1. Introduction
Thank you for choosing the GVDA GD170D AC/DC Digital Clamp Meter. This instrument is a high-performance, true RMS digital clamp meter with multiple functions, designed to make your electrical work easier, more efficient, and safer. Please read this manual carefully before using the product and store it properly for future reference.
2. Safety Information
WARNING: Please read this manual carefully before using this product. Failure to follow safety instructions may result in electric shock, personal injury, or damage to the instrument.
- WARNING marks indicate conditions and operations which may cause danger to the user.
- CAUTION marks refer to conditions and operations which may cause damage to the instrument or equipment.
- To avoid possible electric shock or personal injury, please abide by the following specifications:
- Do not use the instrument if it is damaged, or if the instrument shell or plastic parts are cracked.
- Do not use the instrument around explosive steam, gas, or dust.
- When measuring, keep your fingers behind the finger protector of the probe.
- When measuring AC current, clamp the conductor in the center of the pliers.
- Do not measure voltages higher than 750V AC or 1000V DC.
- Before opening the battery cover, remove the test probes from the instrument.
- Replace the battery when the low battery indicator appears.
Safety Symbols:
- ⚠: High voltage warning
- ~: Alternating current (AC)
- ⎓: Direct current (DC)
- ⏚: Ground
- ⧈: Double insulation
- CE: Conforms to European Union directives
- CAT III: Overvoltage Category III
- CAT IV: Overvoltage Category IV
3. Package Contents
Please check the contents of your package. If any items are missing or damaged, contact your retailer.
- 1 x GVDA GD170D AC/DC Digital Clamp Meter
- 1 x Pair of Test Leads (Red and Black)
- 1 x K-Type Thermocouple
- 1 x User Manual
- 1 x Carrying Bag
4. Product Overview
Familiarize yourself with the components of your clamp meter.

Panel Description:
- Clamp Head
- Flashlight
- NCV Sensor
- Function Knob
- Display Screen
- Function Keys (FUNC, INRUSH, VFD, MAX/MIN, REL/ZERO)
- Measuring Input Jacks (VΩHz, COM)
- Trigger (for opening clamp)
- Data Hold Key (on the side of the instrument)
5. Setup
Battery Installation or Replacement:
The meter uses three AAA 1.5V batteries. To install or replace batteries:
- Ensure the instrument is turned OFF and all test leads are disconnected.
- Use a screwdriver to loosen the screw on the battery cover located at the back of the meter.
- Remove the battery cover.
- Insert new AAA batteries, observing the correct polarity (+ and -) as indicated inside the compartment.
- Replace the battery cover and tighten the screw securely.
WARNING: To avoid electric shock, remove the test probes before opening the battery cover.
6. Operating Instructions
General Operation:
- Auto Power Off: The meter will automatically power off after approximately 15 minutes of inactivity to save battery energy. Press any key to power it on again.
- FUNC Key: Used to switch between functions (e.g., AC/DC voltage, resistance/continuity/diode) when multiple functions share the same knob position.
- INRUSH Key: Directly enters the INRUSH current measurement function.
- VFD Key: Enters the Variable Frequency Drive measurement mode for voltage or current.
- MAX/MIN Key: Displays the maximum or minimum measured value.
- REL/ZERO Key: Used for relative value measurement or to zero out DC current readings.
- HOLD Key: (Side button) Freezes the current reading on the display. Press again to release.
Measurement Functions:
- AC/DC Voltage Measurement:

Figure 2: AC Voltage Measurement - Turn the function knob to the V~ (AC Voltage) or V⎓ (DC Voltage) position.
- Connect the red test lead to the VΩHz jack and the black test lead to the COM jack.
- Connect the test probes in parallel to the circuit or component under test.
- Read the voltage value on the display.
- AC/DC Current Measurement:

Figure 3: DC Current Measurement - Turn the function knob to the A~ (AC Current) or A⎓ (DC Current) position.
- Press the trigger to open the clamp jaws and clamp around a single conductor.
- Ensure the clamp jaws are completely closed and the conductor is centered within the jaws for accurate measurement.
- Read the current value on the display. For DC current, use the REL/ZERO button to zero the display before measurement if needed.
- Inrush Current Measurement:

Figure 4: Inrush Current Test - Turn the function knob to the A~ position.
- Press the INRUSH key.
- Clamp around the conductor of the device you want to test the inrush current for (e.g., motor, compressor).
- The meter will capture the peak current during startup. The measurement time is approximately 100ms.
- VFD (Variable Frequency Drive) Measurement:
- Turn the function knob to the A~ or V~ position.
- Press the VFD key. The display will show