Diymore Fan Temperature Control Board

Contents

Diymore DC Fan Controller Temperature Control Board User Manual

Model: Fan Temperature Control Board

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the Diymore DC Fan Controller Temperature Control Board. This module is designed to automatically regulate fan speed based on temperature, offering stable output and protection for the fan motor.

For a downloadable PDF version of this manual, please refer to the official user manual PDF.

Key Features

  • Supports 12-32V input voltage, suitable for various voltage applications.
  • Features a premium step-down circuit design for stable output and effective fan motor protection.
  • Modular design facilitates integration into diverse DIY projects and scenarios.
  • Solderless design requires no complex setup; simple wiring for easy operation.
  • Compact PCB design saves installation space; aluminum substrate aids heat dissipation.
Diymore Automatic Fan Controller with temperature probe and wires

Figure 1: Diymore Automatic Fan Controller, showcasing its step-down circuit design for stable output and fan motor protection.

Diymore Fan Controller PCB with temperature probe

Figure 2: Compact PCB design of the fan controller, highlighting its space-saving and heat dissipation features.

Specifications

ParameterValue
ModelFan Temperature Control Board
Input VoltageConstant Voltage 12-32V
Output VoltageDC12V
Sensing ElementThermistor Probe
Activation Temperature35°C (actual probe temperature determines activation)
Number of Fans Supported1 fan (multiple fans require corresponding number of controllers)
Recommended Fan Specifications12V 0.4A or less
Dimensions of the fan controller board

Figure 3: Physical dimensions of the Fan Temperature Control Board (20mm x 33mm).

Setup Instructions

  1. Identify Components: Unpack the fan controller module, temperature probe, and PH2.0 terminal wires (if included).
  2. Connect Power Input: Connect your 12-32V DC power source to the input terminals. Ensure correct polarity: 'V+' for positive and 'V-' for negative. The module features solderless PH2.0 connectors for direct insertion.
  3. Connect Fan Output: Connect your 12V fan to the output terminals. Ensure correct polarity: 'F+' for positive and 'F-' for negative. The module also uses solderless PH2.0 connectors for the fan connection.
  4. Connect Temperature Probe: Insert the thermistor probe into the designated probe interface on the board. This connection is also solderless.
  5. Position Temperature Probe: For optimal performance, attach the temperature probe to the component or area you wish to monitor and control the fan's temperature. Use thermally conductive adhesive for secure and efficient temperature sensing.
Interface Definition for the fan controller board

Figure 4: Detailed interface definition showing connections for Input Negative (V-), Input Positive (V+), Fan Negative (F-), Fan Positive (F+), and Probe Interface.

Solderless connectors on the fan controller board

Figure 5: Illustration of the solderless probe and PH2.0 connectors for easy wiring.

Operation

Once properly connected, the fan controller will automatically activate the connected fan when the temperature detected by the thermistor probe reaches approximately 35°C. The fan will continue to operate to cool the monitored area until the temperature drops below the activation threshold.

The actual activation temperature is determined by the probe's reading. Ensure the probe is correctly positioned for accurate temperature sensing.

Video 1: A brief overview of the DIY Fan Temperature Control Board, demonstrating its features and modular design.

Maintenance

  • Keep the module clean and free from dust and debris.
  • Ensure the module is installed in a dry environment to prevent moisture damage.
  • Periodically check all connections to ensure they are secure.
  • Inspect the temperature probe for any physical damage or corrosion.

Troubleshooting

  • Fan not activating:
    • Verify that the input voltage is within the 12-32V range and correctly connected.
    • Check the fan's power requirements; ensure it is 12V 0.4A or less.
    • Confirm the temperature probe is securely connected and positioned correctly to sense heat.
    • Ensure the ambient temperature around the probe is above 35°C for activation.
  • Fan running continuously:
    • Check if the temperature probe is correctly installed and not constantly exposed to high temperatures.
    • Ensure the fan is adequately cooling the area.
  • No power to the module:
    • Check the power supply connection and ensure it is providing the correct voltage.
    • Inspect the input wires for any breaks or loose connections.

User Tips

  • Always double-check wiring polarity before applying power to prevent damage to the module or connected components.
  • For optimal temperature control, ensure the thermistor probe is in direct contact with the heat source or the area requiring cooling.
  • If using multiple fans, remember that each fan requires its own dedicated temperature controller module.

Frequently Asked Questions (FAQ)

Q: What kind of temperature sensor is used?
A: The module uses a Thermistor Probe for temperature sensing.

Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.