1. Important Safety Information
Please read all instructions carefully before using this product. Failure to follow these instructions may result in product damage or personal injury.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Keep the device out of reach of children.
- Do not use this product for purposes other than its intended use.
For a complete list of safety warnings and compliance information, please refer to the official user manual PDF available from the seller.
2. Setup and Installation
This step-down converter is designed for easy integration into your electrical system. Ensure all power sources are disconnected before making any connections.
Wiring Instructions:
- Input Positive (+): Connect the Red wire to your 24V DC power source positive terminal.
- Input Negative (-): Connect the Black wire (from the input side) to your 24V DC power source negative terminal.
- Output Positive (+): Connect the Yellow wire to the positive terminal of your 12V DC device.
- Output Negative (-): Connect the Black wire (from the output side) to the negative terminal of your 12V DC device.
Figure 1: Wiring Diagram. Connect input wires to the 24V source and output wires to your 12V load. Note: The diagram illustrates general connections; ensure your load is 12V compatible.
Mounting:
The converter features mounting holes for secure installation. Use appropriate fasteners for your application.
- Mounting Hole Distance: 51mm
- Aperture: 4mm
3. Operating Instructions
Once properly wired, the converter will automatically step down the input voltage. There are no user-adjustable settings or controls.
- Ensure your input voltage is within the specified range (15-40V DC).
- Connect your 12V DC load, ensuring it does not exceed the maximum output current of 5A (60W).
- Apply power to the input terminals. The converter will then provide a stable 12V output.
Caution: Exceeding the maximum output power or current may damage the converter or the connected device.
4. Maintenance
The GYVRM-K241205 converter is designed for durability and requires minimal maintenance.
- Keep the device clean and free from dust and debris.
- Ensure it is stored and operated in a dry environment, away from moisture.
- Avoid exposing the converter to extreme temperatures.
5. Troubleshooting
If you experience issues with your converter, consider the following steps:
- No Output Voltage:
- Verify that the input voltage is present and within the 15-40V range.
- Check all wiring connections for proper polarity and secure contact.
- Ensure the converter is not damaged (e.g., from physical impact or overheating).
- Incorrect Output Voltage or Unstable Operation:
- Confirm the input voltage is stable and within the specified range.
- Ensure the load connected does not exceed the maximum 5A (60W) output capacity.
- Check for any short circuits in the output wiring or the connected device.
If problems persist, discontinue use and contact the seller for support.
6. Specifications
| Model | GYVRM-K241205 |
| Input Voltage Range | 15V - 40V DC |
| Output Voltage | 12V DC |
| Output Current | 5A (Max) |
| Output Power | 60W (Max) |
| Conversion Efficiency | 96% |
| Dimensions (L x W x H) | 51mm x 20mm x 24.5mm (2.0in x 0.8in x 1.0in) |
| Weight | Approx. 41g (1.4oz) |
| Mounting Hole Distance | 51mm |
| Mounting Aperture | 4mm |
| Features | Synchronous voltage stabilization, low heat, stable performance, waterproof, dustproof, anti-shock |
Figure 2: Product Dimensions. Visual representation of the converter's physical size.
7. User Tips
- Always verify your input voltage with a multimeter before connecting the converter to prevent damage.
- Ensure the total power consumption of your 12V devices does not exceed 60W to maintain optimal performance and longevity of the converter.
- For permanent installations, consider using appropriate strain relief for the wiring to prevent accidental disconnections or damage.
8. Warranty and Support
For warranty information, returns, or technical support, please contact your original seller or retailer. Keep your proof of purchase for any warranty claims.
Manufacturer Information:
- Manufacturer: Tai'an Anbang International Trade Co., Ltd, No.959 North Tianmen Street, Tai'an High tech Development Zone, Shandong, China.
- Manufacturer Email: 2777053327@qq.com
- EU Authorized Representative: Kqu Thnolog s.r.o., Rakova 108/69, Tic, 90000. Jihomoravský kraj, Czech Republic Brno City South Moravian Region.
- EU Representative Email: christopher25106@outlook.com
Compliance:
This product complies with KCE FC standards.