SZRZGT 36-54W / 54-72W

Contents

SZRZGT 2.4G LED Driver Instruction Manual

Output 24V 36-54W 72W 2.4G LED Driver AC110V 220V Color Dimming & Changeable Power Supply For Dual Colors LED Strip Chandelier

1. Introduction

This manual provides essential information for the safe and efficient use of your SZRZGT 2.4G LED Driver. This power supply is designed for dual color LED strips and chandeliers, offering color dimming and changeable color temperature functionalities via a 2.4G remote control.

SZRZGT 2.4G LED Driver and Remote Control
SZRZGT 2.4G LED Driver and Remote Control.

2. Safety Warnings

  • Not suitable for children under 3 years old.
  • Do not look directly at the product with your eyes when it is operating.
  • Ensure proper heat dissipation for the product during operation.
  • Always adhere to electronic security protection guidelines during installation and use.
  • Installation should be performed by qualified personnel to prevent electric shock or damage.

3. Package Contents

Your package should contain the following items:

  • 1 x 2.4G 24V LED Driver (either 36-54W or 54-72W model)
  • 1 x 2.4G Remote Control (battery not included)
Comparison of SN-RF54/72CW and SN-RF36-54CW LED Dimming Power Supplies
Comparison of the two available LED Driver models.

4. Specifications

Attribute Value
Brand Name SZRZGT
Item Type Lighting Transformers
Model Number 36-54W / 54-72W (SN-RF36-54CW / SN-RF54-72CW)
Input Voltage AC100-240V
Output Voltage DC24V
Output Current (36-54W model) 2.15A
Output Current (54-72W model) 2.6A
Nominal Voltage 10-50V
Origin Mainland China

Note: If using a 110V input, the output power will be approximately 50% of the rated wattage.

5. Setup

5.1. Wiring the LED Driver

The LED driver is designed for dual color LED strips or chandeliers. Ensure correct polarity when connecting the output to your LED fixture.

SZRZGT 2.4G LED Dimming Power Supply with pre-wired input and output cables
LED Driver with pre-wired input (AC) and output (DC24V) cables.

5.2. Remote Control Pairing

All new remote controls must be paired with the LED driver before first use. Follow these steps:

  1. Connect the LED driver to your lamp fixture.
  2. Turn on the lamp and wait for approximately 5 seconds.
  3. Within the next 3-5 seconds, press the 'ON 1#' button on the remote control for 3-5 seconds, or press it 3-5 times rapidly.
  4. The lamp will flicker on/off three times, indicating successful pairing.
  5. You can now use the remote to control the lamp.
Diagram illustrating remote control pairing instructions for Remote A, Remote B, and Remote C models
Visual guide for remote control pairing process.

6. Operating Instructions

Once paired, use the remote control to manage your LED lighting. The remote typically features buttons for:

  • On/Off: To turn the light on or off.
  • Dimming: Adjust brightness levels (e.g., 'Brightness +' and 'Brightness -').
  • Color Temperature Change: Switch between warm white ('Warm Color') and cool white ('Cold Color') or adjust the color temperature.
  • Preset Modes: Some remotes may have numbered buttons (1, 2, 3, 4) for different lighting scenes or zones.
Close-up view of the 2.4G RF Remote Control for LED Driver, showing buttons for dimming, color change, and presets.
Remote control layout with various functions.

7. Maintenance

7.1. LED Welding Instructions

For any necessary repairs or modifications involving LED welding, observe the following guidelines:

  • Immersion Welding: Control welding temperature at 230°C ± 5°C for a maximum of 5-10 seconds. The immersion welding position should be at least 3 millimeters away from any colloid.
  • Soldering with a Soldering Iron: Use a constant temperature soldering iron for manual soldering. The maximum temperature for a single contact of the solder pad is 350°C for 3-5 seconds. Ensure the soldering iron is grounded, and static electricity does not exceed safe limits. The welding position should be at least 3 millimeters away from any adhesive.

7.2. LED Heat Dissipation Notice

Proper heat management is crucial for the longevity and performance of LED components:

  • It is recommended to use LED heat dissipation aluminum profiles. For integrated LED chips above 20W, consider adding a fan for active heat dissipation. Ensure the temperature of the light bulb does not exceed 50°C.
  • Use heat sinks with a surface area greater than 50 square centimeters for 1W LED beads, and greater than 150 square centimeters for 3W LED beads. The lamp beads must be tightly attached to a flat heat sink.
  • Thermal conductive silicone grease should be used to fill the gap between the bottom of the lamp bead and the heat sink. Apply only a thin layer; excessive grease can hinder heat dispersion.
Diagram showing LED components, power supply, aluminum substrate, and heat sink for proper heat dissipation.
Diagram illustrating LED components and heat dissipation principles.

7.3. Pin Forming Instructions

  • The bracket must be at least 2 millimeters away from the gel before it can be bent.
  • Bracket forming must be done using fixtures and completed by professionals.
  • Ensure bracket forming is completed before welding.
  • The pins and spacing of the formed bracket must be consistent with those on the circuit board.

8. Troubleshooting

8.1. Remote Control Not Responding

  • Check Battery: Ensure the remote control has working batteries. (Note: Battery is not included in the package).
  • Re-pair Remote: If the remote stops responding, try re-pairing it with the LED driver by following the steps in Section 5.2.
  • Obstructions: Ensure there are no obstructions between the remote and the LED driver that might interfere with the 2.4G signal.

8.2. Light Not Turning On

  • Power Connection: Verify that the LED driver is correctly connected to the AC power source (AC100-240V).
  • LED Fixture Connection: Check that the LED strip or chandelier is properly connected to the DC24V output of the driver, observing correct polarity.
  • Driver Failure: If all connections are secure and the remote is paired, the LED driver might be faulty.

9. User Tips

  • If your light fixture stops working, consider checking or replacing the LED driver as a common point of failure. Many users have found success by replacing this component to restore their lighting.
  • For optimal performance and longevity, ensure the LED driver is installed in a well-ventilated area to aid in heat dissipation.

10. Warranty and Support

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

For additional documentation, a user manual PDF may be available. Please refer to the product page or contact support for access to this resource: User manual (PDF)

© 2024 SZRZGT. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.