1. Important Safety Information
This manual is intended for professional bicycle mechanics. Users without professional training should consult a local bicycle dealer for installation. Always read all instruction manuals included with the product.
- Do not disassemble or modify the product beyond what is stated in this manual.
- Always wear safety glasses or goggles when performing maintenance.
- Use only genuine Shimano parts for replacements.
- Keep this manual in a safe place for future reference.
Safety Warnings:
- DANGER: Failure to follow instructions may result in death or serious injury.
- WARNING: Failure to follow instructions could result in death or serious injury.
- CAUTION: Failure to follow instructions could cause personal injury or physical damage.
2. Product Overview
The Shimano SL-TX50 Tourney SIS TX50 is a thumb shifter designed for mountain bikes, offering reliable gear changes for 3, 6, and 7-speed systems.

Figure 1: Shimano SL-TX50 Tourney Shift Lever components

Figure 2: SL-TX50 Shift Lever pair with included cables

Figure 3: Close-up of 6-speed right shifter and underside detail
3. Setup and Installation
3.1. Tools Required
- Phillips screwdriver #2
- 5 mm Allen key (or 9 mm spanner for some products)
3.2. Mounting the Shifting Lever
- Install the brake lever in a position that does not obstruct brake operation. Ensure there is no interference between the shifter and brake lever throughout the full range of shifter movement.
- Position the shifter on the handlebar.
- Tighten the clamp band using a Phillips screwdriver #2. The recommended tightening torque is 2.5 N-m {22 in. lbs.}.
- Note: Do not open the clamp of the lever excessively during installation, as this may damage the cover.
3.3. Adjustment of the Rear Shifting Lever
Follow these steps in sequence for proper adjustment.
3.3.1. Top Adjustment
- Turn the top adjustment screw (marked 'H') so that the guide pulley is positioned directly over the outer line of the smallest sprocket when viewed from behind.
- Install the chain after this adjustment.
3.3.2. Connection and Securing of Cable
- Inserting the Inner Cable: Insert the inner cable into the outer casing from the end with the marking. Apply grease to the marked end of the casing to maintain operating efficiency.
- Cutting the Outer Casing: When cutting, cut the opposite end to the marked end. After cutting, make the end round and ensure the inside of the hole has a uniform diameter. Attach the appropriate outer end cap to the cut end.
- Connect the cable to the rear derailleur. Ensure the cable is securely seated in its groove. Tighten the cable fixing bolt to 5.0 - 7.0 N-m {44 - 61 in. lbs.}.
3.3.3. Adjustment of Cable Tension
After taking up any initial slack in the cable, re-secure it to the rear derailleur.
3.3.4. Low Adjustment
- While turning the front chainwheel, operate the lever to shift to the lowest gear (largest sprocket).
- Turn the low adjustment screw (marked 'L') so that the guide pulley moves to a position directly below the largest sprocket.
3.3.5. B-Tension Adjustment Screw (for RD-TX75/RD-TX55/RD-TX35)
- Mount the chain on the smallest chainring and the largest sprocket, and turn the crank arm backward.
- Turn the B-tension adjustment screw to adjust the guide pulley as close to the sprocket as possible without touching it.
- Set the chain to the smallest sprocket and repeat the above to confirm correct chain tension.
3.3.6. B-Tension Adjustment Screw (for RD-TZ50)
- Set the chain onto the smallest chainring and the largest sprocket.
- Turn the B-tension adjustment screw to adjust the distance between the tip of the freewheel and the tip of the guide pulley to approximately 10 mm.
- Set the chain to the smallest sprocket and repeat the above to confirm correct chain tension.
3.4. Adjustment of the Front Shifting Lever
Follow these steps in sequence for proper adjustment.
3.4.1. Low Adjustment
For models with a Pro-Set alignment block, remove it first. Set the clearance between the chain guide inner plate and the chain to 0 - 0.5 mm.
3.4.2. Connection and Securing of Cable
Follow the same inner cable insertion and outer casing cutting procedures as for the rear derailleur (Section 3.3.2).
While firmly pulling the inner cable, connect it to the front derailleur. Use a 5 mm Allen key (or 9 mm spanner) to tighten the wire fixing bolt to 5.0 - 7.0 N-m {44 - 61 in. lbs.}.
3.4.3. Adjustment of Cable Tension
After taking up any initial slack in the cable, re-secure it to the front derailleur. Cut off excess inner cable and install an inner end cap.
