ZEFIORA V10

Contents

ZEFIORA V10 Electric Bicycle User Manual

Model: V10 Snow Electric Bicycle

Important Safety Information

WARNING: Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.

⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

ZEFIORA V10 Electric Bicycle
The ZEFIORA V10 Snow Electric Bicycle.

Key Safety Practices:

  1. Always Wear A Helmet: Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements in your community. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and eye protection. Also check your state laws concerning other protective gear that may be required when riding the E-bike.
  2. Know Your E-bike: Your new E-bike incorporates many features and functions that have never been built into a bicycle before. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
  3. Ride Within Your Limits: Take it slow until you are familiar with the riding conditions that you encounter. Be especially careful in wet conditions as traction can be greatly reduced and brakes becoming less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue and inattention can significantly reduce your ability to make good judgement and safely.
  4. Keep Your E-bike In Safe Condition: For your safety and enjoyment, and to insure a long life for your E-bike. Inspect and maintain your E-bike regularly. Follow the inspection and maintenance guidelines beginning on page 3. Check critical safety equipment before each and every ride.

Setup and Assembly

The following assembly steps are a general guide. We recommend consulting a certified, reputable bike mechanic to assist with assembly, repair, and maintenance.

Step 1: Unpack and Inventory

Carefully unpack the e-bike from the carton and set out all contents. Remove packaging material protecting the bike frame and components. Please recycle packaging materials (cardboard and #6 EPS foam).

Ensure all pieces are included in the package:

  • V10 E-bike
  • Manual(s)
  • Assembly Tool kit
  • Front fender
  • Front Wheel
  • Handlebar
  • Handlebar holder
  • Charger
  • Pedals (marked left and right)
  • Battery Keys (two, identical with number)

(Diagrams showing the unpacked bike frame, accessories, and tooling kit are typically included in the physical manual.)

Step 2: Initial Frame Preparation

  1. Check the outer carton for completeness and unpack it.
  2. Take out the bicycle frame.
  3. Take out the accessories and tooling kit.
  4. Use an M5 Allen wrench to unscrew the screw on the frame.
  5. Unscrew the screw and remove the trim cover.
  6. Pull out a fixed shelf.

(Diagrams illustrating these steps, such as unscrewing a component and removing a shelf, are typically found in the physical manual.)

Step 3: Handlebar and Front Wheel Installation

  1. Put the steering in front.
  2. Install the retainer and top cover, then tighten all screws.
  3. Loosen the screws and remove the lid.
  4. Install the front and tighten all the screws.
  5. Take out the wheels and accessories.
  6. Install the wheels, paying attention to the order of the accessories.

(Diagrams showing the handlebar assembly, front wheel installation, and accessory order are typically included in the physical manual.)

Step 4: Fender, Pedal, and Dashboard Installation

  1. Tighten the screws on both sides (referring to brake components).
  2. Install the fender and tighten all the screws.
  3. Identify 'R' for Right Pedal and 'L' for Left Pedal, then install them.
  4. Install the pedal and tighten the screw.
  5. Fill the tires with air.
  6. Install the dashboard and tighten all screws.

(Diagrams illustrating the tightening of screws, fender installation, pedal orientation, tire inflation, and dashboard mounting are typically found in the physical manual.)

Step 5: Final Connections and Power On

  1. Connect the ports of cables according to the direction of the arrow.
  2. Press the power button for approximately 3 seconds to turn it on.

Note: It is suggested to check other screws in the frame. If they are loose, you need to tighten them with tools.

(Diagrams showing cable connections and the power button location are typically included in the physical manual.)

Operation

Parts Identification

The ZEFIORA V10 electric bicycle features various components essential for its operation. Familiarize yourself with these parts:

  • Handlebar: For steering and control.
  • Light: Front and rear illumination.
  • Controller: Manages the e-bike's electrical system.
  • Rear Fender: Protects from splashes.
  • Bike Motor: Provides electric assistance.
  • Derailleur: For shifting gears.
  • Tire: 20x4.0 inch fat tires for various terrains.
  • Chain: Connects pedals to the rear wheel.
  • Crank: Connects pedals to the chainring.
  • Pedals: For manual propulsion.
  • Battery: 48V 18AH Lithium Battery, powers the motor and electronics.
  • Front Fork: Suspension component.
  • Disc Brake Rotor: Part of the braking system.
  • LED Headlight: Front illumination.
  • Front Fender: Protects from splashes.
  • Power Button: To turn the e-bike on/off.
  • Speed Mode: Controls the level of electric assistance.
  • Gear Adjustment: For mechanical gear changes.

