Godox iT20 R

Contents

Godox iT20 R Mini Flash for Ricoh

Instruction Manual

Introduction

Thank you for purchasing the Godox iT20 R Mini Flash. This ultra-compact camera flash is designed for Ricoh GR3 and GR3X cameras, offering advanced features like TTL auto flash and manual flash modes. Its small size allows for direct insertion into the camera's hot shoe, making it an invisible partner for your photography needs. This manual provides detailed instructions for safe and effective use of your iT20 R flash.

For a more detailed manual, please refer to the official PDF document: Godox iT20 R User Manual (PDF)

Important Safety Instructions

This product is professional photographic equipment and should be operated by professional personnel only. Please read and understand all safety instructions before use.

  • Always read and fully understand the instruction manual before use.
  • This is not a toy; children are prohibited from using it. Adult supervision is required when children are near the device.
  • This is not for general illumination. Avoid direct eye contact with the flash, especially for babies.
  • Do not touch hot parts of the flash to avoid burns.
  • If the flash tube is damaged, stop use immediately and contact service for replacement.
  • Do not use damaged equipment or accessories.
  • Stop use immediately if the product casing is cracked due to falling or impact.
  • The device is not waterproof. Keep it dry and avoid immersing it in water or other liquids.
  • Do not disassemble the product without authorization. Repairs must be performed by authorized personnel.
  • Ensure the device is completely cooled before storage.
  • Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases.
  • Do not use or store this device in potentially explosive environments.
  • Use only accessories approved by Godox.
  • Clean gently with a dry cloth.

Battery Safety Precautions

  • Use only the specified charger and follow proper charging instructions within the rated voltage and temperature range.
  • Lithium batteries have a limited lifespan (typically 300-500 complete charge-discharge cycles). Regularly check the battery's condition.
  • For storage, charge the battery to approximately 50% capacity. Recharge to 50% at least every six months to prevent permanent performance degradation.
  • Do not disassemble, crush, or puncture the battery.
  • The battery is not waterproof; do not immerse it in water.
  • Avoid short-circuiting the battery contacts.
  • Do not expose the battery to fire or temperatures above 60°C.
  • Keep out of reach of children.
  • Avoid excessive shock or vibration.
  • Do not use a damaged battery.
  • If the battery leaks, avoid contact with the leaking fluid. If fluid contacts eyes, rinse immediately with water for at least 15 minutes and seek medical attention.
  • Comply with all relevant local laws and regulations when handling batteries.

What's Included

The package for your Godox iT20 R Mini Flash typically includes the following items:

  • Flash Body x1
  • USB-C Charging Cable x1
  • Storage Bag x1
  • Instruction Manual x1
  • Magnetic Spreader x1
  • Magnetic Color Filter x2

Separately Sold Accessories:

  • Magnetic Accessory for Flash Camera Flash MA01
  • Diffuser for iT20/iT22-DF
Godox iT20 R Mini Flash with accessories

Image: The Godox iT20 R Mini Flash in black and silver, shown with included magnetic color filters, a magnetic spreader, and a USB-C charging cable.

Setup

Parts of the Flash

  1. USB-C Charging Port
  2. Power Switch/Test Button
  3. M Button
  4. Display
  5. +/- Buttons
  6. Hot Shoe
  7. Detach Button
  8. Flash Tube
Godox iT20/iT22 Mini Flashes

Image: Three Godox iT20/iT22 mini flashes in different colors, highlighting their compact design.

Installing and Disassembling the Camera Flash

Important: Ensure both the camera and the flash are powered off before installation or disassembly.

  • Installation: Insert the camera flash into the camera's hot shoe parallelly until it is firmly locked.
  • Disassembly: Press and hold the detach button, then pull the flash parallelly from the camera's hot shoe.
Godox iT20 R mounted on a camera

Image: The Godox iT20 R flash mounted on a Ricoh camera, demonstrating its compact fit.

Power On/Off and Test Button

  • Power On: Press and hold the Power Switch/Test Button until the screen lights up.
  • Power Off: Press and hold the Power Switch/Test Button until the screen blacks out.
  • Testing: After powering on, short press the Power Switch/Test Button to fire a test flash.

Operating Instructions

TTL Auto Flash Mode

In TTL mode, the flash automatically adjusts its output for correct exposure.

  • Press the M button to switch to TTL mode. The display panel will show "TTL".
  • Use the +/- buttons to adjust Flash Exposure Compensation (FEC) from -3.0 to +3.0 in 1/3 stop increments. Press and hold the buttons for quick adjustment.
  • If the "MAX" icon is displayed, it indicates maximum flash output. Adjust camera parameters if underexposure still occurs.
Godox iT20 R controls for M and TTL modes

Image: Close-up view of the Godox iT20 R's control panel, showing the 'M' button and 'MODE' button for switching between manual and TTL modes, along with exposure compensation display.

Manual Flash Mode

In Manual mode, you set the flash output power yourself.

