SHIMANO Tiagra 4700

Contents

SHIMANO Tiagra 4700 2x10s Derailleurs Groupset

User Instruction Manual

Introduction

This manual provides detailed instructions for the installation, adjustment, and maintenance of your SHIMANO Tiagra 4700 2x10s Derailleurs Groupset. Please read this manual thoroughly before use to ensure correct and safe operation. For further detailed diagrams and instructions, please refer to the official Shimano Dealer's Manual (PDF) available at this link.

SHIMANO Tiagra 4700 Groupset components: ST-4700 shifters, FD-4700 front derailleur, and RD-4700-GS rear derailleur.

Figure 1: SHIMANO Tiagra 4700 Groupset components (ST-4700, FD-4700, RD-4700-GS)

Important Safety Information

DANGER: Failure to follow instructions will result in death or serious injury.

WARNING: Failure to follow instructions could result in death or serious injury.

CAUTION: Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.

  • Always follow instructions provided in the manuals when installing components. Use genuine Shimano parts to prevent loosening or damage, which can lead to serious injury.
  • Wear safety glasses or goggles to protect your eyes during maintenance or part replacement.
  • Understand your bicycle's brake system thoroughly. Improper use can lead to loss of control or falls.
  • Applying the front brake too strongly can lock the wheel, causing a fall and serious injury.
  • Always ensure front and rear brakes are working correctly before riding.
  • Braking distance increases in wet weather. Reduce speed and apply brakes early and gently.
  • Wet road surfaces reduce tire grip. Reduce speed and apply brakes early and gently to avoid skidding.
  • Do not alter carbon levers; they may break, leading to brake failure. Inspect carbon levers for damage (peeling, cracking) before each ride. If damaged, stop using the bicycle and consult a dealer.
  • Clean carbon levers with a soft cloth and neutral detergent. Avoid high temperatures and fire.
  • Ensure the crank is turning during gear shifting.
  • Use an outer casing with sufficient length to allow full handlebar turns without tension.
  • Use OT-SP cable and cable guide for smooth operation.
  • Grease inner cables and the inside of outer casings with SIS SP41 grease (Y04180000) for proper sliding. Do not use premium grease or other types for gear shifting cables as it may degrade performance.

Setup and Installation

Tools Required

  • 5 mm Allen key
  • Cable cutter "TL-CT12"
  • 3 mm slotted screwdriver (for ST-9001/ST-9000/ST-6800)
  • 2 mm Allen key (for ST-5800/ST-4700/ST-4703)
  • Shimano E-ring removal tools: Y6RT66000, Y6RT68000
  • Screwdriver #1

Installation to the Handlebar

  1. Turn over the bracket cover from the back side. Gently turn over the ends of the bracket cover with both hands and slowly push them down. Avoid forceful pulling to prevent damage.
  2. Position the shifter on the handlebar.
  3. Use a 5 mm Allen key to tighten the clamp bolt.
Close-up of ST-4700 shifters with cables, ready for installation.

Figure 2: ST-4700 Shifters

Tightening Torque for Clamp Bolt: 6.0 - 8.0 N·m (52 - 70 in. lbs.)

Installation of the Brake Cable

  1. Ensure the inner cable (BC-9000/BC-R680/BC-1051, Ø1.6 mm) does not contact the shifting lever or caliper brake adjustment section to prevent coating damage.
  2. Use an outer casing (Ø5 mm) with sufficient length for full handlebar turns.
  3. Depress the lever as if to brake and thread the brake cable through. Ensure the inner end is firmly set in the cable hook.

Installing the Shifting Cable

  1. Temporarily secure the outer casing to the handlebar with tape.
  2. Use polymer coating inner cable (Ø1.2 mm) and recommended SP41 outer casing (Ø4 mm).
  3. Cut the outer casing using a cable cutter (TL-CT12) on the side opposite the inscription. Expand the tip of the liner (Ø2.2 mm or more) and arrange the cut end into a perfect circle. Insert the outer casing until it touches the seating surface of the outer cap.
  4. Operate lever (B) 10 or more times to set it to the top position.
  5. Remove the cable cover using a slotted screwdriver.
  6. Thread the inner cable through, being careful not to damage the coating. Insert the cable so the inner end attaches to the unit.
  7. Reinstall the cable cover.
  8. Temporarily secure the outer casing to the handlebar.
  9. Wrap the handlebar with handlebar tape.

Adjustment

Lever Stroke Adjustment

Adjust the lever stroke using a 3 mm slotted screwdriver (for ST-9001/ST-9000/ST-6800) or a 2 mm Allen key (for ST-5800/ST-4700/ST-4703).

  • Counterclockwise: The lever stroke becomes larger.
  • Clockwise: The lever stroke becomes smaller.

Ensure braking operates properly after adjustment.

Operating Instructions

The SHIMANO Tiagra 4700 groupset is designed for smooth and reliable 2x10 speed shifting on road bicycles. Your dual control levers (ST-4700) integrate both braking and shifting functions.

