iOS Devices: Type-C port Apple devices (iPhone 15 series) running iOS 14 and above.

Important Notes:

  • Not compatible with Android phones using Micro USB interface, tablets, Nintendo Switch, Lightning iPhones, iPad, Apple TV, iPod, or Fire TV/TV Box.
  • The controller supports phone lengths between 105mm and 190mm.
  • It is suggested to avoid phone cases thicker than 1mm for optimal fit.
Detailed diagram of the controller's buttons and ports, highlighting compatible platforms (Android, iOS) and phone length range (105-190mm). Also notes to avoid thick phone cases.

Figure 2: Controller Layout and Compatibility

2.2. Physical Connection

  1. Align the Type-C plug connector of the controller with the charging port of your mobile phone.
  2. Gently pull open the controller to insert your mobile phone.
  3. Close the controller to secure the phone and complete the connection.

The controller supports up to 9V/3A charging, allowing your phone to be charged and played at the same time. Ensure your phone and charger support PD2.0 and above protocol for this feature.

2.3. GameMacro APP Installation

For advanced settings and customization, you can use the GameMacro APP:

  • Android Systems: Search for and install "GameMacro" directly from the Google Store.
  • Apple Systems: Search for and install "GameMacro" from the Apple Store.

After successful connection, open your phone's Bluetooth list, and "GameMacro" will appear. Select it to connect and pair.

2.4. D-pad Replacement

The controller features a replaceable D-pad. To change it, gently remove the existing D-pad and place the desired one in its position.

Features like Silicon Design, Adaptive Type-C Connector, Replaceable D-pad, and Non-Slip & Ergonomic design. Also notes that the charging port only provides charging, no data sync.

Figure 3: Replaceable D-pad and other features

3. Operating Instructions

3.1. Mode Switching

To switch between operating modes, press and hold the View + Menu buttons for 2 seconds. The LED indicators will show the current mode:

  • Android HID Mode: Left and right LEDs indicate blue.
  • X-INPUT Mode: Left and right LEDs indicate green.
  • PS4 Streaming Mode: Left and right LEDs indicate purple. This mode supports iOS devices with a Type-C female socket (iPhone 15 series) for PS4 streaming. If the LEDs are solid purple, the connection is successful, and the controller will be automatically recognized.

3.2. Macro Programming

The controller supports macro programming for custom key combinations.

  1. Macro Programming Setting: While the controller is connected, press and hold TURBO + M1 (or M2) for 2 seconds. The left and right LEDs will flash slowly in their current color, indicating entry into programming mode.
  2. Perform the desired button sequence (e.g., left joystick movements, cross buttons, A, B, X, Y, LB, RB, LT, RT, L3, R3).
  3. Press M1 (or M2) to save the macro. The LEDs will return to their previous state.

A maximum of 24 buttons can be programmed at a time. Any buttons entered beyond the indicator flash prompts will not be saved. Programmed functions are retained after shutdown and restart. Factory default for M1 is 'A' and M2 is 'B'.

3.3. M1, M2 Key Mapping

To map a single function key to M1 or M2:

  1. While connected, press and hold TURBO + M1 (or M2) for 2 seconds until the LEDs flash slowly.
  2. Press the desired function key you wish to map.
  3. Press M1 (or M2) again. The LEDs will return to their previous state, and the M1/M2 key will now be mapped to that function.
Illustration of Macro Programming (M1/M2 keys with up to 24 keys) and 3 Turbo Speeds (5, 12, 20 shots/s).

Figure 4: Macro Programming and Turbo Speeds

3.4. Turbo Function

The Turbo function can be applied to A, B, X, Y, LB, RB, LT, and RT buttons.