  • Press the M button to switch to Manual mode. The display panel will show "M".
  • Use the +/- buttons to adjust the flash power from 1/32 to 1/1 (full power) in 1/3 stop increments. Press and hold the buttons for quick adjustment.

Battery Level Indication

The battery level is indicated by an icon on the display. A three-grid icon means full battery. Please recharge the battery when only one grid remains.

Auto Off Function

The device will automatically power off after 60 minutes of idling if it is not connected to a camera in sleep mode.

Magnetic Accessories

The Godox iT20 R supports magnetic accessories for creative lighting. These can be easily attached to the flash head.

Godox iT20 R with magnetic accessories

Image: The Godox iT20 R flash shown with various magnetic accessories, including diffusers and color filters, demonstrating how they attach to the flash head.

Maintenance

Cleaning

Clean the device gently with a dry cloth. Do not use a wet cloth, as it may damage the device.

Battery Maintenance and Storage

Refer to the "Battery Safety Precautions" in the Important Safety Instructions section for detailed guidelines on charging, storage, and handling of the built-in lithium battery.

  • Regularly check the battery's condition. If charging time significantly increases or battery life decreases, consider replacing it.
  • For long-term storage, charge the battery to approximately 50% capacity. Recharge to 50% at least every six months.

Troubleshooting

Over-Temperature Protection

To prevent overheating and damage to the flash head, avoid firing more than the recommended number of continuous flashes at full power. If the over-temperature protection function is activated, the recycling time may increase to over 10 seconds. Allow approximately 10 minutes for the flash unit to cool down and return to normal operation. The display will show "Over-temperature" when active.

Continuous Flashes Before Over-Temperature Protection:

Flash Power Max Continuous Flashes
1/1 40
1/2 60
1/4 100
1/8 200
1/16 300
1/32 400

Fault Code Explanation

The system continuously performs preventive protection. If an abnormality occurs, the display will show a corresponding warning code. Refer to the table below for guidance:

Warning Code Description Solution
E1 Recycling time too long Contact service
E2 Main circuit temperature too high Stop triggering for approximately 10 minutes
E3 Flash tube temperature too high Stop triggering for approximately 10 minutes
E4 The device may have a failure Contact service

Specifications

Feature Specification
Model iT20 R
Compatible Cameras Ricoh GR3/GR3X
Guide No. (1/1 output) GN12 (ISO100, 1m)
Flash Coverage 28mm (fixed)
Flash Duration 1/300s - 1/20000s
Exposure Control System TTL Auto Flash, Manual Flash
Flash Exposure Compensation (FEC) Manual. ±3 stops in 1/3 stop increments
Sync Mode Front curtain sync
Recycling Time Approx. 1.5s (full power)
Flashes at Full Power Approx. 700
Power Source Built-in 3.7V 350mAh Lithium battery
Dimensions 45 x 28 x 28 mm
Net Weight 45 g
High-speed synchronous (HSS) No
Display Yes
Godox iT20 R detailed specifications and features

Image: A comprehensive graphic detailing the features, specifications, and various modes of the Godox iT20 R flash.

User Tips

  • The iT20 R offers excellent functionality and control, especially for Ricoh GR series cameras like the GRIII and GRIV.
  • Experiment with the magnetic flash attachments (diffusers and color filters) to unleash creativity and achieve different lighting effects.

Frequently Asked Questions (FAQ)

No specific FAQ content is available at this time. Please refer to the instruction manual or contact customer support for assistance.

Warranty and Support

Warranty Information

The Godox iT20 R Mini Flash comes with a warranty. Please retain your warranty card as it is an important certificate for maintenance service.

Warranty Period:

  • Main Device: 1 year
  • Battery: 3 months
  • Electrical Parts (e.g., charger): 12 months
  • Consumables (e.g., flash tube, lamp body, cover, locking device, packaging): No warranty

The warranty period is calculated from the date of purchase as registered on the warranty card.

How to Obtain Maintenance Service

If maintenance service is required, you can directly contact the product distributor or authorized service institutions. You may also contact Godox after-sale service directly. When applying for service, you must provide a valid warranty card. If a valid warranty card cannot be provided, service may still be offered if the product is confirmed to be within the maintenance scope, but this will not be considered an obligation.

Inapplicable Cases

The warranty and service provided by this document are not applicable in the following cases:

  • Product or accessory has expired its warranty period.
  • Breakage or damage caused by inappropriate usage, maintenance, or preservation (e.g., improper packing, improper external equipment connection, falling off, squeezing, exposure to improper temperature, solvents, acids, water, or damp environments).
  • Breakage or damage caused by non-authorized installation, maintenance, alteration, addition, or detachment.
  • Original identifying information of the product or accessory is modified, altered, or removed.
  • No valid warranty card.
  • Breakage or damage caused by using illegally authorized, non-standard, or non-publicly released software.
  • Breakage or damage caused by force majeure or accident.
  • Breakage or damage that cannot be attributed to the product itself.
  • Normal discoloration, abrasion, and consumption due to use.

© 2023 Godox. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.