Xiaomi Mijia CW300 Outdoor Camera User Manual

1. Important Safety Precautions

Please read this manual carefully before use and retain it for future reference. Failure to follow these instructions may result in damage to the product or personal injury.

• Operating Temperature: The camera is designed to operate within a temperature range of -30°C to 60°C. Do not use the camera in environments outside this specified range.
• Water and Dust Resistance: This camera has an IP66 dust-tight and water-resistant rating. While robust, avoid using it in extremely humid environments or locations where water ingress is possible to ensure normal operation.
• Power Adapter: The included power adapter is NOT waterproof and is for indoor use ONLY. Do not expose the power adapter to humid conditions. The power adapter's operating temperature range is -30°C to 45°C.
• Lens Placement: For optimal image quality, do not place the camera with its lens facing or next to reflective surfaces (e.g., glass windows, white walls). This can cause overexposure in close areas and underexposure further away, or produce washed-out images.
• Wi-Fi Signal: Ensure the camera is installed in an area with a strong Wi-Fi signal. Avoid installing it near microwave ovens or other devices that may interfere with Wi-Fi signals.
• Night Vision: A slight clicking sound may be heard when enabling or disabling night vision; this is normal and indicates the infrared cut-off filter is switching.
• Power Cable: If the power cable becomes damaged, contact the after-sales service team for replacement. Do not attempt to repair it yourself.
• Product Information: The product's nameplate information, including model and serial numbers, is located on the bottom of the device.

2. Product Overview

2.1. Package Contents (Figure A)

Figure A: Contents of the Xiaomi Mijia CW300 Outdoor Camera package.

1. Xiaomi Outdoor Camera CW300
2. Wall Mount
3. Mounting Template Sticker
4. Power Adapter
5. Waterproof Network Port Accessories
6. Waterproof Tape
7. Mounting Screws
8. User Manual
9. Warranty Notice
10. Attention Sticker

2.2. Camera Components (Figure B)

Figure B: Front and side view of the camera highlighting its main parts.

1. Power Port
2. Network Cable Port
3. Indicator Light
4. Microphone
5. Lens
6. Spotlight
7. Waterproof Cover
8. Reset Button
9. MicroSD Card Slot

Note: Illustrations in this manual are for reference only. Actual product appearance and functions may vary due to product enhancements.

3. Setup Guide

3.1. Installing a MicroSD Card (Figure C-1)

The camera supports local storage via a MicroSD card. Ensure the camera is unplugged before proceeding.

1. Remove the waterproof cover from the MicroSD card slot.
2. Insert a MicroSD card with its contact side facing up into the slot.
3. Replace the waterproof cover securely to prevent water ingress.

Figure C-1: Steps for inserting a MicroSD card into the camera.

CAUTION:

• Always unplug the camera when inserting or removing the MicroSD card.
• Use a qualified brand MicroSD card. The camera supports a maximum capacity of 256 GB and FAT32 format only.
• MicroSD cards with 64 GB or above may need to be formatted to FAT32 via the Mi Home/Xiaomi Home app (Settings > Manage storage).
• A MicroSD card with a read/write speed of no less than U1/Class 10 is recommended.

3.2. Powering On (Figure C-2)

1. Plug the power adapter cable into the power port on the camera.
2. The camera will automatically turn on.
3. Once the indicator light remains orange and a voice notification is heard, the camera is successfully powered on.

IMPORTANT:

• Use only the original power adapter cable provided.
• Do not manually turn or force the camera lens to rotate when it is powered on. If the lens positioning is inaccurate, calibrate it within the Mi Home/Xiaomi Home app.

3.3. Indicator Light Status

• Orange: Awaiting connection / Reset successful
• Blinking Orange: Connecting to a network...
• Blinking Blue: Connecting to a server / OTA update in progress...
• Blue: Connected successfully / Working normally

3.4. Connecting to the Mi Home/Xiaomi Home App

The Xiaomi Mijia CW300 camera operates with the Mi Home/Xiaomi Home app, allowing you to control your device and integrate it with other smart home devices.

1. Scan the QR code provided in the manual or search for "Mi Home/Xiaomi Home" in your device's app store (Google Play Store or Apple App Store) to download and install the app.
2. Open the Mi Home/Xiaomi Home app.
3. Tap the "+" icon in the upper right corner to add a new device.
4. Follow the on-screen instructions within the app to complete the device pairing process.

Note:

• Ensure your network connection is stable and the camera is powered on with the indicator light remaining orange during the connection process.
• Once connected, the indicator light will turn blue.
• If you need to change the network or the Xiaomi account connected to the camera, press and hold the reset button (located near the MicroSD slot) for approximately 7 seconds until a voice notification confirms the reset. Resetting the camera will not delete data on the MicroSD card.

3.5. Camera Installation (Figures D & E)

Proper installation is crucial for the camera's performance and durability. The camera can be wall-mounted or ceiling-mounted.

Figure D: Steps for mounting the camera. Figure E: Assembly of waterproof network port accessories.

