HOMEFISH HW-401A

Contents

HOMEFISH HW-401A Handheld Battery Spot Welder User Manual

Model: HW-401A

1. Safety Information

Please read the following safety information carefully before using the product to avoid equipment damage, personal injury, or property loss.

  1. Power Connection: Use a power adapter matching the product's rated voltage (preferably original or genuine brand adapters). Avoid fast-charging devices (if not marked as fast-charge compatible) to prevent circuit overload, short circuits, fires, or electric shocks.
  2. Environmental Requirements: Do not place the product in high-temperature (>60°C, e.g., direct sunlight, near ovens), humid (rainy days, bathrooms), dusty, or strong magnetic field environments. This may cause malfunctions, battery swelling, or performance degradation.
  3. Child Supervision: Children under 12 must be supervised by adults when using the product. Prevent accidental ingestion of small parts, contact with power interfaces, and avoid excessive volume or prolonged use that may damage eyesight/hearing.
  4. Prohibition of Modification: Do not disassemble, modify, or repair the product yourself. Disassembly may cause battery leakage or short circuits and will void the warranty.
  5. Abnormal Handling: If the product shows overheating, abnormal noise, peculiar odors, smoke, or electric leakage, immediately disconnect power/stop use, keep it away from flammables, and do not disassemble it yourself.
  6. Battery Safety: Do not short-circuit, squeeze, or incinerate removable batteries. Dispose of waste batteries in accordance with local environmental regulations; do not mix with household garbage. For built-in batteries, charge to 50%-70% if unused for over 1 month and recharge regularly.

Warning: Strictly follow these safety norms to avoid personal injury and property loss. Do not overload or misuse the product. Wear protective gloves and goggles during operation to prevent scratches or debris hazards. Do not use the product as a hammer or pry bar to avoid breakage. Minors are prohibited from use. Adults must concentrate and avoid operation under the influence of alcohol or fatigue.

2. Product Overview

The HOMEFISH HW-401A is a portable handheld spot welding machine designed for welding nickel sheets and strips to 18650 lithium batteries. It features adjustable power levels and convenient USB charging.

HOMEFISH Handheld Battery Spot Welder

Image: HOMEFISH Handheld Battery Spot Welder with key features.

Key Features:

  • Five Power Adjustable Levels: Allows for precise welding based on material thickness.
  • 5V USB Charging: Convenient and widely compatible charging method.
  • Welding Thickness: Supports nickel sheet thickness from 0.1mm to 0.2mm.
  • High Efficiency: Can perform over 800 welds on a single full charge.
  • Easy to Use: Designed for one-hand operation with intelligent identification and fully automatic welding.
Control Panel of HW-401A Spot Welder

Image: Control panel showing ON/OFF, Gear (power level), Energy (battery indicator), and 5V Type-C charging port.

3. Setup

3.1 Package Contents

Before first use, please verify that all items are present in the package:

  • HOMEFISH HW-401A Spot Welder Unit
  • USB Charging Cable
  • Nickel Strip Sample
  • User Manual (this document)
HW-401A Package Contents

Image: Contents of the HW-401A package.

3.2 Initial Charging

It is recommended to fully charge the device before its first use to ensure optimal performance and battery longevity.

  1. Connect the included USB charging cable to the Type-C port on the spot welder.
  2. Plug the other end of the USB cable into a compatible 5V USB power adapter (not included).
  3. The indicator light will typically stay red during charging. It will turn green/blue or go off when fully charged.
  4. Once fully charged, unplug the cable from the device and the power adapter.
HW-401A Charging

Image: HW-401A spot welder connected to a USB charging cable.

4. Operating Instructions

4.1 Power On/Off

  • To Power On: Press and hold the ON/OFF button (refer to the control panel image in Section 2) for a few seconds until the indicator lights illuminate.
  • To Power Off: Press and hold the ON/OFF button again until the indicator lights turn off.

4.2 Adjusting Power Levels

The HW-401A features five adjustable power levels (Gears) to accommodate different welding needs. The current power level is indicated by the 'Gear' lights on the control panel.

