1. Introduction
Thank you for choosing the Tungfull USB Cordless Rotary Tool. This versatile mini electric drill pen combo kit is designed for various DIY tasks such as engraving, polishing, cutting, drilling, and cleaning. Please read this manual thoroughly before operating the tool to ensure safe and efficient use.
Figure 1: Tungfull USB Cordless Rotary Tool (Various Colors)
2. Safety Information and Warnings
Failure to follow these instructions may result in damage to the product or personal injury.
- General Safety: Read all instructions before use. Do not use this product for purposes other than its intended use. Inspect the product before each use; do not use if damaged. Follow installation and operation guidelines to avoid injury.
- Children's Safety: Keep the device and its cord out of reach of children under 3 years old. Keep away from children unless supervised by an adult.
- Ingestion Warning: In case of ingestion, seek medical attention immediately.
- Electrical Safety: Do not expose the tool to water or moisture.
- Handling Sharp/Dangerous Items: Handle with care to avoid cuts or injuries when using accessories.
- Battery Safety: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with applicable legal requirements.
3. Package Contents
Please check the package for the following items:
- 1 x Tungfull Cordless Rotary Tool
- 1 x USB Charging Cable
- Assorted Grinding Heads
- Assorted Drill Bits
- Polishing Wheels
- Cutting Discs
- Sanding Bands
- Wire Brushes
- Collets (various sizes)
- Wrench for chuck
- Other accessories as per kit variant
Figure 2: Complete Kit Contents
4. Setup
4.1 Initial Preparation
- Unpack all components from the box.
- Remove any protective films from the device.
4.2 Charging the Tool
Before first use, fully charge the rotary tool.
- Connect the provided USB cable to the charging port on the tool.
- Connect the other end of the USB cable to a certified 5V power adapter (not included).
- The charging indicator lights will show the charging status. Ensure the tool is fully charged before use for optimal performance.
4.3 Replacing and Installing the Chuck/Collet
The tool uses different collets to accommodate various accessory shank sizes (0.5-3.2mm).
- Unscrew the black chuck nut at the front of the tool.
- Remove the existing collet (if any).
- Insert the appropriate collet for your accessory's shank size into the tool's shaft.
- Insert the accessory (e.g., drill bit, grinding stone) into the collet.
- Screw the black chuck nut back on and tighten it securely using the provided wrench to hold the accessory firmly in place. Do not overtighten.
Figure 3: Chuck and Collet System
5. Operation
5.1 Power On/Off and Speed Regulation
- To Power On: Press and hold the power button (usually located on top of the tool) for approximately 3 seconds until the indicator lights illuminate.
- Speed Adjustment: The tool features a 3-block speed regulation. Short press the power button to cycle through the different speed settings (6000-15000 RPM). The indicator lights will show the current speed level.
- To Power Off: Press and hold the power button again for approximately 3 seconds until the indicator lights turn off.
5.2 Using the Tool for Various Applications
The Tungfull rotary tool is suitable for a wide range of applications. Always select the appropriate accessory and speed for the material and task.
- Polishing: Use polishing wheels or buffs to smooth surfaces or remove rust.
- Carving/Engraving: Attach engraving bits for detailed work on wood, plastic, or soft metals.
- Drilling: Use small drill bits for precision holes in various materials.
- Cutting: Attach cutting discs for light cutting tasks on plastic, thin metal, or wood.
- Cleaning: Use wire brushes or abrasive accessories to clean surfaces.
Video 1: Product Demonstration (Shows speed regulation, chuck replacement, polishing, carving, drilling, and cutting)
Figure 4: Versatile Applications of the Rotary Tool
6. Maintenance
6.1 Cleaning
- After each use, turn off and unplug the tool.
- Use a soft, dry cloth to wipe down the tool's body.
- Remove any dust or debris from the chuck area and ventilation slots using a small brush or compressed air.
- Do not use harsh chemicals or abrasive cleaners.
6.2 Storage
- Store the tool and its accessories in a dry, clean place.
- Keep the tool away from direct sunlight, moisture, and extreme temperatures.
- Ensure the tool is stored out of reach of children.
7. Troubleshooting
- Tool does not turn on: Ensure the battery is fully charged. Check if the power button is pressed and held for the required 3 seconds.
- Tool stops during operation: The battery might be low. Recharge the tool. If the tool overheats, allow it to cool down before resuming use.
- Accessory wobbles or falls out: Ensure the correct collet size is used for the accessory shank. Make sure the chuck nut is tightened securely.
- Reduced performance: The battery may need recharging. Ensure accessories are clean and not worn out.
8. Specifications
| Feature | Specification |
|---|---|
| Product Name | Cordless Drill / Rotary Tool |
| Brand Name | tungfull |
| Model | 8952 |
| Power Source | Battery (3.7V) |
| No-Load Speed | 6000-15000 RPM (3-block regulation) |
| Clamping Range | 0.5 - 3.2 mm |
| Charger Type | USB (requires 5V adapter) |
| Tool Dimensions (L x W) | 150mm x 30mm |
| Origin | Mainland China |
| Certifications | CE, FCC, RoHS |
| Use | Home DIY |
| Battery Included | Yes |
| Package Dimensions (L x W x H) | 20cm x 10cm x 6cm |
| Package Weight | 0.139 kg |
Figure 5: Tool Dimensions and Key Specifications
9. User Tips
- Start Slow: When working on a new material or with a new accessory, always start with the lowest speed setting and gradually increase it as needed.
- Light Pressure: Let the tool do the work. Apply light, consistent pressure rather than forcing the accessory, which can lead to damage or poor results.
- Test on Scrap: Before working on your final piece, test the accessory and speed setting on a scrap piece of the same material.
- Wear Safety Gear: Always wear appropriate safety glasses and gloves to protect yourself from debris.
10. Warranty and Support
For warranty claims or technical support, please contact the manufacturer directly using the information below:
- Manufacturer: ShenZhen Tungfull Digital Technology Co., Ltd
- Address: A302, Building 25, Hong Chao Yuan, ChangFa Mid Road, BanTian Subdistrict, LongGang District, ShenZhen, China
- E-mail/Tel: 56827370@qq.com / +86-15089309815
Please retain your proof of purchase for any warranty-related inquiries.