1. Introduction
This manual provides comprehensive instructions for setting up, operating, and maintaining your Tuya Smart Temperature and Humidity Sensor with an external probe. This device allows for precise monitoring of environmental conditions and integrates seamlessly with smart home ecosystems like Tuya SmartLife, enabling remote monitoring, data recording, and smart automation.
The sensor is available in two versions: a WiFi version and a Zigbee version. Please ensure you have the correct version for your smart home setup.
2. Important Safety Information
- The external temperature sensor probe is not made of food-grade material. Do not place the probe in food or water intended for human consumption.
- The sensor unit is not waterproof and is designed for indoor use only.
- Only use LR03-1.5V alkaline batteries (AAA size). Do not use rechargeable batteries (1.2V) as they may cause incorrect voltage detection and premature low battery warnings.
- Do not mix batteries of different models, brands, or new and old batteries. Using inferior batteries can lead to configuration failures or rapid battery depletion.
- Ensure the device is placed in an area with good wireless signal strength after configuration to prevent increased power consumption.
3. Package Contents
- Tuya Smart Temperature and Humidity Sensor (T01/ZT01)
- External Temperature Probe (100cm cable length)
- User Manual (PDF version available at PDF User Manual)
Note: AAA batteries are not included and must be purchased separately.
4. Specifications
| Feature | Specification |
|---|---|
| Model Number | T01/ZT01 |
| Product Type | Temperature Humidity Meter |
| Thermometer Use | Refrigerator Thermometers (and general environment) |
| Thermometer Type | Digital |
| Material | Plastic |
| Size | 71mm x 25mm x 20mm (2.79in x 0.98in x 0.78in) |
| Power Supply | LR03-1.5V/AAA*2 (not included) |
| Wireless Protocol | WiFi 2.4GHz (for WiFi version) / Tuya Zigbee (for Zigbee version) |
| Temperature Range (Internal) | -9.9℃ ~ 60℃ |
| Temperature Resolution (Internal) | ±1℃ |
| Humidity Range | 0% ~ 99%RH |
| Humidity Resolution | ±5%RH |
| Probe Temperature Range | -40℃ ~ 120℃ |
| Probe Temperature Resolution | ±1℃ |
| APP Name | Smart Life, Tuya Smart |
| Smart Home Ecosystem Types | Tuya |
| Is Smart Device | Yes |

Visual representation of product dimensions and key specifications.
5. Setup Guide
5.1. Pre-requisites
- A smartphone (Android 6.0+ or iOS 11+) with Bluetooth enabled.
- A 2.4GHz Wi-Fi network (for WiFi version) or a Tuya Zigbee Hub (for Zigbee version). The WiFi version requires a 2.4GHz WiFi network; it does not support 5GHz. The Zigbee version requires a Tuya Zigbee Hub and does not support Zigbee2Mqtt.
- The correct Wi-Fi network name (SSID) and password.
- Two LR03-1.5V/AAA alkaline batteries (not included).

Diagram illustrating the network requirements for WiFi and Zigbee versions.
5.2. Battery Installation
- Gently push the cover of the battery compartment downwards to open it.
- Insert two LR03-1.5V/AAA alkaline batteries, ensuring the positive and negative poles are aligned correctly.
- Close the battery compartment cover.
5.3. App Installation and Account Creation
- Scan the QR code provided in the manual or search for "Smart Life" in the Google Play Store (for Android) or Apple App Store (for iOS) to download and install the app.
- Open the Smart Life app and create a new account using your mobile number and an authentication code.
5.4. Device Pairing
Ensure your mobile phone is connected to the 2.4GHz Wi-Fi network (for WiFi version) or your Zigbee hub is powered on and connected (for Zigbee version).
- Open the Smart Life app.
- On the homepage, tap the "+" icon in the upper right corner, then select "Add Device".
- Select "Temperature and Humidity Sensor (BLE+Wi-Fi)" from the "Sensors" category.
- Bluetooth Mode (Recommended for initial setup): The app will prompt you to turn on Bluetooth on your mobile. It will automatically search for the device. Enter your Wi-Fi name and password (if prompted), and the device should connect automatically.
- Wi-Fi Mode (if Bluetooth fails or for manual selection): Ensure the LED indicator on the sensor is blinking quickly. If not, press and hold the reset button for about 5 seconds until it blinks quickly. Follow the in-app instructions to connect.
- AP Mode (if Wi-Fi Mode fails): If the LED indicator is blinking slowly, select "Blink Slowly" in the app. Press and hold the reset button for about 5 seconds until the LED blinks slowly. Connect your mobile to the device's hotspot (e.g., "SmartLife-XXXX") in your phone's Wi-Fi settings, then return to the app interface to complete the connection.
6. Operating Instructions
6.1. Temperature & Humidity Monitoring
- The sensor detects both environmental temperature and humidity using its built-in sensors.
- View real-time temperature and humidity readings directly in the Smart Life app.
- Access historical data: The app displays statistics for temperature and humidity changes per Day, Month, and Year. You can also export this data to your email address.

App interface for viewing historical data and exporting records via email.
6.2. External Probe Usage
The external probe extends the sensor's capabilities, allowing temperature detection in specific locations:
- Aquariums/Fish Tanks: Monitor water temperature.
- Refrigerators/Freezers: Track internal temperatures for food or medicine storage.
- Incubators/Greenhouses: Maintain optimal conditions for plants or eggs.
- Wine Cabinets: Ensure proper storage temperature for wine.
- Outdoor Monitoring: Place the probe outside a window to detect outdoor temperature.
Note: The external probe only supports temperature measurement, not humidity.




