RACBOX LED Side Marker Signal Light

Contents

RACBOX 12V 24V LED Dual Color Clearance Light User Manual

Model: LED Side Marker Signal Light

1. Product Overview

The RACBOX 12V 24V LED Dual Color Clearance Light is an auxiliary accessory designed for automotive lighting. It functions as a clearance light, rear brake indicator, and turn signal lamp, featuring 12 LEDs per lamp with dual red and white color output. This product is suitable for a wide range of vehicles including trucks, trailers, campers, vans, boats, pickups, and off-road vehicles.

Multiple RACBOX LED Dual Color Clearance Lights
RACBOX LED Dual Color Clearance Lights, showcasing their design and illumination.

2. Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Specifications

Feature Detail
Product Type LED Brake Signal Light / Clearance Lights Assembly
Input Voltage DC 10-30V (compatible with 12V and 24V systems)
Light Color Red + White (Dual Color)
LED Quantity 12 LEDs per lamp
Material ABS
Dimensions (approx.) 73mm (Length) x 37.6mm (Width) x 26mm (Height of light portion)
Mounting Stud Spacing (approx.) 37mm
Package Weight (approx.) 0.145 kg
Origin Mainland China
Product size diagram showing dimensions in millimeters
Detailed product dimensions for installation planning.

4. Setup (Installation Instructions)

Follow these steps for proper installation of your LED Dual Color Clearance Light:

  1. Turn off the vehicle engine and disconnect the power supply to avoid short circuit.
  2. Locate the mounting position of the original clearance lights assembly.
  3. Remove the fixing screws or clips that hold the stock light assembly.
  4. Unplug the power connector and take off the original clearance lights assembly.
  5. Install the new clearance lights assembly into the mounting position.
  6. Secure the light assembly with screws or clips to ensure stable installation.
  7. Connect the power plug correctly. If the light does not work, reverse the plug polarity.

Wiring Diagram:

3-wire connection diagram for the LED light
The 3-wire connection: Red for Red Light, White for White Light, Black for Negative.
LED light with mounting hardware including screws and nuts
The LED light assembly includes necessary mounting hardware for secure installation.

5. Operating Instructions

Once installed and wired correctly, the LED Dual Color Clearance Light will operate based on the electrical signals from your vehicle. The 3-wire connection allows for distinct red and white light functions.

  1. Test all light functions to ensure normal operation.
  2. Verify that the red light illuminates for brake/turn signal functions and the white light for clearance/reverse functions, depending on your vehicle's wiring configuration.
Images showing the LED light illuminating in red, white, and dual red-white modes
The light can display red, white, or a combination of both colors based on wiring.
LED lights installed and illuminated on a trailer at night
Example of the LED lights installed and functioning on a trailer.

6. Maintenance

To ensure the longevity and optimal performance of your LED lights, follow these maintenance guidelines:

  • Recheck all screws and connections periodically to make sure they are firm and reliable. Loose connections can lead to intermittent operation or failure.
  • Clean the light lenses regularly with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners that could scratch the lens.
  • Inspect wiring for any signs of wear, fraying, or damage. Replace damaged wiring immediately to prevent short circuits.
  • Ensure the lights are not exposed to excessive water or moisture, as this product is not designed for submersion.

7. Troubleshooting

  • Light does not illuminate:
    • Check power connections. Ensure wires are securely connected to the correct terminals.
    • If the light does not work, reverse the plug polarity. LED lights are polarity sensitive.
    • Verify that the vehicle's power supply (10-30V DC) is active and within the specified range.
    • Inspect the light for any visible damage.
  • Intermittent operation:
    • Check for loose wiring connections at both the light and the vehicle's power source.
    • Ensure mounting screws are tight and the light is securely fastened.
  • One color not working (e.g., only red or only white):
    • Verify the specific wire for the non-functioning color is correctly connected and receiving power.
    • Check for any breaks or damage in the individual color wire.

8. User Tips

  • Before final installation, temporarily connect the lights to a power source to confirm functionality and correct polarity.
  • Consider using waterproof electrical connectors for enhanced durability, especially in marine or harsh weather environments.
  • When replacing existing lights, ensure the new RACBOX lights match the intended function (e.g., brake, turn, clearance) and wiring of the original setup.

9. Frequently Asked Questions (FAQ)

Q: What vehicles are these lights compatible with?
A: These lights are universal and compatible with trucks, trailers, campers, vans, boats, pickups, and off-road vehicles that operate on a DC 10-30V electrical system.
Q: How do I switch between red and white light?
A: The lights have a 3-wire connection. The red wire controls the red light, and the white wire controls the white light. The black wire is for the negative pole. The specific function (e.g., brake, turn, clearance) depends on how you integrate these wires into your vehicle's existing electrical system.
Q: What if the light doesn't turn on after installation?
A: First, check all wire connections to ensure they are secure. If still not working, try reversing the polarity of the power plug, as LED lights can be sensitive to polarity.

10. Warranty & Support

This product is an auxiliary accessory for automotive lighting and is intended for normal replacement and upgrade of original car lights. It meets relevant national automotive lighting industry standards and has undergone strict quality testing.

For detailed manufacturer information and EU authorized representative details, please refer to the official product manual PDF available at this link.

Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd.

EU Authorized Representative: APEX CE SPECIALISTS LIMITED

© 2024 RACBOX. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.