1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your new Motorcycle Fog Lights Headlight Lamp. Please read this manual thoroughly before use and retain it for future reference.
2. Important Safety Information
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep the product and its small accessories (connector terminals, fixing clips, screws) out of reach of children under 3 years old to prevent choking hazard and electric shock risk.
- Cut off the motorcycle's 12V power supply (disconnect the battery negative electrode) before installation and disassembly; do not connect the product to the power supply with bare hands to avoid short circuit and electric shock.
- Inspect the product for damage (shell cracks, wire breakage, lamp bead damage, connector deformation) before installation; do not use damaged products to avoid circuit failure and fire hazards.
- Do not expose the product to water, moisture, heavy rain or high humidity environments for a long time; the product is splash-proof (IP67) but not fully waterproof, and do not immerse it in water.
- Do not touch the lamp bead directly with bare hands; finger grease will cause the lamp bead to overheat and burn out, and use clean dry cloth or tweezers to take the lamp body if necessary.
- Ensure the product is firmly fixed after installation; do not let the lamp body and wires contact the motorcycle's high-temperature parts (exhaust pipe, engine) to avoid wire melting and fire.
- Do not adjust the product's light angle to affect the driving vision of oncoming vehicles; the light adjustment must comply with local traffic regulations.
- This product is not a toy; it is strictly forbidden for children to play with the product and its accessories to avoid electric shock and other safety accidents.
- Avoid looking directly into the beam; the high-intensity LED light can cause permanent eye damage.
3. Specifications
| Feature | Detail |
|---|---|
| Product Name | Motorcycle Fog Lights Headlight Lamp |
| Model | BWDTZ04 |
| Item Type | Headlight Assembly |
| Voltage | DC12V |
| Waterproof Rating | IP67 (Splash-proof, not fully waterproof) |
| Dimensions (approx.) | 15cm (length) x 11cm (diameter) |
| Package Weight | 0.423 kg |
| Package Dimensions | 24cm (L) x 19cm (W) x 12cm (H) |
| Origin | Mainland China |
4. Installation Guide
Follow these steps for proper installation of your motorcycle fog lights:
- For first-time use, remove all protective films from the device and assemble them using the product's built-in accessory kit.
- Connect the wire to a voltage of 12V.
- Connect directly, with the red wire connected to the positive pole and the black wire connected to the negative pole.
- The bracket is directly installed on the collision bar or other suitable installation locations on the motorcycle. The bracket provided with the product is only suitable for collision bars of 18-22mm. The product light is universal and can also be modified and assembled according to the condition of the car.
5. Operation
Once installed and wired correctly, operate the fog lights using your motorcycle's designated switch. Ensure the lights are off when not in use.
6. Maintenance and Storage
- After use, turn off the switch to turn off the lights.
- If not installed and used, please store in a dry place and keep away from children.
- Regularly inspect the lights for any physical damage, loose connections, or signs of wear.
- Clean the lenses with a soft, damp cloth to maintain optimal light output. Avoid abrasive cleaners.
7. Troubleshooting
If you encounter issues with your fog lights, consider the following:
- Lights not turning on:
- Check all wiring connections (red to positive, black to negative) to ensure they are secure and correct.
- Verify that the motorcycle's 12V power supply is active.
- Inspect for any damaged wires or components. Do not use damaged products.
- Dim or flickering lights:
- Ensure connections are clean and free of corrosion.
- Check the bulb (if replaceable) for proper seating or damage. Some users replace with LEDs for brighter output.
- Bracket issues:
- Ensure the bracket is securely fastened to a suitable collision bar (18-22mm diameter).
- Verify that the lights are firmly fixed and not contacting high-temperature parts of the motorcycle.
8. User Tips
- The product features a solid construction with good thickness metal fastenings, ensuring durability.
- Installation is generally straightforward and easy.
- While the body is plastic, it maintains a nice aesthetic.
- Consider replacing the standard bulbs with LED bulbs for enhanced brightness and efficiency, if desired.
9. Frequently Asked Questions (FAQ)
No specific FAQ content was provided for this product. For general inquiries, please refer to the support section.
10. Warranty and Support
This product complies with the latest EU safety and quality regulations for motorcycle lighting accessories. The manufacturer retains complete technical files of conformity.
For further assistance or inquiries, please refer to the official product documentation or contact the seller directly.
A user manual in PDF format is available for download: View User Manual (PDF)