6.3. Temperature Unit Switch
You can switch the temperature unit between Fahrenheit (°F) and Celsius (°C) within the Smart Life app settings.
6.4. Smart Linkage (Automation)
Create automation scenes with other Tuya smart devices based on temperature and humidity readings. The sensor uses an "Edge Triggered" principle, meaning an action is triggered only when the condition crosses the set threshold.
- Example 1: Air Conditioner Control
If the environment temperature rises from below 25°C to 25°C or above, the air conditioner can be set to turn on automatically. If the temperature remains above 25°C, the action will not re-trigger until the temperature drops below 25°C and then rises again. - Example 2: Humidifier Control
If the environment humidity reaches a preset low range, a smart humidifier can be set to turn on/off automatically.

Example of setting up smart linkage with an air conditioner in the app.

Example of setting up smart linkage with a humidifier in the app.
6.5. Temperature & Humidity Alarm
You can preset specific temperature and humidity ranges in the app. If the environmental temperature or humidity falls outside these ranges, you will receive instant alarm messages on your mobile device.

App interface for configuring temperature and humidity alarms.
6.6. Third-party Voice Control
The sensor supports voice queries for environmental temperature and humidity via smart speakers like Amazon Alexa and Google Speaker. Due to the nature of these devices, direct control panels for temperature/humidity sensors may not be displayed normally in their respective apps, but voice commands are supported.
- To enable: Link your Smart Life account to the third-party smart speaker app via the "Skill" function (Smart Life App > Me > Third-Party Services).
- Note: Route or automatic processes related to temperature and humidity cannot be established directly on third-party smart speakers.
- The device does not support Yandex Alice.
7. Maintenance
7.1. Battery Replacement
The device features a low battery automatic reminder. When the battery power is low, an alarm message will be pushed via the app, reminding you to change the batteries.

App notification for low battery.
- Replace with two fresh LR03-1.5V/AAA alkaline batteries.
- Purchase high-quality, genuine batteries from reputable stores to ensure optimal performance and battery life.
7.2. Cleaning
Wipe the sensor unit and external probe with a dry, soft cloth. Do not use liquid cleaners or immerse the device in water.
8. Troubleshooting (FAQ)
8.1. Accuracy and Data Reporting
- When is the temperature and humidity most accurate?
Approximately 30 minutes after configuration, the temperature and humidity readings will be closer to the actual ambient environment. - How often does the device report data?
The sensor uses a trigger mechanism. Data is reported immediately if the environmental temperature changes by ≥ 0.5°C or humidity changes by ≥ 5%. Otherwise, data is reported approximately every 1 hour. The fastest update frequency is two minutes. - Temperature/Humidity Error: All sensors have some error. This sensor has an error of ±1°C for temperature and ±5%RH for humidity. Readings within these ranges are considered normal.
- Probe Temperature Accuracy: For -10℃~50℃, accuracy is 0.25°C, reporting immediately if temperature changes by ≥ ±1.5°C. Outside this range, accuracy is 1°C, reporting immediately if temperature changes by ≥ ±2°C.
8.2. Network Connectivity
- Why does the network testing function in the app often fail?
To conserve battery, the sensor enters a sleep mode and disconnects from the network when not actively reporting data. Network testing requires continuous online status, which would rapidly deplete the battery. The sensor will automatically wake up and connect when data needs to be reported or when a significant change in temperature/humidity occurs.
8.3. Configuration Failure
If you encounter issues during device configuration, try the following steps:
- Restart your Wi-Fi router and try again.
- Ensure your mobile device is connected to a 2.4GHz Wi-Fi network.
- Verify that the Smart Life app has Bluetooth permissions enabled and that your phone's Bluetooth is turned on. If your phone uses low-power Bluetooth with GPS, ensure location services are also enabled.
- Check your network connectivity to ensure your router is functioning correctly.
- Double-check that the Wi-Fi password entered during setup is correct.
- Confirm that your Wi-Fi router does not have restricted access features, such as a MAC address whitelist, that might block the device.
- If your 2.4GHz and 5GHz Wi-Fi networks share the same SSID (name), try changing the SSID of the 2.4GHz network and connect your smartphone to it specifically.
- If configuration still fails, turn off your phone's Bluetooth, then press and hold the sensor's reset button for 5 seconds until the indicator light blinks slowly. Then, try adding the device using AP mode (select the slow blinking option in the app).
8.4. Probe Lead Extension
While theoretically possible to extend the probe lead, it is not officially supported or recommended. Extending the lead may affect resistance and require calibration, potentially impacting accuracy and reliability.
9. User Tips
- This sensor is highly effective for monitoring conditions in aquariums, greenhouses, wine cellars, and refrigerated display cases.
- The device integrates well with popular smart home platforms like Home Assistant (via Zigbee2MQTT or ZHA) and SmartThings.
- Expect initial readings to stabilize after about 30 minutes as the sensor adjusts to the environment.
- The sensor can be mounted on a desk, pasted to a wall with adhesive tape, or adsorbed onto a refrigerator using a magnet sticker for versatile placement.


10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the seller's policies or contact the manufacturer directly. Keep your purchase receipt for any warranty claims.
