TUMMASTER AK350/AK390

Contents

TUMMASTER ARGB Water Cooling Sleeve Instruction Manual

Models: AK350, AK390

1. Product Overview

The TUMMASTER ARGB Water Cooling Sleeve is a soft silicone light-emitting tube designed to enhance the aesthetic of your PC case, particularly around water cooling systems. It features addressable RGB (ARGB) lighting, offering uniform illumination and 360-degree bend flexibility for custom DIY setups.

TUMMASTER ARGB Water Cooling Sleeve product overview
Product overview showing two ARGB water cooling sleeves with 5V-3PIN connectors. Key features include soft silicone material, uniform lighting, and 360-degree bend capability.
TUMMASTER ARGB Water Cooling Sleeve installed in a PC case
Example of the liquid cooling illuminated tube installed in a PC case, highlighting its soft silicone material, 360-degree bend, uniform lighting, and DIY customization.

2. Specifications

Feature AK-350 Model AK-390 Model
Brand Name TUMMASTER
Type TOOL (PC Case Decoration)
Power Interface 5V-3pin ARGB
RGB Support A-RGB
Lamp Length 13.78 inches (350mm) 15.35 inches (390mm)
Number of Lamp Beads 34 pcs 38 pcs
Inside Diameter 0.43 inches
Applicable Tube Length 16.14 inches 17.72 inches
Material Soft Silicone
Specifications for AK-350 model
Detailed specifications for the AK-350 model, including lamp length, number of beads, inside diameter, and applicable tube length.
Specifications for AK-390 model
Detailed specifications for the AK-390 model, including lamp length, number of beads, inside diameter, and applicable tube length.

3. Setup and Installation

The ARGB Water Cooling Sleeve is designed for easy installation around existing water cooling tubes. Its flexible silicone material allows for bending and shaping to fit various PC case configurations.

3.1 Components

  • ARGB Water Cooling Sleeve(s)
  • Snap Fasteners (clips)

3.2 Installation Steps

  1. Identify the water-cooling tubes within your PC case where you wish to install the sleeves.
  2. Carefully wrap the soft silicone sleeve directly around the water-cooling tubes. The material is flexible and can be bent to your desired shape.
  3. Secure the sleeves in place using the provided snap fasteners. Ensure the fasteners are firmly attached to prevent the sleeves from falling off due to vibrations or movement.
  4. Connect the 5V-3PIN ARGB connector from the sleeve to a compatible ARGB header on your motherboard or an ARGB controller. Ensure the connection is secure and correctly oriented (5V, Data, Ground).
  5. Organize cables to maintain good airflow and a tidy appearance within your PC case.
Easy installation diagram for ARGB water cooling sleeves
Diagram illustrating the easy installation process: soft silicone sleeves are wrapped around water-cooling tubes and secured with snap fasteners.

4. Operating Instructions

The TUMMASTER ARGB Water Cooling Sleeve utilizes a standard 5V-3pin ARGB connection, allowing for synchronization with various ARGB ecosystems.

4.1 Power and Connectivity

  • Ensure the 5V-3PIN ARGB connector is securely plugged into a compatible ARGB header on your motherboard or an external ARGB controller.
  • This product requires a 5V Addressable RGB header. Do NOT connect it to a 12V RGB header, as this may cause damage.

4.2 Lighting Control

Once connected, the lighting effects can be controlled via your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) or through the software provided with your external ARGB controller.

  • The sleeves feature high-density lamp beads for uniform lighting without dark shadows, providing vibrant and smooth illumination.
  • Experiment with different lighting modes, colors, and effects to personalize your PC build.
High density lamp beads for uniform ARGB lighting
Illustration of high-density lamp beads ensuring uniform lighting with no dark shadows, supporting 5V ARGB SYNC.

5. Maintenance

To ensure the longevity and optimal performance of your ARGB Water Cooling Sleeves, follow these simple maintenance guidelines:

  • Cleaning: Gently wipe the silicone sleeves with a soft, dry, or slightly damp cloth to remove dust and grime. Avoid using harsh chemicals or abrasive materials that could damage the silicone or LED components.
  • Inspection: Periodically check the snap fasteners to ensure they remain securely attached to the water-cooling tubes. Re-secure if any looseness is observed.
  • Cable Management: Ensure that the ARGB cables are not pinched or under excessive tension, which could lead to damage over time.
  • Environmental Conditions: Operate the product within typical indoor PC operating temperatures. Avoid extreme heat or direct sunlight for prolonged periods.

6. Troubleshooting

If you encounter issues with your ARGB Water Cooling Sleeves, consider the following troubleshooting steps:

6.1 Lights Not Turning On

  • Check Connections: Ensure the 5V-3PIN ARGB connector is fully and correctly seated into the motherboard header or ARGB controller. Verify that the 5V, Data, and Ground pins align.
  • Power Supply: Confirm that your ARGB controller or motherboard header is receiving power.
  • Software: Check your motherboard's ARGB control software to ensure the lighting is enabled and not set to an 'off' state or a very dim setting.
  • Compatibility: Double-check that you are connecting to a 5V-3pin ARGB header, not a 12V-4pin RGB header. Incorrect connection can damage the LEDs.

6.2 Incorrect Colors or Effects

  • Software Settings: Adjust the lighting effects and colors within your ARGB control software. Ensure the correct device is selected if you have multiple ARGB components.
  • Daisy Chain Order: If daisy-chaining multiple ARGB devices, ensure the order is correct and that the software recognizes all connected devices.

6.3 Sleeves Not Staying in Place

  • Fastener Security: Re-examine the snap fasteners. Ensure they are properly clipped and provide sufficient grip on the water-cooling tubes.
  • Additional Fasteners: If necessary, use additional snap fasteners to secure the sleeves more firmly, especially on longer or more complex bends.

7. Warranty and Support

For detailed warranty information and customer support, please refer to the official product documentation or contact the seller directly. A user manual in PDF format is available for download:

Download User Manual (PDF): Click Here

8. User Tips

Based on user experiences, here are some helpful tips for using your TUMMASTER ARGB Water Cooling Sleeves:

  • Aesthetics: Users frequently praise the great appearance and beautiful, vibrant colors of these sleeves, noting they work perfectly to enhance PC aesthetics.
  • Flexibility: The soft silicone material is highly flexible, allowing for creative bending and shaping to fit various custom PC builds.
  • Length Consideration: Some users have noted that while the product is excellent, an option for slightly longer sleeves (e.g., 420mm or 5cm longer than current models) would be beneficial for certain PC case configurations. Consider measuring your desired length carefully before purchase.
  • Packaging: While the product itself is generally well-received, some users have reported receiving packages with slightly crushed boxes. The product inside is typically unaffected, but it's worth noting.

© 2024 TUMMASTER. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.