SWEVY SW911/SW912

Contents

SWEVY Digital Wood Moisture Meter User Manual

Models: SW911 / SW912

Brand: SWEVY

1. Introduction

This instrument is designed for measuring the moisture content of various materials, including wood, bamboo, paper, cardboard, and Chinese herbal medicines. It determines the percentage of moisture weight relative to the material's dry weight. Please read this manual carefully before using the instrument to ensure proper operation and accurate measurements.

For a visual overview of the product and its features, please watch the video below:

Video: Demonstration of the SWEVY Digital Wood Moisture Meter's features and usage.

2. Features

  • Four tree species options available for varied material measurement.
  • Maximum measurement mode to capture peak moisture values.
  • Temperature compensation function for improved accuracy.
  • Measured value lock (HOLD function) to retain readings.
  • Buzzer notification function (Model SW911 only).
  • Automatic shutdown function to conserve battery life.
  • Large, backlit LCD display for clear readings in various lighting conditions.
  • High-sensitivity bimetallic probes for effective penetration and durability.

3. Product Overview

Familiarize yourself with the components of your moisture meter:

Diagram of SWEVY SW-911 moisture meter with labeled parts and dimensions.

Figure 1: SWEVY SW-911 Moisture Meter Components and Dimensions.

  1. Probe protection cover
  2. Probe
  3. LCD screen
  4. TYPE key (for switching tree species and temperature units)
  5. Backlight/Power button
  6. HOLD/MAX button (for locking values and maximum measurement mode)
  7. Battery compartment

The device dimensions are approximately 135mm (5.315in) x 57mm (2.244in) x 30mm (1.181in).

4. Setup

4.1 Battery Installation

The device requires 3 x 1.5V AAA alkaline batteries or 1.2V AAA rechargeable batteries (batteries not included).

  1. Locate the battery compartment on the back of the device.
  2. Open the battery cover.
  3. Insert the batteries according to the positive (+) and negative (-) indications inside the compartment.
  4. Close the battery cover securely.
  5. If the instrument will not be used for an extended period, remove the batteries to prevent leakage and damage.

5. Operating Instructions

5.1 Power On/Off

  • Power On: Short press the Power button (Power button icon) to turn on the device.
  • Power Off: Long press the Power button to shut down. The instrument will also automatically shut down after 5 minutes of inactivity to save power.

5.2 Backlight Control

  • In the power-on state, short press the Backlight button (Backlight button icon) to turn the LCD backlight on or off. When the backlight is active, a lightbulb icon will be displayed on the screen.
Large backlit LCD display of the moisture meter showing 8.0% moisture.

Figure 2: Large Screen LCD Display with Backlight.

5.3 Measurement Steps

  1. Prepare the material: Ensure the wood or material to be tested is ready.
  2. Prepare the meter: Open the probe protection cover.
  3. Power on: Press the power button to turn on the instrument.
  4. Select Tree Species (TYPE): Short press the TYPE button to cycle through the four available tree species gears (TYPE 1-4). Refer to the 'Tree Species Comparison Table' in the Specifications section to select the appropriate gear for your material.
  5. Insert Probes: Insert both probes into the material along the vertical direction of the horizontal grain. The probe insertion depth should be at least 3mm. Ensure both probes are fully inserted and in full contact with the material for accurate measurement.
  6. Read Measurement: The moisture content will be displayed on the LCD screen.
Close-up of the high-sensitivity probes of the moisture meter.

Figure 3: High-sensitivity probes for accurate penetration.

5.4 Switching Environmental Temperature Units (SW912 only)

  • In the power-on state, long press the TYPE button to switch the display unit of ambient temperature between °C (Celsius) and °F (Fahrenheit).

5.5 Measured Value Lock (HOLD)

  • In the power-on state, short press the HOLD/MAX button to activate the data hold function. The measured value on the screen will be locked, and the "HOLD" icon will be displayed.
  • Short press the HOLD/MAX button again to cancel the value lock.

5.6 Maximum Measurement Mode

  • In the power-on state, long press the HOLD/MAX button to enter the maximum value measurement mode. The "MAX" icon will be displayed. The instrument will continuously measure, and the displayed maximum value will update based on real-time measurements.
  • Long press the HOLD/MAX button again to exit the maximum value measurement mode.
Moisture meter displaying 8.7% in Maximum Measurement Mode.

Figure 4: Maximum Measurement Mode display.

