XINOWY S7

Contents

XINOWY S7 Motorcycle Helmet Bluetooth Headset

User Manual - Model S7

1. Important Safety Warnings

Before using the XINOWY S7 Bluetooth Headset, please read this manual carefully and keep it for future reference. Adhere to all safety instructions to prevent injury or damage.

1.1 FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

1.2 Interference Guidelines

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs with radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

1.3 RF Exposure

The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

2. Product Overview

The XINOWY S7 is a high-performance Bluetooth headset designed for motorcycle helmets, offering advanced features for a safe and enjoyable riding experience.

XINOWY S7 Helmet Bluetooth Headset with key features highlighted

Figure 2.1: S7 Headset with Noise Reduction, 1000mAh Battery, IP67 Waterproof, Auto Answering.

2.1 Key Features

  • Bluetooth 5.4: Ultra-fast connection and immersive sound for a smooth wireless experience.
  • Intelligent Noise Reduction: Dual-core adaptive noise-canceling chip for a quiet riding environment.
  • IP67 Waterproof & Dustproof: Fully sealed design and nano-coating technology ensure protection against rain, wind, and dust.
  • High-Fidelity (HIFI) Sound: Delivers clear audio quality for music and calls.
  • Intelligent Call Control: Supports automatic and manual answering modes.
  • Long Battery Life: Equipped with a 1000mAh battery for extended use.
  • RGB Lighting Effects: Enhances visibility and style.

2.2 Package Contents

The package typically includes:

  • S7 Bluetooth Headset Unit
  • Headphones with Microphone (Soft Mic or Hard Mic, depending on selection)
  • USB Type-C Charging Cable
  • Mounting Clips and Hook-and-Loop Fasteners
  • User Manual (this document)

3. Setup and Installation

Follow these steps to properly install your S7 Bluetooth headset onto your helmet.

3.1 Pre-Installation Check

Before permanent installation, connect the earphones to your mobile phone to test the volume. If the volume is significantly different after installation, adjust the speaker position inside the helmet.

3.2 Installation Steps (Fix by Clips)

  1. Attach Steel Clip: Pull the steel clip slightly wider and insert it directly into the left edge of the helmet.
  2. Prepare Speaker Area: Lift the felt lining corresponding to the hook of the inner cavity speaker at the ear position of the helmet. Attach the provided hook-and-loop fasteners to this area.
  3. Install Left Loudspeaker: Attach the hook side of the loudspeaker (the one with the shorter wire) to the corresponding loop side properly on the left side of the helmet.
  4. Install Right Loudspeaker: Attach the hook side of the loudspeaker (the one with the longer wire) to the corresponding loop side properly on the right side of the helmet.
  5. Position Microphone: Stick the butterfly-shaped sticky board in the appropriate position on the left side of the helmet. Place the microphone so it aligns with your mouth. Ensure all wires are neatly arranged and tucked under the inner lining.
  6. Connect Headphone Plug: Insert the headphone plug into the headset unit's headphone jack.
  7. Installation Complete: Verify all components are securely attached and wires are not interfering with helmet comfort or safety.
Soft Microphone for S7 Headset

Figure 3.1: Example of Soft Microphone setup.

4. Operating Instructions

4.1 Kind Reminders

  • Charge the device immediately when you hear the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.