3.4.4. Top Adjustment
Set the clearance between the chain guide outer plate and the chain to 0 - 0.5 mm.
3.4.5. Adjustment of the Middle Chainring
This adjustment is not necessary for LN (friction type) shifters. Set the clearance between the chain guide inner plate and the chain to 0 - 0.5 mm. Adjust the lever after operating it from top to middle, not low to middle.
4. Operating Instructions
4.1. General Shifting
- Always keep turning the crank during shifting lever operation to ensure smooth gear changes.
- The SL-TX50 features an Optical Gear Display for easy visual confirmation of the selected gear.
4.2. SIS Adjustment (Shimano Index System)
- Operate the shifting lever once to move the chain from the smallest sprocket to the 2nd sprocket.
- While pressing the lever just enough to take up the play, turn the crank arm. The best setting is when the chain touches the 3rd sprocket (counting from the smallest) and makes noise.
- If shifting to the 3rd sprocket: Tighten the outer casing adjustment barrel until the chain returns to the 2nd sprocket.
- If no sound is heard: Loosen the outer casing adjustment barrel until the chain touches the 3rd sprocket and makes noise.
- Return the lever to its original position (2nd sprocket setting) and turn the crank arm clockwise. If the chain still touches the 3rd sprocket and makes noise, turn the outer casing adjustment barrel clockwise slightly until the noise stops.
- Operate the lever through all gears to ensure no noise occurs in any position.
5. Maintenance
5.1. Replacing the Inner Cable
Press the button to set the chain to the first position (top for rear, low for front), then pass the inner cable through the shifter body.
5.2. Cleaning and Lubrication
- Periodically wash chainrings and the chain with a neutral detergent.
- Lubricating the chain after cleaning extends its useful life.
- For optimal SIS performance, periodically lubricate all power-transmission parts.
- For maximum performance, Shimano lubricants and maintenance products are highly recommended.
6. Troubleshooting
After adjustment, check shifting performance. If shifting becomes difficult, refer to the chart below. Adjust bolts by 1/8 turn for each adjustment.
| Problem | Solution |
|---|---|
| Chain falls to the crank side | Turn the top adjustment screw clockwise. |
| Difficult shifting from intermediate to largest chainring | Tighten the cable. If no improvement, turn top adjustment screw counterclockwise. |
| Difficult shifting from largest to intermediate chainring | Loosen the cable. |
| Chain falls to the bottom bracket side | Turn the low adjustment screw clockwise. |
| Intermediate chainring skipped when shifting from largest chainring | Tighten the cable. |
| Difficult shifting from intermediate to smallest chainring | Turn the low adjustment screw counterclockwise. |
7. Specifications
| Feature | Specification |
|---|---|
| Brand | SHIMANO |
| Model | SL-TX50 |
| Series | TOURNEY |
| Part Type | Left/Right Shifter |
| Compatible Bike Type | Mountain Bike (MTB) |
| Clamp Band | Yes |
| Speed Options | 3-speed (Left), 6-speed (Right), 7-speed (Right) |
| Total Gears (Paired) | 18-speed (3x6), 21-speed (3x7) |
| Recommended Outer Casing | OT-SIS40 |
| Shifter Type | Thumb Shifter Plus |
| Material | Alloy |
| Weight | 220g |
| Origin | China |
| Handlebar Caliber | 22.2mm |
| Clamp Band Tightening Torque | 2.5 N-m {22 in. lbs.} |
| Cable Fixing Bolt Torque | 5.0 - 7.0 N-m {44 - 61 in. lbs.} |
8. User Tips
- The SL-TX50 shifters are versatile and can be installed on various bicycle types, including children's bikes and mini-folding bikes, provided the handlebar diameter is compatible.
- Many users find these thumb shifters to be a reliable and effective replacement for original equipment, often preferring them over under-bar levers for ease of use.
- Proper installation and adjustment are straightforward, leading to perfect functionality.
9. Warranty and Support
For the most current warranty information, detailed dealer's manuals, and instruction manuals, please visit the official Shimano website:
Contact Information:
- SHIMANO AMERICAN CORPORATION: One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
- SHIMANO EUROPE B.V.: Industrieweg 24, 8071 CT Nunspeet, The Netherlands. Phone: +31-341-272222
- SHIMANO INC.: 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Please note: Specifications are subject to change for improvement without notice.