Voktta 62-5912

Contents

DC UPS 5V 9V 12V Uninterrupted Power Supply

6x18650 DIY Power Bank Box for Routers, Optical Cats, and Cellphones

Product Overview

This device is a versatile DC Uninterrupted Power Supply (UPS) designed to provide backup power for various low-voltage electronics such as optical modems, routers, surveillance cameras, and cellphones. It functions as a DIY power bank box, utilizing six 18650 lithium-ion batteries (not included) and offering multiple output voltages (5V, 9V, 12V).

Key features include welding-free battery installation, automatic charge and discharge management, and stable performance with a peak output power of up to 60W.

Product overview video demonstrating the DC UPS unit.

Safety Precautions

  • Battery Polarity: Always ensure correct battery polarity. Install the spring to the negative pole and the copper sheet to the positive pole. Installing batteries in reverse will cause damage to the unit.
  • Battery Type: Use only 3.7V cylindrical flat-head 18650 batteries. Pointed batteries longer than 2MM cannot be used.
  • Battery Quality & Pairing: For optimal performance and safety, use high-quality batteries of the same brand, model, capacity, and batch. Ensure they have consistent voltage.
  • Input Voltage: The input voltage for charging must be within the 12-13V range. Exceeding 13V may damage the charging circuit. Voltages below 12.7V may not fully charge the battery. A range of 12.7-13V is recommended.
Diagram showing correct and incorrect battery installation polarity

Diagram illustrating correct battery installation (spring to negative, copper to positive) versus incorrect (reverse) installation, which can cause damage.

Setup Instructions

1. Battery Installation

  1. Open the battery compartment cover.
  2. Insert six 3.7V cylindrical flat-head 18650 batteries into the battery slots. Ensure the spring contacts the negative terminal and the copper plate contacts the positive terminal of each battery.
  3. Ensure the batteries, frame, and circuit board fit closely together.
  4. Close the battery compartment cover.
Open DC UPS unit with battery slots and DC cable

Image showing the DC UPS unit with its cover removed, revealing the six 18650 battery slots and the internal circuit board.

Internal view of battery slots with springs and copper contacts

Close-up of the battery slots, highlighting the spring (negative) and copper plate (positive) contacts for correct battery insertion.

Diagram of battery frame and installed batteries

Diagram showing the battery frame with six 18650 batteries installed, ready to be inserted into the case.

2. Activating Output

After installing the batteries, locate the power switch (SW) and move it to the "ON" position. Then, press the activation switch on the circuit board to enable output.

Circuit board with activation switch highlighted

Image of the circuit board, with the activation switch clearly marked for enabling power output after battery installation.

Operating Instructions

Charging the UPS

Connect a 12-13V adapter to the "INPUT 12-13V" port on the device. The "CHR" indicator light will glow red during charging and turn off when fully charged. For optimal UPS functionality, ensure the input adapter power meets or exceeds the total load power plus 6W for battery charging.

The product features an internal charging current limiting circuit.

Output Ports and Usage

The device provides multiple output voltages for various applications:

  • USB 5V (USB5V2A): Can be connected to 5V routers, surveillance cameras, or used for charging cellphones.
  • 9V (9V1A): Can be connected to 9V routers or cameras.
  • 12V (12V3A): Can be connected to 12V optical cats or surveillance devices.

The input and output ports function similarly, both supporting input/output and featuring UPS functionality. The product does not stabilize voltage; the battery is directly connected in series for output, and the voltage increases or decreases with the amount of electricity.

Close-up of DC UPS ports with labels for 5V, 9V, 12V outputs and charging input

Close-up view of the DC UPS ports, indicating the USB 5V, 9V, and 12V output ports, and the 12-13V charging input.

Diagram showing typical wiring for 5V, 9V, and 12V devices

Typical wiring diagram demonstrating how to connect various devices (5V router, 9V router, 12V optical cat) to the DC UPS outputs.

Maintenance

Battery Replacement

The welding-free design allows users to freely disassemble and replace batteries. To remove the battery compartment, use your thumbnails to jam into the two tabs (Bayonet A and B) and gently tip the frame out in the direction of the green arrows using your ring fingers.

Diagram showing how to remove the battery compartment using tabs

Diagram illustrating the process of removing the battery compartment by disengaging tabs A and B.

DC UPS unit with batteries, highlighting welding-free design

Image showing the internal battery arrangement, emphasizing the welding-free design for easy battery replacement.

General Care

Keep the device clean and free from dust. Avoid exposing it to extreme temperatures or moisture. When not in use for extended periods, store it with partially charged batteries.

Troubleshooting

  • No Output After Battery Installation:
    • Ensure batteries are installed with correct polarity (spring to negative, copper to positive).
    • Verify the power switch is in the "ON" position.
    • Press the activation switch on the circuit board.
  • Batteries Not Fully Charging / Undercharging:
    • Check that the input adapter voltage is within the recommended 12.7-13V range. Voltages below 12.7V may result in incomplete charging.
    • Ensure the input adapter power is sufficient (>= total load power + 6W battery charging power).
  • Device Overheating:
    • Immediately disconnect the power source and remove batteries.
    • Check for reverse battery installation, which can cause severe overheating and damage.
    • Ensure high-quality, properly paired batteries are used.
  • Inconsistent Performance / Short Battery Life:
    • This device does not include a battery balancing function. Ensure all six 18650 batteries have very similar parameters (brand, model, capacity, internal resistance) for optimal performance and longevity. Mismatched batteries can lead to unbalanced discharge and reduced overall capacity.

Specifications

Feature Specification
Model 62-5912
Battery Type 3.7V cylindrical flat-head 18650 lithium-ion batteries (6 required, not included)
Battery Capacity (Calculated) 6 * 3.7V * 3400mAh = 74 Wh (based on 3400mAh cells)
Rated Output Power 12V5A = 60W (Max)
Output Voltages Independent output 12V (3-5A), 9V (1A), USB 5V (2-3A)
Charging Input 12-13V DC (recommended 12.7-13V)
Overcharge Protection 4.25V * 3
Low Voltage Protection 2.75V * 3
Overcurrent Detection Voltage 0.1V ± 0.025V
Temperature Range -20°C to 60°C
DC Interface Standard DC 5.5 * 2.1mm (positive inside, negative outside)
Dimensions (L x W x H) Approx. 125mm x 93mm x 25mm (4.92in x 3.66in x 0.98in)
Voltage (Adapter Input) 220V (This refers to the AC input for the charging adapter, not the device output)
Origin Mainland China
Dimensions of the DC UPS unit

Image showing the length and width dimensions of the DC UPS unit.

DC UPS unit with batteries and DC cable

The DC UPS unit with batteries installed and the included DC cable.

User Tips

  • Battery Matching: Since the unit does not have a balancing function, it is crucial to use 18650 batteries that are closely matched in terms of capacity, internal resistance, and voltage. This will ensure balanced discharge and prolong the life of your battery pack.
  • Charging Voltage: For optimal charging and to prevent undercharging, ensure your external power adapter provides at least 12.6V, ideally within the 12.7-13V range.
  • Versatile Use: This UPS is highly effective for maintaining power to essential devices like Wi-Fi routers and optical modems during power outages, ensuring continuous internet access.
  • Easy Assembly: The welding-free design makes assembly and battery replacement straightforward, even for DIY beginners.

Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller directly through the platform where the product was purchased. Keep your purchase records handy for faster service.

A user manual in PDF format is available for download: Download User Manual (PDF)

© 2024 Voktta. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.