5.7 Buzzer Notification (SW911 only)

  • In the power-on state, press the HOLD button and TYPE button simultaneously to enable or disable the buzzer function. When enabled, a buzzer icon will be displayed on the screen.

6. Maintenance

  • Storage: When storing the instrument, protect it from dust and moisture. Keep the instrument dry and clean to ensure the accuracy of measurement data.
  • Temperature Equalization: If the instrument's body temperature differs significantly from the measured object or ambient temperature, allow the instrument to equalize to the same temperature before use.
  • Probe Care: The instrument is equipped with sharp probes. Handle with care to prevent injury. Keep the probe protection cover on when not in use.
  • Cleaning: Use a soft, dry cloth to clean the instrument. Do not use abrasive cleaners or solvents.

7. Troubleshooting

  • Low Battery Indication: If the battery symbol (Battery icon) is displayed on the screen, the battery is low. Replace the batteries promptly to avoid affecting the instrument's normal operation and measurement accuracy.
  • Inaccurate Readings: Ensure probes are fully inserted and in good contact with the material. Verify the correct tree species type is selected. Allow the instrument to equalize to ambient temperature if there's a significant temperature difference.
  • No Display/Power: Check battery installation and ensure batteries are not depleted.

8. Specifications

SWEVY SW-911 Standard configuration image with product functions and specifications listed.

Figure 5: SWEVY SW-911 Key Functions and Specifications.

Measurement Parameters SW-912 SW-911
Moisture content Measuring Range 2~75% 2~75%
Environment temperature Measuring Range -10~50°C N/A
Environment humidity Measuring Range 0~100%RH (Not condensing) N/A
Moisture content Accuracy ±1.5% ±1.5%
Environment temperature Accuracy ±0.3°C N/A
Environment humidity Accuracy ±3%RH (10~90%RH, 25°C), ±4%RH (Other Range) N/A
Moisture content Resolution 0.1% 0.1%
Environment temperature Resolution 0.1°C N/A
Environment humidity Resolution 0.1%RH N/A
Response Time 1s 1s
Buzzer Notification Yes No
Automatic Shut-down 5 minutes 5 minutes
Operating Temperature -10~50°C -10~50°C
Storage Temperature -20~60°C (Without batteries) -20~60°C (Without batteries)
Power Supply 3 pcs 1.5V AAA alkaline batteries/1.2V AAA rechargeable batteries 3 pcs 1.5V AAA alkaline batteries/1.2V AAA rechargeable batteries
Size of probe Φ2*10mm Φ2*10mm
Size of Device 135*57*30mm 135*57*30mm
Material ABS ABS
Weight About 93g (without batteries) About 93g (without batteries)

8.1 Tree Species Comparison Table

The instrument offers four different gears (TYPE 1-4) to accommodate various tree species and materials. Select the appropriate gear for accurate measurements:

Image showing four tree species options with their corresponding moisture ranges.

Figure 6: Tree Species Options and Measurement Ranges.

Species Gear (TYPE) Species Gear (TYPE)
Rhodesian Teak1Balsa wood3
White red bean tree1Sandalwood3
Brazilian walnut tree1Elm3
Walnut2Koombar3
Clone2Tsuga3
Poplar2Dipterocarp3
Teak2Oak3
Chinese fir3Mason pine4
Douglas fir3Chilean Pine4
Lauan3White Pine4
Fraxinus mandshurica3Larch4
White fir3Apitong4
Maple3Birch4
Ash wood3Linden4

The different gears of the instrument and their measuring ranges are as follows:

  • TYPE1: 2%~40%
  • TYPE2: 2%~50%
  • TYPE3: 2%~60%
  • TYPE4: 2%~75%

9. User Tips

  • Always ensure the probes are clean and free from debris for accurate readings.
  • When measuring, try to insert the probes into multiple spots on the material to get a more representative average moisture content.
  • For very hard woods, apply steady pressure to ensure the probes penetrate sufficiently without bending or breaking.
  • Utilize the 'HOLD' function when taking measurements in hard-to-reach areas to easily record the reading.
  • The 'Maximum Measurement Mode' is useful for quickly identifying the highest moisture spot in a larger area.

10. Warranty and Support

This product is manufactured by Guangzhou SUWEI Electronic Technology Co., LTD, operating under the brand Suwei Technology SWEVY.

For technical support or inquiries, please contact:

  • Address: Room 1314, Building H6, Luogang Aoyuan Square, No.1936, Kaichuang Avenue, Huangpu District, Guangzhou
  • Contact Number: 020-38104332

For further details, you may refer to the official user manual PDF: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.