(A detailed diagram illustrating the location of each identified part on the bicycle is typically provided in the physical manual.)

Display Screen Recognition

The e-bike's display screen provides crucial information during your ride. Here's how to interpret the icons:

Icon Explanation
Headlamps Current state, long press to turn headlights off, long press again to turn headlights on.
Battery The battery has a total of ten cells. When the battery decays to one cell and flashes, it runs out of battery and needs to be charged.
Error The error icon lights up when there are errors in the vehicle and does not light up when there are no errors.
Speed Real-time display of current speed.
Walk When this icon lights up, it indicates that it is currently in pedestrian cart mode and the maximum speed does not exceed 6km/h.
Cruise control When this icon lights up, it indicates that the vehicle is currently in cruise mode.
Gear position On the current interface, press the '+' key to increase the gear position, and press the '-' key to decrease the gear position.
Odometer Total mileage. Press the 'M' button to switch between single mileage, voltage, and current.

(A visual representation of the display screen with these icons is typically provided in the physical manual.)

Gears Operation

Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.

Avoid shifting while standing up on the pedals or under load.

To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring that the chain is fully engaged in that gear before applying more pressure to the pedals. For bicycles with 3 front chain rings, avoid "Cross Chaining." This occurs when the chain is in the smallest cog in the rear combined with the inner or smallest chain ring in the front, or the largest cog in the rear and the outer or largest chain ring in the front. These gear positions put the chain at the most extreme angle and can cause premature wear to the drivetrain. Bicycles with 3 front chain rings have enough gear "overlaps" that these gears are not needed.

(A diagram illustrating correct and incorrect chain positions for gear shifting, particularly highlighting 'Cross Chaining' to avoid, is typically included in the physical manual.)

Charging Procedure

Always charge your battery in temperatures between 50°F - 77°F (10°C - 25°C) and ensure the battery and charger are not damaged before initiating charge. If you notice anything unusual while charging, discontinue charging and use of the bike, then contact for help. Charging the battery fully normally takes 3-7 hours. In rare cases, it may take longer to allow the battery management system to balance the battery, particularly when the bike is new or after long periods of storage.

The battery can be recharged on or off the bike.

  1. Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
  2. With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger (round barrel connector) to the charging port on the side of the battery.
  3. Plug the charger into the outlet, then the charging port. Connect the charger input plug (100-240-volt plug) to the power outlet. Charging should initiate and will be indicated by the LED charge status light on the charger turning red.
  4. Unplug the charger from the outlet, then the charging port. Once fully charged (indicated by the charging indicator light turning green), unplug the charger from the wall outlet first and proceed to remove the charger.

(Images showing the battery charging port and the charger connected to the battery are typically provided in the physical manual.)

Attention: Before charging, make sure that the charger light faces upwards. Full charge normally takes 3-7 hours. Charge the battery in a clean and safe place and do not overcharge.

A red light on the charger means the battery is charging.

A green light on the charger means the battery is fully charged.

Do not charge the battery for more than 12 hours at a time or leave a charging battery unattended.

Ensure the lights face upwards when using the charger. The charge indicator lights on the charger will stay red while the battery charges and one will turn green when charge is complete.

Always charge in dry, indoor locations away from direct sunlight, dirt, or debris. Charge in a clear area away from potential to trip on the charging cords or for damage to occur to the bike, battery, or charging equipment while parked and/or charging. Do not use with the charger inverted, which can inhibit cooling and reduce charger lifespan.

The battery should be recharged after each use, so it is ready to go the full range per charge next ride. There is no memory effect, so charging the battery after short rides will not cause damage.

Ensure the battery is turned off whenever it is being removed or off the bike. Avoid damaging the exposed connector terminals and keep them clear of debris.

Do not touch the "+" and terminal contacts on the bottom of the battery when the battery is removed from the bike.