3.5.1. Mounting Steps

1. Positioning (Figure D-1): Stick the mounting template sticker on the desired wall location. Ensure the right side of the sticker is at least 50 cm away from any wall corner.
2. Drilling (Figure D-1): Drill holes in the wall that align with the sticker's markings. The holes should be approximately 6 mm in diameter and 35 mm deep.
3. Wall Plugs (Figure D-2): Insert the plastic wall plugs into the drilled holes.
4. Wall-Mounted Installation (Figure D-3): Attach the wall mount to the wall by inserting screws through the mount and into the wall plugs. If the power cable is routed upwards, feed it through the groove in the wall mount first before securing the mount.
5. Ceiling Installation (Figure D-4): Rotate the camera's base upwards, align it with the clip on the mounting bracket, and tighten the screw on the right side to secure it.
6. Waterproofing Power Port (Figure D-5): Once the camera is securely mounted, wrap the waterproof tape around the power port connection to prevent water ingress.

3.5.2. Installation Cautions

• The mounting surface must be capable of supporting at least three times the total weight of the camera.
• To prevent potential injury, ensure the camera is securely fixed to the wall according to these instructions.
• Do not install the camera near heat sources such as outdoor air conditioning units, range hood outlets, or gas water heater outlets.

3.5.3. Installing Waterproof Network Port Accessories (Figure E)

These accessories enhance the network port's waterproof performance. They include a sealing ring, waterproof sleeve, stopper, and waterproof rear cover.

1. Sealing Ring (Figure E-1): Place the sealing ring onto the camera's network port.
2. Cable Assembly (Figure E-2): Thread the waterproof rear cover, stopper, and waterproof sleeve over the network cable in that order.
3. Connection: Plug the network cable into the camera's port.
4. Secure Assembly (Figure E-3): Screw the waterproof sleeve and sealing ring together. Then, screw the waterproof rear cover and waterproof sleeve together.

Note: Even if a network cable is not used, install these waterproof accessories to protect the port. Use a shielded network cable for best performance.

4. Operating the Camera

Once the camera is set up and connected to the Mi Home/Xiaomi Home app, you can access its features:

• Live View: Access real-time video feed from your smartphone.
• Recording: View recorded footage stored on the MicroSD card or cloud storage (if subscribed).
• Motion Detection & Alerts: Configure motion detection zones and sensitivity, and receive notifications on your phone. The camera features AI humanoid monitoring.
• Two-Way Audio: Use the built-in microphone and speaker to communicate through the camera.
• Night Vision: The camera automatically switches to night vision in low-light conditions, providing clear images.
• Settings: Adjust various camera settings such as image quality (2.5K ultra-clear), Wi-Fi settings, storage management, and privacy settings (e.g., customizable sleep time).

The camera provides 2.5K ultra-clear image quality for detailed monitoring.

Supports both wired and 2.4GHz Wi-Fi connections for stable networking.

Built-in Mijia security chip ensures data privacy with AES128-bit encryption.

5. Maintenance

• Cleaning: Gently wipe the camera lens and body with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
• Waterproof Seals: Periodically inspect all waterproof covers and seals (MicroSD slot, power port, network port) to ensure they are intact and properly closed.
• Firmware Updates: Regularly check for and install firmware updates via the Mi Home/Xiaomi Home app to ensure optimal performance and security.

6. Troubleshooting

7. Specifications

The IP66 rating ensures reliable operation in various weather conditions.

8. User Tips

• Region Compatibility: Be aware that some users have reported region-specific limitations. This camera might be intended for use in mainland China and may not be fully compatible or mix well with Xiaomi products from other regions (e.g., Korean versions). Verify regional compatibility if you plan to integrate it with an existing smart home ecosystem from a different region.
• MicroSD Card for Recording: The camera supports MicroSD cards for local video recording. Ensure you have one installed if you wish to store footage directly on the device.
• Packaging: The product is typically well-packaged to ensure safe delivery.

9. Warranty and Support

9.1. WEEE Information

All products bearing this symbol (crossed-out wheeled bin) are Waste Electrical and Electronic Equipment (WEEE) as per Directive 2012/19/EU. They should not be mixed with unsorted household waste. Please dispose of this product at a designated collection point for the recycling of WEEE to protect human health and the environment.

9.2. EU Declaration of Conformity

Hereby, Shanghai Moshon Technology Co., Ltd. declares that the radio equipment type Xiaomi Outdoor Camera CW300 (Model MBC41) is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.mi.com/global/service/support/declaration.html

Under normal use, this equipment should be kept at a separation distance of at least 20 cm between the antenna and the user's body.

CAUTION: Possibly hazardous optical radiation emitted from this product. Do not stare at the operating lamp. May be harmful to the eyes.

9.3. Manufacturer Information

Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Shanghai Moshon Technology Co., Ltd. (a Mi Ecosystem company)
Address: No. 668 Shenzhuan Road, Songjiang Hi-Tech Park, Caohejing Development Zone, Shanghai, China

9.4. Further Support

For detailed warranty information, technical support, or service inquiries, please refer to the official Xiaomi website or contact their customer service in your region. A comprehensive user manual is also available in PDF format at: Xiaomi Outdoor Camera CW300 User Manual (PDF).