  1. Manual Turbo: Hold down the Turbo key, then press the desired function key. The key will now activate Turbo when held down during gameplay.
  2. Auto Turbo: Press the above key combination a second time. The key will automatically activate Turbo when pressed during gameplay.
  3. Cancel Turbo: Press the key combination a third time to cancel the Turbo function for that key.
  4. Adjust Turbo Speed: Press and hold the Turbo button, and simultaneously move the right 3D joystick up or down. There are three speed settings:
    • Fast: 20 times per second
    • Medium: 12 times per second
    • Slow: 5 times per second

When a key triggers Turbo, the left and right LEDs will flash according to the Turbo speed. Turbo settings are not saved after power off; the default is no Turbo function, and the default Turbo speed is 12 times per second.

3.5. Lighting Adjustment

The rocker aperture light effect adjusts with the joystick's offset. Brightness has 10 grades, directly proportional to the distance the rocker is moved. At the center (no operation), all LEDs maintain the lowest brightness. The light effect of the last setup is saved after restarting the controller. Factory default is white light at 70% brightness.

  • Light Mode Switching: Press Turbo + LED key.
  • Dazzle Color Mode: Features a color flow effect with seven colors.
  • Monochrome Mode: (Factory default: white) Eight colors can be switched (light white, red, orange, yellow, green, cyan, blue, purple).
  • Rocker Mode: Dazzle mode and eight colors can control LED brightness.
  • No Light Mode.
  • Light Color Switching: Short press the LED key.
Customization options for RGB Light Effects (Dazzle Mode, Monochrome Mode, Light off Mode) and Dynamic Brightness Adjustment.

Figure 5: RGB Light Effects Customization

3.6. ABXY Key Value Interchange

To swap the A/B X/Y key values (e.g., between Switch and Xbox layouts):

  1. Press and hold Turbo + Screenshot button for 3 seconds.
  2. The left and right LEDs will blink the current color 3 times fast.

This setting is not saved. The factory default for the controller is the XBOX layout.

Mechanical Microswitch Buttons (millisecond trigger, zero delay, super long life) and ABXY Key Value Interchange (Switch/Xbox layout exchange).

Figure 6: Mechanical Microswitch Buttons and ABXY Key Value Interchange

3.7. Rocker and Trigger Calibration

If you experience issues with joystick or trigger accuracy, perform calibration:

  1. Connect your mobile phone to the controller.
  2. Press and hold the View + Menu + HOME buttons for 3 seconds. The left and right LEDs and joystick light will change to white blinking, indicating entry into calibration mode.
  3. Ensure the joystick and triggers are in their initial, untouched state. Press the "A" key.
  4. Rotate both the left and right joysticks at their maximum angle for 3 full turns, then release them to return to their natural initial position.
  5. Press both the left and right trigger buttons 3 times at maximum travel, then release them to return to their natural initial position.
  6. Press the "A" key to finish and exit calibration mode. The LEDs and joystick lights will return to their previous state.

3.8. Rocker Adjustment Without Dead Zone

To turn off the joystick deadband:

  • Use the key combination: Turbo + downward pressure on the corresponding joystick (L3 or R3).

The indicator on the side of the joystick will flash twice at 2Hz to confirm the setting of no deadband mode. This setting is not saved and defaults to deadband mode upon restart.

3.9. Quick Trigger Mode

To set quick trigger mode:

  1. Press and hold Turbo + Menu for three seconds. The lights on both sides of the triggers will flash at 2Hz for one second.
  2. In fast trigger mode, the trigger function is out of action when the trigger reaches 30% travel, meaning there is no linear function.

This setting is not saved, and the default is that the trigger has a linear function.

3.10. Factory Reset

To perform a factory reset:

  1. Connect the controller to your mobile phone.
  2. Press and hold the View + Menu + Turbo keys for 3 seconds.
  3. The left and right LED lights and joystick lights will turn to red fast flash from their current state. The controller will complete the factory reset.

The following functions will be restored to factory settings:

  • M1 and M2 keys are restored to M1=A, M2=B.
  • Rocker light ring is restored to light on with 70% brightness and white light always on.