Maintenance

Pre-Riding Safety Checklist

Before every ride, and after every 25-45 miles, follow this pre-riding safety checklist:

Safety Check Basic Steps
1. Brakes
  • Ensure front and rear brakes work properly.
  • Check brake pads for wear and ensure they are not over-worn.
  • Ensure brake pads are correctly positioned in relation to the rims.
  • Ensure brake control cables are lubricated, correctly adjusted, and display no obvious wear.
  • Ensure brake control levers are lubricated and tightly secured to the handlebars.
  • Test brake levers are firm and that brake, motor cutoff functions, and brake light are functioning properly.
2. Wheels and Tires
  • Ensure tires are inflated to within the recommended limits displayed on the tire sidewalls and holding air.
  • Ensure tires have good tread, no bulges or excessive wear, and are free from any other damage.
  • Ensure rims run true and have no obvious wobbles, dents, or kinks.
  • Ensure all wheel spokes are tight and not broken.
  • Check axle nuts and front wheel quick release skewer is correctly tensioned, fully closed, and in a secure position.
3. Steering
  • Ensure handlebar and stem are correctly adjusted and tightened and allow proper steering.
  • Ensure the handlebar is set correctly in relation to the forks and the direction of travel.
4. Chain
  • Ensure the chain is oiled, clean, and runs smoothly.
  • Extra care is required in wet, salty/otherwise corrosive, or dusty conditions.
5. Bearings
  • Ensure all bearings are lubricated, run freely, and display no excess movement, grinding, or rattling.
  • Check headset, wheel bearings, pedal bearings, and bottom bracket bearings.
6. Cranks and Pedals
  • Ensure pedals are securely tightened to the cranks.
  • Ensure the cranks are securely tightened and are not bent.
7. Derailleurs
  • Check that the derailleur is adjusted and functioning properly.
  • Ensure shifter and brake levers are attached to the handlebar securely.
  • Ensure all brake and shift cables are properly lubricated.
8. Frame, Fork, and Seat
  • Check that the frame and fork are not bent or broken. If either is bent or broken, they should be replaced.
  • Check that the seat is adjusted properly and the seat post quick release lever is securely tightened.
9. Motor Drive Assembly
  • Ensure the hub motor is spinning smoothly and motor bearings are in good working order.
  • Ensure all power cables running to the hub motor are secured and undamaged.
  • Make sure the hub motor axle bolts are secured and all torque arms and torque washers are in place.
10. Battery
  • Ensure the battery is charged before use.
  • Ensure there is no damage to the battery.
  • Lock the battery to the frame and check to see that it is secured.
  • Charge and store the bike and battery in a dry location, between 50°F-77°F.
  • Let the bike dry completely before using again.
11. Electrical Cables
  • Look over connectors to make sure they are fully seated, free from debris or moisture.
  • Check cables and cable housing for obvious signs of damage.
  • Ensure headlight, taillight, and brake light are functioning, adjusted properly, and unobstructed.
12. Accessories
  • Ensure all reflectors are properly fitted and not obscured.
  • Ensure all other fittings on the bike are properly secured and functioning.
  • Inspect helmet and other safety gear for signs of damage.
  • Ensure the rider is wearing a helmet and other required riding safety gear.
  • Ensure mounting hardware is properly secured if fitted with a rear rack.
  • Ensure taillight and taillight power wire are properly secured if fitted with a rear rack.
  • Ensure fender mounting hardware is properly secured if fitted with fenders.
  • Ensure there are no cracks or holes in fenders if fitted with fenders.

Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 miles (80-160km), and bolted connections can loosen. Always have a certified, reputable mechanic perform on your E-bike after your initial break-in period of 50-100 miles (80-160km) (depending on riding conditions such as total weight, riding characteristics, and terrain). Regular inspections and tune-ups are particularly important for ensuring that your bike remains safe and fun to ride.

Basic Bike Care

To ensure safe riding conditions, you must properly maintain your e-bike. Follow these basic guidelines:

  1. Properly maintain batteries by keeping them fully charged, especially if stored for up to two weeks. Refer to the Long-Term Battery Storage section of the manual for longer storage periods.
  2. Never immerse or submerge the bike or any components in water or liquid, as the electrical system may be damaged.
  3. Periodically check wiring and connectors to ensure there is no damage and that connections are secure.
  4. To clean, wipe the frame with a damp cloth. If needed, apply a mild non-corrosive detergent mixture to the damp cloth and wipe the frame. Dry by wiping with a clean, dry cloth.
  5. Store under shelter; avoid leaving the bike in the rain or exposed to corrosive materials. If exposed to rain, dry your bike afterwards and apply anti-rust treatment to the chain and other unpainted steel surfaces.
  6. Riding on the beach or in coastal areas exposes your bike to salt, which is very corrosive. Wipe down your bike frequently and wipe or spray all unpainted parts with anti-rust treatment. Damage from corrosion is not covered under warranty, so special care should be given to extend the life of your bike when used in coastal areas or areas with salty air or water.
  7. If the hub and bottom bracket bearings have been submerged in water or liquid, they should be taken out and re-greased. This will prevent accelerated bearing deterioration.
  8. If the paint has become scratched or chipped in the metal, use touch-up paint to prevent rust. Clear nail polish can also be used as a preventative measure.
  9. Regularly clean and lubricate all moving parts, tighten components, and adjust as required.

