MINEWSEMI ME25LS03

Contents

ME25LS03 SX1262 nRF54L15 Long Range LoRa Module

User Instruction Manual

Brand: MINEWSEMI | Model: ME25LS03

1. Introduction

The MINEWSEMI ME25LS03 is a high-performance, long-range, ultra-low-power, and compact wireless module designed for a wide array of IoT applications. It supports multiple protocols, including BLE 6.0 and LoRaWAN, and features 256 KB RAM and 1.5 MB Flash, providing ample storage for complex applications.

This module offers excellent receiver sensitivity, reaching -104 dBm (BLE) and -146 dBm (LoRa), with a maximum transmit power of +8 dBm (BLE) and +22 dBm (LoRa). This enables reliable long-distance communication. Powered at 3.3 V, the ME25LS03 includes a built-in 32 kHz crystal and provides a rich set of GPIO interfaces. Its fully open development platform supports customization and secondary development.

ME25LS03 module with MinewSemi logo and text 'Free technical support is provided'.

Figure 1: ME25LS03 Module Overview

2. Safety Information

  • Handle electronic components with care to avoid electrostatic discharge (ESD).
  • Ensure proper power supply voltage (1.7V-3.6V, recommended 3.3V) to prevent damage.
  • Avoid exposing the module to extreme temperatures or humidity outside its specified operating range.
  • Do not apply excessive mechanical stress or shock to the module.
  • Refer to the detailed datasheet for specific electrical and environmental limits.

3. Product Overview

3.1. Key Features

  • Dual-Core Architecture: Arm Cortex-M33 + RISC-V for efficient processing.
  • Ultra-Low-Power Design: Optimized dual-chip architecture for minimal power consumption.
  • High Reliability: Integrated TXCO ensures stable and accurate frequency performance, even in extreme temperatures.
  • Rich Interfaces: Supports USB, UART, I2C, and multiple GPIOs for flexible expansion.
  • Open Development Support: Fully open-source platform for secondary development and customization.
  • Multi-Protocol Support: LoRaWAN + BLE 6.0.
  • RF Options: SX1262 / LLCC68.
  • Compact Size: Designed for space-constrained IoT devices.
Diagram illustrating key features: Dual-Core Architecture, Ultra-Low-Power Design, High Reliability, Rich Interfaces, Open Development Support.

Figure 2: ME25LS03 Key Features

3.2. Applications

The ME25LS03 module is suitable for a variety of applications requiring long-range, low-power wireless communication:

  • Agricultural Automation
  • Asset Tracking
  • Inventory Management
  • Livestock Tracking
  • General IoT devices
Image showing the ME25LS03 module at the center, surrounded by icons representing its applications: Agricultural Automation, Asset Tracking, Inventory Management, and Livestock Tracking.

Figure 3: Typical Applications of ME25LS03

4. Setup and Installation

4.1. Pin Assignment

The ME25LS03 module provides a comprehensive set of pins for various functionalities. Below is the pin assignment diagram and table for reference.

Pin Assignment diagram for the ME25LS03 module, showing pin numbers and their corresponding functions.

Figure 4: ME25LS03 Pin Assignment Diagram

Symbol Type Definition Notes
VCCPositive power supplyPower supply, 1.7V-3.6VNormal 3.3V
GNSNegative power supplyGrounded
LR_ANTExternal antenna pinLoRa antenna RF pin
SWCLK/SWDIOI/O, Debug pinMultiplexed I/O and debug pins. During debugging, only these pins should be connected along with power and ground.
P0.02 - P0.04GPIOGeneral IO portP2.01: LoRa_SCK
P1.02 - P1.15GPIOP2.02: LoRa_MOSI
P2.01 - P2.02GPIOP2.04: LoRa_MISO
P2.04GPIOP1.00/32K_XL1
P2.06 - P2.10GPIOP1.01/32K_XL2
nRESETResetResetMCU reset pin

4.2. Mechanical Drawing

The physical dimensions of the ME25LS03 module are crucial for integration into your designs.

