1. Product Overview
The CILIA Model 5704 is an IP54-rated outdoor waterproof power strip designed for use in various environments. This power strip features four EU/German type outlets and requires user wiring for connection to a power source. It is designed for a maximum power output of 3500W.

Figure 1: Front view of the CILIA Model 5704 power strip with protective caps closed.
2. Safety Precautions
- Electrical Safety: Always ensure the power strip is disconnected from the main power supply before performing any wiring, maintenance, or inspection. If you are unsure about electrical wiring, consult a qualified electrician.
- Dry Conditions: When connecting devices or using the power strip, ensure that all plugs and the power strip itself are completely dry, especially when used in damp environments.
- Overload Protection: Do not exceed the rated maximum power of 3500W or rated current of 16A to prevent damage to devices or safety hazards.
- Flammable Materials: Do not place flammable materials on or near the power strip to prevent the risk of fire.
- Inspection: Regularly check the power strip and its connecting cables for any signs of wear, damage, or aging. Discontinue use if any damage is found.
- Outdoor Use: While rated IP54, ensure all outlet caps are securely closed when not in use to maintain water resistance.
3. Setup and Wiring Instructions
This power strip is supplied without pre-attached wires. You will need to connect your own power cable according to your desired length and local electrical standards.
- Prepare the Power Cable: Obtain a suitable 3-core cable (e.g., 3x1.5mm² for German plugs) with appropriate insulation and length for your application.
- Access Wiring Terminal: Locate the screw cover at one end of the power strip. Carefully open this cover to expose the internal wiring terminals.
- Wire Connection: Following the diagram below, connect the Live (L), Neutral (N), and Ground wires from your power cable to the corresponding terminals inside the power strip. Ensure all connections are secure and no bare wire strands are exposed outside the terminals.

Figure 2: Internal view of the power strip with cover open, showing bus bars and contacts.

Figure 3: Wiring diagram. Connect Live (L), Neutral (N), and Ground wires as shown.
- Secure Cable Entry: Ensure the cable is properly routed through the cable gland/seal at the end of the power strip to maintain its IP54 rating. Tighten the gland to secure the cable and provide strain relief.
- Close Cover: Carefully replace and secure the screw cover over the wiring terminals.
- Initial Check: Before plugging into a power source, visually inspect all connections and ensure the power strip is fully assembled and dry.
4. Operating Instructions
- Connect to Power: Plug the wired power strip into a suitable wall socket.
- Connect Devices: Open the protective cap of the desired outlet. Insert the plug of your device firmly into the power strip outlet.
- Secure Unused Outlets: Always ensure that the protective caps on all unused outlets are securely closed, especially when the power strip is used outdoors or in damp conditions, to maintain its IP54 waterproof rating.
- Monitor Load: Ensure the total power consumption of all connected devices does not exceed 3500W (16A at 250V).
5. Maintenance
- Regular Inspection: Periodically inspect the power strip and its connecting cable for any signs of physical damage, cracks, fraying, or discoloration.
- Cleaning: Disconnect the power strip from the main power supply before cleaning. Wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners, solvents, or immerse the unit in water.
- Cap Integrity: Ensure the protective caps remain flexible and seal properly. Replace the unit if caps are damaged or no longer provide a secure seal.
6. Troubleshooting
- No Power to Devices:
- Check if the power strip is properly plugged into the wall socket.
- Verify that the wall socket itself is live (test with another device).
- Inspect the power strip and its wiring for any visible damage.
- Devices Trip Circuit Breaker:
- The total power consumption of connected devices may exceed the power strip's 3500W limit or the circuit's capacity. Unplug some devices and try again.
- Ensure your devices are compatible with the 250V supply.
- Water Ingress: If you suspect water has entered the power strip, immediately disconnect it from power and allow it to dry completely in a safe, well-ventilated area before attempting to use it again. If damage is suspected, discontinue use.
7. Specifications
| Model | 5704 |
| Outlets | 4 (EU/German Type) |
| Rated Current | 16A |
| Rated Voltage | 250V |
| Maximum Power | 3500W |
| IP Rating | IP54 (Dust and Splash Water Protected) |
| Frame Material | TPE (Thermoplastic Elastomer) |
| Bottom Cover Material | High-temperature resistant, flame-retardant PC (Polycarbonate) |
| Plug Type | Universal (for EU/German standard) |
| Dimensions (L x W x D) | 27.2 cm x 6.3 cm x 4.4 cm (approx. 10.7 in x 2.48 in x 1.73 in) |

Figure 4: Dimensions of the CILIA Model 5704 power strip.
8. User Tips
- DIY Wiring: Take your time when wiring the power strip. Double-check all connections before closing the cover and applying power.
- Application Suitability: While this power strip is waterproof, consider its intended use. For heavy-duty workshop environments requiring extreme robustness, you may need to evaluate if this product meets those specific demands.
- Device Compatibility: Always ensure that the devices you connect are within the power strip's rated current and voltage limits to prevent damage to both the power strip and your appliances.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the original seller or manufacturer's documentation provided at the time of purchase. Keep your proof of purchase for any warranty claims.
A PDF version of this user manual may be available from the seller for detailed reference.