  • After powering on, short-press the ON/OFF button to cycle through the 5 power levels.
  • Start with a lower power setting for thinner materials and increase as needed. Always test on scrap material first.

4.3 Welding Process

  1. Preparation: Ensure the battery terminals and nickel strip are clean and free from oxidation or debris. Wear appropriate safety goggles and gloves.
  2. Power On and Select Level: Power on the spot welder and select the desired power level. For 0.1mm nickel, level 1 or 2 is often sufficient. For 0.15mm, level 3. For 0.2mm, level 4 or 5.
  3. Positioning: Place the nickel strip firmly against the battery terminal where you intend to weld.
  4. Welding: Place both copper welding tips firmly and squarely onto the nickel strip, ensuring good contact. The welder will automatically detect contact and initiate the weld. You will hear a small spark and see a flash.
  5. Inspect Weld: After welding, gently try to peel off the nickel strip to check the weld strength. If it peels easily, increase the power level and try again. A good weld will tear the nickel strip before detaching from the battery.
Solder Joint Effect

Image: Examples of successful spot welds on battery packs.

5. Maintenance

5.1 Cleaning

  • Always disconnect power before cleaning.
  • Wipe the device with a dry, soft cloth.
  • Avoid using corrosive liquids (e.g., alcohol, disinfectant) to prevent damage to the casing or internal components.

5.2 Storage

  • Clean the product thoroughly before long-term storage.
  • Store in a dry, well-ventilated place.
  • Avoid extrusion or impact on the device.
  • If storing for over a month, charge the internal battery to 50-70% and recharge regularly to maintain battery health.

5.3 Inspection

  • Regularly check the USB charging cable and welding tips for any signs of damage or wear.
  • If any damage is found, stop use immediately and replace the damaged component if possible, or contact support.

6. Troubleshooting

  • Poor or Weak Welds:
    • Ensure battery terminals and nickel strips are clean.
    • Increase the power level (Gear setting).
    • Apply firm and even pressure on both welding tips.
    • Ensure the battery is sufficiently charged.
  • Device Not Powering On:
    • Check battery level; recharge if low.
    • Ensure the power button is pressed and held for the correct duration.
  • Device Overheating or Abnormal Behavior:
    • Immediately power off the device and disconnect from any power source.
    • Allow the device to cool down completely.
    • If abnormal behavior persists (e.g., smoke, peculiar odors), discontinue use and refer to the 'Abnormal Handling' section in Safety Information.

7. Specifications

FeatureSpecification
ModelHW-401A
Welding Thickness (Nickel)0.1mm - 0.2mm
Power Levels5 Adjustable Gears
Charging Input5V via Type-C USB
Welds Per Charge800+ times
Approximate Battery LifeUp to 10 hours (general usage, may vary with high-power functions)
Length24.3 cm (9.56 in)
Tip Width5.7 cm (2.24 in)
Height2.5 cm (0.98 in)
Package Weight0.386 kg
HW-401A Dimensions

Image: Dimensions of the HW-401A spot welder.

8. User Tips

  • Always ensure the device is fully charged before starting a welding project for consistent performance.
  • For 0.1mm nickel strips, users often find success with power levels 1 or 2. For 0.15mm, level 3 is commonly used.
  • The device is capable of welding up to 0.20mm nickel strips effectively. Some users report success with slightly thicker materials at maximum power, but always test on scrap material first.
  • Practice on scrap batteries and nickel strips to find the optimal power level and pressure for your specific materials before working on your main project.

9. Warranty & Support

9.1 Disclaimer

  • The manufacturer is not liable for product malfunctions caused by force majeure (e.g., earthquakes, fires, natural disasters), improper use, overload, third-party damage, or cross-border transportation accidents.
  • Warranty is void if the product is disassembled, modified, repaired with non-original parts, or improperly repaired—no liability is assumed for resulting damage.
  • This manual provides installation, operation, and maintenance guidance. Product parameters and functions may change with version updates—please refer to the actual product.

9.2 Further Information

For more detailed information, please refer to the official PDF user manual: View PDF Manual

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.