Mechanical drawing of the ME25LS03 module showing dimensions in millimeters, including length, width, and height.

Figure 5: ME25LS03 Mechanical Drawing (Unit: mm, Tolerance: ±0.15, default)

Image comparing the ME25LS03 module size (25mm x 15mm x 3.2mm) to two gold coins, illustrating its compact form factor.

Figure 6: Compact Size for Easier Integration (25 x 15 x 3.2mm)

4.3. Module Connection Diagram

This diagram illustrates the typical connections for the ME25LS03 module.

Module connection diagram showing BLE_RF, VCC, SWDIO, SWDCLK, GPIO pins, nRESET, and GND connections.

Figure 7: Module Connection Diagram

4.4. Power Supply

The operating voltage range of the chip is 1.8V to 3.6V. To ensure proper operation and stability, it is recommended to maintain the supply voltage at 3.3V.

4.5. SPI Interface Characteristics

The SPI interface operates using an external SCK clock, supporting speeds up to 16 MHz. Data transmission initiates when the NSS pin goes low. When NSS is high, the MISO line enters a high-impedance state. The module functions as an SPI Slave.

Symbol Description Minimum Typical Maximum Unit
t1NSS falling edge to SCK setup time32--ns
t2SCK period62.5--ns
t3SCK high-level time31.25--ns
t4MOSI to SCK hold time5--ns
t5MOSI to SCK setup time5--ns
t6NSS falling edge to MISO delay time0-15ns
t7SCK falling edge to MISO delay time0-15ns
t8SCK to NSS rising edge hold time31.25--ns
t9NSS high-level time125--ns
t10NSS falling edge to SCK setup time when switching from SLEEP to STDBY_RC mode100--S
t11NSS falling edge to MISO delay time when switching from SLEEP to STDBY_RC mode0-150S
SPI Active Timing diagram showing NSS, SCK, MOSI, and MISO signals over time.

Figure 8: SPI Active Timing

4.6. Module Internal TX, RX Mode Control

The module's internal TX/RX mode is controlled by the ANT_SW1 pin:

  • When ANT_SW2 detects a high level, the module operates in TX (transmit) mode.
  • When ANT_SW2 detects a low level, the module operates in RX (receive) mode.
MODE DIO2(ANT_SW1)
TX1
RX0

4.7. PCB Layout Guidelines

Proper PCB layout is critical for optimal module performance. Adhere to the following guidelines:

  • The module's antenna area should be completely clear of any metal obstructions.
  • Avoid placing GND planes or metal cross wiring in the antenna area.
  • It is recommended to create a hollow or clear area around the antenna, or place the module on the edge of the PCB board.
  • Maintain a solid copper pour outside the module's antenna area to minimize interference.
  • Ensure a clear area of at least 4mm around the module's antenna (including its casing) to reduce interference.
  • Provide good grounding for components to minimize parasitic inductance.
  • Do not place copper directly under the module's antenna to prevent interference with signal radiation.
  • Keep the antenna away from other circuits to maintain radiation efficiency.
  • Position the module as close to the edge of the circuit board as possible.
  • Consider using a ferrite bead for isolation when connecting the module to the power supply.

4.8. Reflow and Soldering Guidelines

Follow these guidelines for proper reflow soldering:

  • Perform SMT according to the reflow oven temperature profile provided in the datasheet, with a maximum temperature of 260°C.
  • Adhere to IPC/JEDEC standards; Peak temperature: <260°C.
  • Number of reflows: <2 times. For double-sided placement, the module side should undergo reflow soldering only once.
  • For module SMT, it is recommended to use a local step steel mesh with a thickness of 0.13-0.15mm and a pin length of 1-1.3mm.
  • If the entire package is not used at once after opening, store it in a vacuum to prevent moisture absorption and pad oxidation.
  • If there is a gap of 7 to 30 days before reuse, bake the tape at 65-70°C for 24 hours without unrolling it before returning to SMT.
  • Implement ESD protection measures before using SMT.
Reflow oven temperature profile diagram showing temperature over time, with peak temperature, ramp-up, and ramp-down rates.