NOTE: The factory reset operation does not clear the rocker and trigger post-calibration data.

4. Maintenance

To ensure the longevity and optimal performance of your AceGamer Mobile Gaming Controller, please follow these maintenance guidelines:

  • Cleaning: Wipe the controller with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
  • Storage: Store the controller in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Handle the controller with care. Avoid dropping it or subjecting it to strong impacts.
  • Disassembly: Do not attempt to disassemble the product. Unauthorized disassembly may cause damage and void any potential support.
  • Environmental Exposure: It is strictly prohibited to expose the product to fire or water to prevent damage or explosion.

5. Troubleshooting

If you encounter issues with your controller, refer to the following common problems and solutions:

5.1. Connection Issues

  • Controller not recognized: Ensure your phone's operating system meets the minimum requirements (Android 8.0+, iOS 14+ for iPhone 15 series). Verify the Type-C connection is secure. Try restarting your phone and the controller.
  • LEDs not indicating correctly: Refer to the "Mode Switching" section (3.1) to ensure the correct mode is selected and indicated by the LEDs. If issues persist, perform a factory reset (3.10).
  • "Connection Error" during gameplay: This can occur due to unstable network connections or game-specific issues. Try restarting the game or checking your internet connection.
A screenshot of a phone displaying a 'Connection Error' message while using the controller, indicating a potential troubleshooting scenario.

Figure 7: Example of a 'Connection Error' message

5.2. Button/Joystick Malfunctions

  • Inaccurate joystick/trigger response: Perform the "Rocker and Trigger Calibration" procedure (3.7).
  • Programmed functions not working: Ensure the macro programming was saved correctly (3.2). If not, clear the programming and re-program.
  • Turbo function not active: Remember that Turbo settings are not saved after power off. Re-activate the Turbo function as described in section 3.4.

5.3. Game-Specific Notes

  • Under iOS mode, the controller supports 'Genshin Impact' but does not support 'PUBG Mobile'.
  • Under Android mode, neither 'Genshin Impact' nor 'PUBG Mobile' are supported.
  • In 'Call of Duty' gaming interface, if prompted to choose a controller model (PS4, PS5, or Xbox), select XBOX.

6. Specifications

FeatureDescription
Brand NameAceGamer
Model NumberT52L (also referred to as C16)
TypeGamepads
Interface TypeType-C
Compatible PlatformAndroid, iOS
Compatible Brand/ModelMobile Device (Android Smartphones, iPhone 15 Series)
Joystick Sensor ModuleHall Effect
Trigger Button TypeLinear
D-pad Switch TypeMICRO SWITCH
Bumpers Switch TypeMICRO SWITCH
Battery IncludedNo
Wear-resistant joysticksNo
PackageYes
OriginMainland China
Dimensions (L*W*H)240mm * 130mm * 57mm
Weight0.38 kg
Charging Support9V/3A (via controller, requires PD2.0+ protocol)
Compatible Phone Length105mm - 190mm

7. User Tips

  • For optimal fit and connection, avoid using phone cases thicker than 1mm.
  • If you plan to charge your phone while playing through the controller, ensure both your phone and charger support the PD2.0 or higher fast charging protocol.
  • When playing 'Call of Duty' and prompted to select a controller model, choose XBOX for compatibility.
  • Be aware of game-specific compatibility: 'Genshin Impact' is supported on iOS but not Android. 'PUBG Mobile' is not supported on either iOS or Android with this controller.
  • The controller feels sturdy and works well for many Android devices, including the Poco F7.

8. Warranty and Support

For any issues, questions, or support needs regarding your AceGamer Mobile Gaming Controller T52L, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific warranty terms and contact information.

For further assistance, you can also consult the full user manual available as a PDF document: User Manual (PDF)

9. Product Demonstration Video

Video: A product demonstration showcasing the controller's features, phone insertion, gameplay, and button functionalities.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.