1. Product Introduction
This manual provides essential information for the installation, operation, and maintenance of your AEN DRL LED Boards. These modules are designed to upgrade or replace the Daytime Running Lights (DRLs) in compatible Mercedes-Benz vehicles, enhancing visibility and vehicle aesthetics.
Product Components and Attributes:
| Component | Attributes |
|---|---|
| DRL LED Board / Module | Made of high-brightness LED, aluminum substrate, and high-temperature resistant base. Features low power consumption, high efficiency, and durability. Stably drives daytime running lights, improving safety and visibility. Ideal for headlight maintenance and modification. (Refer to installation diagram for positions: No. 2 is the turn signal module, No. 3 is the DRL module). |
| Headlight Control Module | Made of flame-retardant engineering plastic housing and high-quality electronic components. Features stable performance, anti-interference, and high-temperature resistance. Controls switching and mode changing of automotive headlights, turn signals, and daytime running lights. (Refer to installation diagram for position: No. 1 is the control module). |
| DRL Light Guide Strip | Made of high-transmittance PC material, with uniform and soft light, high-temperature resistance, and anti-aging properties. Guides the LED light source to form an even light band, improving vehicle recognition and appearance. (Refer to installation diagram for position: No. 4 is the light guide strip). |
| LED Light | High-brightness LED chips, aluminum substrate, and high-temperature resistant materials. Features high brightness, low power consumption, and excellent heat dissipation. Used for vehicle daytime running lighting, improving driving safety and appearance recognition. Simple installation and non-destructive replacement. |
| Sensor | Made of ABS engineering plastics and precision electronic components. It is waterproof, dustproof, and shockproof. Used to detect the distance of obstacles behind the vehicle in real-time, assist reversing, and improve driving safety. |
2. Setup and Installation
2.1. Compatibility
These DRL LED Boards are compatible with specific Mercedes-Benz headlight models and years. Please verify your vehicle's headlight type against the list below:

Image Description: Compatibility chart showing four types of Mercedes-Benz headlights: W217 Coupe LED (2015-2020), W205 Low (2015-2018), GLA Xenon (2014-2016), and W205 High (2015-2018).
- 2015-2020 W217 Coupe LED
- 2015-2018 W205 Low
- 2014-2016 GLA Xenon
- 2015-2018 W205 High
2.2. Pre-installation Checklist
- Ensure you have all components: DRL LED Boards, Headlight Control Module, etc.
- Gather necessary tools (not included): screwdrivers, trim removal tools, thermal glue.
- Read all safety instructions before proceeding.
2.3. Installation Procedure
Installation requires careful handling of vehicle components. If you are unsure about any step, it is recommended to seek professional assistance.
- Disconnect Power: Before starting, always disconnect the vehicle's power supply (e.g., battery terminal) to avoid short circuits or electric shock.
- Access Headlight Assembly: Carefully remove any trim or components necessary to access the headlight assembly.
- Disassemble Headlight (if required): Depending on your vehicle model, you may need to partially disassemble the headlight unit to access the DRL modules.
- Locate Components: Refer to the general installation diagram below to identify where each component (Control Module, Turn Signal Board, DRL Board, Light Guide Strip) is typically located within the headlight.
- Install DRL LED Boards: Carefully remove the old DRL boards (if replacing) and install the new AEN DRL LED Boards.
- Apply Thermal Glue: As indicated in the diagram, installation of the DRL module requires thermal glue for secure mounting and heat dissipation. Apply thermal glue as necessary.

Image Description: Diagram illustrating the placement of the DRL LED module within a headlight assembly, with an arrow pointing to the module and text indicating 'Instation require thermal glue!'.
- Connect Wiring: Connect all wiring according to the vehicle's original setup. Ensure all connections are secure.
- Reassemble Headlight: Carefully reassemble the headlight unit and any removed vehicle trim.
- Reconnect Power: Reconnect the vehicle's power supply.
- Test Functionality: Turn on the vehicle and test the DRLs, turn signals, and headlights to ensure all functions are operating correctly.
2.4. General Installation Diagram Overview
Note: Car light models and accessories are for display only; actual installation shall be subject to the real car lights.
- Headlight Control Module: Manages the various lighting functions.
- Turn Signal Light Board/Module: Controls the vehicle's turn signals.
- DRL Board / Module: The main LED board for the Daytime Running Lights.
- DRL Light Guide Strip: The component that diffuses the LED light into an even strip.
2.5. Safety Instructions
Please read and adhere to these safety instructions to prevent injury or damage to the product and vehicle.
- Always disconnect the vehicle power supply before installation to avoid short circuit or electric shock.
- Do not install, disassemble, or repair the product during vehicle operation to prevent safety hazards.
- The product shall be installed in accordance with the installation diagram. Do not modify or forcibly assemble it at will.
- Keep the product away from open fire, high temperature, and water immersion to avoid damage or failure.
- Please use the product under normal vehicle voltage. Do not connect it to non-standard power supply.
- If any damage or abnormal operation is found, stop using it immediately and replace it with a new one.
- Keep the product out of reach of children to avoid accidental injury.
3. Operating Instructions
The AEN DRL LED Boards are designed to function as direct replacements or upgrades for your vehicle's existing Daytime Running Lights. Once correctly installed, they will operate automatically in conjunction with your vehicle's electrical system.
- Automatic Operation: DRLs typically illuminate automatically when the vehicle's engine is running and the headlights are off or in auto mode during daylight hours.
- Color Variants: If you have installed a single-color variant (e.g., White, Blue, Red), the DRLs will display that specific color.
- RGB Variants: For RGB (Multi-color) DRL LED Boards, color changing functionality usually requires an external controller (not always included or detailed in this manual) or specific wiring configurations. Please refer to any additional documentation provided with your RGB variant for instructions on how to change colors. Without a specific controller, RGB modules may default to a specific color or cycle.