Troubleshooting

This section provides solutions to common issues you might encounter with your ZEFIORA V10 electric bicycle.

Symptoms Possible Causes Most Common Solutions
It doesn't work
  • Insufficient battery power
  • Faulty connections
  • Battery not fully seated in tray
  • Improper turn on sequence
  • Brakes are applied
  • Charge the battery
  • Clean and repair connectors
  • Install battery correctly
  • Turn on bike with proper sequence
  • Disengage brakes
Irregular acceleration and/or reduced top speed
  • Insufficient battery power
  • Loose or damaged throttle
  • Charge or replace battery
  • Replace throttle
When powered on the motor does not respond
  • Loose wiring
  • Loose or damaged throttle
  • Loose or damaged motor plug wire
  • Damaged motor
  • Repair and/or reconnect
  • Tighten or replace
  • Secure or replace
  • Repair or replace
Reduced range
  • Low tire pressure
  • Low or faulty battery
  • Driving with too many hills, headwind, braking, and/or excessive load
  • Battery discharged for long period of time without regular charges (aged or damaged)
  • Brakes rubbing
  • Adjust tire pressure
  • Check connections or charge battery
  • Assist with pedals or adjust route
  • Replace the battery
  • Adjust the brakes
The battery won't charge
  • Charger not well connected
  • Charger damaged
  • Battery damaged
  • Wiring damaged
  • Adjust the connections
  • Repair or replace
Wheel or motor makes strange noises
  • Damaged motor bearings
  • Damaged wheel spokes or rim
  • Damaged motor wiring
  • Replace
  • Repair or replace
  • Repair or replace motor
Sensor Issue
  • Sensor loose
  • Sensor or cable broken/damaged
  • Adjust the connections
  • Repair or Replace
Pre-load and turn off bike suddenly
  • Battery or motor overheat protection
  • Battery or controller cable loose
  • Battery or controller cable damaged
  • Wait 1-3 minutes to restart e-bike
  • Adjust the connections
  • Repair or Replace

Specifications

The ZEFIORA V10 electric bicycle is designed with the following specifications:

Item Name Product Specification
Model Number V10
Brand Name ZEFIORA
Vehicle Size 164*68*115 (CM)
Packing Size 136*27*85 (CM)
Color Black
Frame Material Steel, Aluminum alloy
Net Weight 38kg (83.77lb)
Gross Weight 46kg (101.41lb)
Max. Support Weight 150kg (264.55lb)
Max Speed <25km/h (50KM/H listed in table, but <25km/h in properties)
Inner Tire Pressure 20PSI / 140KPA
Charger AC-DC 54.6V 2A 100-240V AC DC5.5X2.1
Battery 48V 18AH Lithium Battery
Brake System Front and rear disc brake
Tire Size 20x4.0 inch
Pedal Aluminum alloy pedal
Wattage > 500w (800w mentioned in title)
Range per Power 10 - 30 km
Motor Brushless
Folded No
Rated Passenger Capacity One Seat
High-concerned chemical None

User Tips

Based on general electric bicycle usage and common practices, here are some tips for an optimal experience:

  • Regular Tire Pressure Checks: Maintaining the correct tire pressure (20 PSI / 140 KPA) is crucial for ride comfort, efficiency, and preventing punctures. Check before each ride.
  • Smooth Shifting: When changing gears, ease off the pedals slightly to reduce tension on the chain and derailleur. This prolongs the life of your drivetrain components.
  • Battery Care: Always store your battery in a cool, dry place and avoid extreme temperatures. Charge it regularly, even if not used frequently, to maintain battery health.
  • Pre-Ride Inspection: A quick check of brakes, tire pressure, and secure connections before each ride can prevent many common issues and ensure safety.
  • Visibility: Always use the LED headlight and ensure reflectors are clean and visible, especially when riding in low light conditions. Consider wearing bright clothing.

(Note: Specific user tips from buyer reviews were not available for this manual.)

Warranty and Support

For detailed warranty information, please refer to the official documentation provided with your purchase. In case of issues not covered by this manual's troubleshooting section, please contact your seller or an authorized service center.

A comprehensive user manual in PDF format is available for download and reference. You can typically find this document on the product's support page or by contacting the seller directly. The PDF manual contains additional diagrams and detailed instructions.

Reference to the official user manual (PDF): ZEFIORA V10 Electric Bicycle User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.