Antec A-12015

Contents

Antec A-12015 High Performance Chassis Fan User Manual

Model: A-12015 | Brand: Antec

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of your Antec A-12015 High Performance Chassis Fan. Designed for optimal cooling in PC gaming rigs, this fan features a 9-leaf copper core blade, PWM smart temperature control, and a high-speed silent motor. Please read this manual thoroughly before use to ensure proper function and longevity of your product.

2. Safety & Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.

3. Package Contents

The Antec A-12015 fan package typically includes:

  • Antec A-12015 Chassis Fan (quantity may vary based on purchase)
  • Mounting Screws
  • User Manual (this document)
Antec A-12015 fans and mounting screws next to the product box.
Image: Contents of the Antec A-12015 package, including fans and mounting screws.

4. Specifications

The Antec A-12015 fan is engineered for high performance and quiet operation. Key specifications are detailed below:

AttributeValue
Model NumberA-12015
Fan DimensionsL120mm x W120mm x H15mm
Fan Size120mm
Fan Speed800 - 1800 RPM ±10%
Noise Level18.3 - 37.2 dBA
Air Flow23.46 - 61.51 CFM
Air Pressure0.29 - 1.71 mm/H₂O (MAX)
Fan Connector4-PIN PWM
Rated Voltage12V
Fan Life (MTTF)≥40000 hours (Room Temp: 25°C)
Bearing TypeCopper core hydraulic bearing (Fluid Bearing)
Blade Quantity9
Used ForCase, Radiator
Supported PlatformsIntel: LGA1700/1200/115X/1356/1366
AMD: AM5/AM4/AM3/AM2/FM2/FM1
Xeon: E5/X79/X99/2011/2066

*Official Data For Reference Only

Table of Antec A-12015 fan specifications including dimensions, speed, noise, airflow, pressure, connector, voltage, MTTF, bearing type, and supported platforms.
Image: Detailed product parameters for the Antec A-12015 fan.
Diagram showing the dimensions of the Antec A-12015 fan: 120mm x 120mm x 15mm.
Image: Fan dimensions (120mm x 120mm x 15mm).

5. Setup and Installation

Follow these steps to properly install your Antec A-12015 chassis fan:

  1. Preparation: Ensure your computer is powered off and unplugged from the wall outlet. Open your computer case to access the fan mounting locations.
  2. Mounting Location: Identify a suitable 120mm fan mounting spot in your PC case or on your radiator. Consider airflow direction for optimal cooling (intake or exhaust).
  3. Secure the Fan: Position the fan in the desired location. Use the provided mounting screws to secure the fan to the case or radiator. Do not overtighten the screws.
  4. Connect Power: Locate a 4-pin PWM fan header on your motherboard. Connect the fan's 4-pin connector to this header. The 55cm long cable provides flexibility for routing.
    Close-up of the 4-PIN PWM fan connector and cable.
    Image: The 4-PIN PWM fan connector.
  5. Cable Management: Route the fan cable neatly to avoid interference with other components and to improve airflow within the case.
  6. Close Case: Once the fan is securely installed and connected, close your computer case and reconnect the power.
Diagram illustrating airflow direction of a fan installed in a computer case, showing air being pulled in and pushed out.
Image: Example of fan airflow direction when installed in a chassis.

6. Operating Instructions

The Antec A-12015 fan utilizes PWM (Pulse Width Modulation) technology for smart temperature control, allowing your motherboard to automatically adjust fan speed based on system temperature.

  • Automatic Speed Control: When connected to a 4-pin PWM header on your motherboard, the fan speed will automatically adjust between 800-1800 RPM based on the CPU or system temperature, as configured in your motherboard's BIOS/UEFI settings or through system monitoring software.
  • Manual Speed Control: You can typically override automatic control and set custom fan curves or fixed speeds through your motherboard's BIOS/UEFI settings or dedicated software provided by your motherboard manufacturer.
  • Silent Operation: The fan's fluid bearing and noise-reducing blade design ensure quiet operation, especially at lower RPMs, maintaining a noise level between 18.3-37.2 dBA.

7. Maintenance

Regular maintenance helps ensure optimal performance and extends the lifespan of your fan:

  • Cleaning: Periodically clean the fan blades and housing to remove dust buildup. Use compressed air or a soft brush. Ensure the fan is powered off and unplugged before cleaning.
  • Inspection: Check for any obstructions around the fan blades or unusual noises during operation.
  • Cable Check: Ensure the 4-pin PWM cable remains securely connected to the motherboard.

8. Troubleshooting

If you encounter issues with your Antec A-12015 fan, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Fan not spinning
  • Loose or incorrect power connection
  • Faulty fan header on motherboard
  • Fan is defective
  • Check that the 4-pin PWM connector is securely plugged into the motherboard.
  • Try connecting the fan to a different fan header on the motherboard.
  • If still not spinning, the fan may be defective. Contact support.
Excessive noise
  • Dust buildup on blades
  • Loose mounting screws
  • Fan blades hitting cables
  • Bearing issue
  • Clean fan blades with compressed air or a soft brush.
  • Ensure all mounting screws are tightened.
  • Check for any cables obstructing the fan blades and secure them.
  • If noise persists, the bearing may be worn. Consider replacement.
Poor cooling performance
  • Incorrect airflow direction
  • Insufficient fan speed
  • Dust buildup
  • Verify the fan is oriented correctly for intake or exhaust.
  • Adjust fan speed settings in BIOS/UEFI or software to a higher RPM.
  • Clean the fan and surrounding areas for dust.

9. User Tips

  • Optimal Airflow: Plan your case's airflow carefully. Generally, front and bottom fans should be intake, and rear and top fans should be exhaust for best cooling.
  • PWM Control: Utilize your motherboard's PWM control features to create custom fan curves. This allows the fan speed to dynamically adjust, providing quiet operation during light loads and maximum cooling during intense tasks.
  • Regular Cleaning: Dust is the enemy of cooling. Make it a habit to regularly clean your fans and dust filters to maintain optimal performance and extend component life.
  • Check Connections: Always ensure all fan cables are securely connected to the motherboard headers to prevent unexpected shutdowns or performance issues.

10. Manufacturer & Support Information

For further assistance or warranty inquiries, please contact the manufacturer or their authorized representative:

  • Manufacturer: Dongguan Kimdoole Technology Co., Ltd.
  • Address: No. 15, Guangming Road, Guanmei Xiang, Shuanggang Village, Houjie Town, Dongguan City, Guangdong Province, China (Back Row, 3rd Floor)
  • Contact: Jinduo Technology 86-15975539585, 867743438@qq.com
  • EU Authorized Representative: VAT SPEED SL
  • EU Address: Calle Antonio Salvador N99.1, 28026 Madrid, Spain
  • EU Contact: 34-916321624, services@vatspeed-eu.com

For the full user manual in PDF format, please refer to the official documentation provided by the seller.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.