  • Shifting Gears: Use the larger lever for upshifts (to a larger gear/smaller cog) and the smaller lever for downshifts (to a smaller gear/larger cog). Ensure you are pedaling while shifting to allow the chain to move smoothly between cogs and chainrings.
  • Braking: Squeeze the main lever body towards the handlebar to engage the brakes. Apply both front and rear brakes simultaneously for effective stopping power. Practice braking to understand the feel and response of your bicycle's brake system.
  • Front Derailleur (FD-4700): Shift the front derailleur using the left-hand lever to move the chain between the two chainrings.
  • Rear Derailleur (RD-4700): Shift the rear derailleur using the right-hand lever to move the chain across the 10-speed cassette.

Maintenance

Bracket and Lever Disassembly

  1. Use Shimano E-ring removal tools (Y6RT66000, Y6RT68000) to remove the E-ring. Wear protective glasses as the E-ring may pop out.
  2. Pull out the lever axle by gently tapping the assembly with an Allen key and plastic hammer. Always remove the lever axle in the specified direction to avoid damaging the bracket body.

Assembling Bracket Body and Lever Body

  1. Insert the lever into the bracket.
  2. Insert the end of the return spring into the notch.
  3. Align stud holes and use Shimano tool (Y6RT66000) to press-fit the lever axle. Ensure the E-ring groove faces up and the bracket body surface is flat.
  4. Remove the tool and use Shimano tool (Y6RT68000) to install a new E-ring. Do not reuse old E-rings.

Replacing the Bracket Cover

  1. Remove the lever from the bicycle.
  2. Match the tabs on the bracket cover to the slots on the bracket.
  3. Wipe a little rubbing alcohol inside the bracket cover to ease installation.
  4. Note: Bracket covers for ST-9001 and ST-9000 are not interchangeable. Check R (right) or L (left) markings.

Replacing the Nameplate

  1. Shift the larger shift lever until both screws are accessible.
  2. Remove the screws with a screwdriver (#1) and replace the nameplate.

Tightening Torque for Nameplate Screws: 0.15 - 0.20 N·m (1.3 - 1.7 in. lbs.)

Replacing the Main Lever Support

  1. Operate lever (B) two or more times, then shift lever (A) by two gears.
  2. Hold the base of lever (A) and return only lever (A) to its original position.
  3. Rotate the main lever support with a slotted screwdriver and remove the stopper.
  4. Pull out the old main lever support and insert the new one.

Replacement of the SL Cable Guide

  1. Remove the lever from the handle and then remove the bracket cover.
  2. Remove the cable cover.
  3. Use a pointed tool to pry out the old SL cable guide.
  4. Push in the new cable guide with your hands.
  5. Install the cable cover.

Replacing the Cable Cover

  1. Remove screws at the bottom of the bracket and remove the lower cover (if present).
  2. Remove the cable cover from the bracket using a screwdriver and pull the cable out.
  3. Before installing a new cable cover, make a slight crease on it and insert it into the hole in the bracket.
  4. Install the lower cover to the bracket.

Tightening Torque for Cable Cover Screws: 0.20 - 0.25 N·m (1.7 - 2.2 in. lbs.)

How to Pull Out the Disconnected Inner End (Shifting Cable)

  1. Remove the lever from the handle and then remove the bracket cover.
  2. Remove the screws at the bottom of the bracket and remove the two covers (unit cover and lower cover).
  3. Pull out the inner end on the cable hook of the winding body. Be careful not to touch the spring accidentally.
  4. Reattach the two covers and tighten the screws.

Tightening Torque for Cover Screws: 0.20 - 0.25 N·m (1.7 - 2.2 in. lbs.)

Troubleshooting

  • Shifting Issues: If gear shifting is not smooth or precise, check the following:
    • Ensure inner cables are properly greased and free of dust.
    • Verify outer casing length is correct (not too long or too short).
    • Check if the rear fork ends are aligned.
    • Inspect cables for fraying or damage.
    • Ensure lever stroke is correctly adjusted.
  • Brake Ineffectiveness: If brakes feel spongy or lack power:
    • Check brake cable tension and ensure cables are not stretched or damaged.
    • Inspect brake pads for wear and proper alignment with the rim.
    • Ensure brake levers are properly adjusted for reach.
  • Noise: Unusual noises during shifting or braking can indicate:
    • Misaligned derailleurs.
    • Dry or dirty chain.
    • Worn brake pads or misaligned calipers.

For persistent issues, consult a professional bicycle mechanic or refer to the detailed Shimano Dealer's Manual.

Specifications

FeatureSpecification
BrandSHIMANO
Model Number4700
Derailleur Groupset TypeMechanical Derailleur system
TypeGroupset
MaterialAlloy
Gears10 Speed
Total Capacity (Cassette)11-25T, 12-28T, 11-32T
ComponentsDerailleurs (Shifters, Front Derailleur, Rear Derailleur)
OriginJapan (Jp)

Warranty and Support

For warranty information, please refer to the documentation provided with your purchase or visit the official SHIMANO website. For technical support or service, please contact your authorized SHIMANO dealer or a professional bicycle mechanic.

SHIMANO INC.
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.