Image Description: Front view of a white Mercedes-Benz car with bright blue daytime running lights illuminated.
4. Maintenance
These DRL LED Boards are designed for durability and require minimal maintenance.
- Cleaning: Periodically clean the headlight lens with a soft, damp cloth to ensure maximum light output. Avoid using abrasive cleaners or harsh chemicals that could damage the lens or LED components.
- Inspection: Occasionally inspect the DRLs for any signs of damage or loose connections.
- Avoid Water Immersion: While the components are designed to be water-resistant, avoid direct high-pressure water jets or prolonged immersion, which could compromise seals.
5. Troubleshooting
If you encounter issues with your DRL LED Boards, please refer to the following troubleshooting steps:
- DRLs Not Illuminating:
- Check all electrical connections to ensure they are secure and properly seated.
- Verify that the vehicle's power supply is correctly reconnected and functioning.
- Ensure the vehicle's voltage is within the normal operating range.
- Inspect the DRL LED Boards and wiring for any visible damage.
- DRLs Flickering or Dim:
- Check for loose or corroded electrical connections.
- Ensure a stable power supply from the vehicle.
- Verify that the correct voltage is being supplied to the modules.
- Incorrect Color (RGB Models):
- If using an external controller, ensure it is properly connected and functioning.
- Check the controller's settings or remote control for proper color selection.
- Verify that the RGB module is receiving the correct signals.
- One Side Not Working:
- Swap the DRL LED Board from the working side to the non-working side (if possible and safe) to determine if the issue is with the board or the vehicle's wiring/power.
- Check the specific wiring and connections for the non-working side.
If troubleshooting steps do not resolve the issue, discontinue use and contact your retailer for further assistance.
6. Specifications
| Feature | Detail |
|---|---|
| Brand Name | AEN |
| Model Name | W205 DRL Boards |
| Item Type | Angel Eyes |
| OEM NO. | A2059060601, 1305715284 |
| Origin | Mainland China |
| Material (DRL LED Board) | High-brightness LED, aluminum substrate, high-temperature resistant base |
| Material (Control Module) | Flame-retardant engineering plastic housing, high-quality electronic components |
| Material (Light Guide Strip) | High-transmittance PC material |
| Features | Low power consumption, high efficiency, durability, stable performance, anti-interference, high temperature resistance, uniform and soft light, waterproof, dustproof, shockproof |
| Package Length | 5 cm |
| Package Width | 6 cm |
| Package Height | 7 cm |
| Package Weight | 0.3 kg |
7. User Tips
- Many users find the installation process straightforward, but always take your time and follow the instructions carefully.
- For RGB models, ensure you understand the color control mechanism (e.g., external controller, specific wiring) as it may not be included or detailed in standard packages.
- Always double-check compatibility with your specific Mercedes headlight model and year before purchasing and attempting installation.
- Using thermal glue as instructed is crucial for both secure mounting and proper heat dissipation, which extends the lifespan of the LED boards.
8. Frequently Asked Questions (FAQ)
Q: How do you change the colors on RGB models?
A: For RGB models, color changing typically requires a dedicated controller or specific wiring configuration. Please refer to any additional documentation provided with RGB variants or consult a professional for advanced setups. If no controller is provided, the module might cycle colors or default to a specific one.
Q: How can this be installed?
A: Installation involves disconnecting the vehicle's power, carefully removing existing components, and integrating the new DRL LED boards and modules as per the installation diagram. Thermal glue is required for secure mounting. It is recommended to consult the detailed