Figure 9: Recommended Reflow Temperature Profile

5. Operating Instructions

The ME25LS03 module is designed for integration into custom applications. Detailed operation involves programming the nRF54L15 microcontroller and configuring the SX1262 LoRa transceiver. Refer to the official SDK and API documentation for specific programming instructions.

Key operational commands for controlling IRQs and DIOs include:

  • SetDioIrqParams: Configures IRQs and DIOs for each IRQ event.
  • GetIrqStatus: Retrieves the value of triggered IRQs.
  • ClearIrqStatus: Clears one or more IRQs.
  • SetDIO2AsRfSwitchCtrl: Configures DIO2 to control the RF switch.
  • SetDIO3AsTcxoCtrl: Configures DIO3 to control the TCXO.

For advanced usage and specific command details, please consult the comprehensive datasheet and programming guides available from MINEWSEMI.

6. Maintenance

6.1. Storage Conditions

  • Use this product within 6 months after signing the receipt.
  • Store without opening the package at an ambient temperature of 5-35°C and a humidity of 20-70%RH.
  • If left for more than 6 months after receipt, confirm usability before use.
  • Store in a non-corrosive gas environment (e.g., no Cl2, NH3, SO2, NOx).
  • Avoid excessive mechanical shocks that could damage packaging material.
  • This product is suitable for MSL2 (JEDEC standard J-STD-020).
  • After opening, store at ≤30°C/<60%RH. Use within 3-6 months.
  • If the indicator color in the package changes, the product should be baked before welding.
  • Baking is not required for one year if exposure is limited to <30°C and 60%RH.
  • If exposed to (≥168h @ 85°C/60%RH) conditions or stored for more than one year, recommended baking conditions are 120+5/-5°C for 8 hours, once.
  • Products must be baked individually on heat-resistant trays.

6.2. Handling Conditions

  • Be careful when handling or transporting products to prevent excessive stress or mechanical shock.
  • Handle with care to avoid cracks or damages to terminals. Such damage can alter product characteristics.
  • Do not touch products with bare hands to prevent poor solderability and static electrical charge damage.

7. Troubleshooting

If you encounter issues with the ME25LS03 module, consider the following general troubleshooting steps:

  • Power Supply: Verify that the module is receiving the correct voltage (3.3V recommended) and that the power supply is stable.
  • Connections: Double-check all pin connections (VCC, GND, SPI, GPIOs, antenna) for proper seating and continuity.
  • Antenna: Ensure the antenna is correctly connected and suitable for the operating frequency band.
  • Software/Firmware: Confirm that the firmware loaded onto the module is correct and compatible with your application. Review your code for any logical errors.
  • Environment: Check for potential sources of interference in the operating environment.
  • Datasheet Review: Consult the detailed datasheet for specific electrical characteristics and operational limits that might be relevant to your issue.

For persistent issues or advanced diagnostics, please contact MINEWSEMI technical support.

8. User Tips

Based on common inquiries, users often look for evaluation boards to get started quickly. If you are looking to evaluate the nRF54L15 and SX1262 combination, check the MINEWSEMI website or contact their sales team for available evaluation kits or development boards that integrate these chips.

9. Specifications

Parameter Value Notes
Chip ModelSX1262 + nRF54L15
Antenna2.4G:PCB, LoRa:ANT PIN2.4G: PCB antenna is used by default. If U.FL is needed, contact sales.
Flash1.5MB
RAM256KB
Operating Voltage1.7V-3.6VStandard power supply voltage 3.3V
Working Temperature-40°C ~ +85°CStorage temperature is -40°C ~ +125°C
Operating FrequencyLoRa: 150MHz-960MHz, BLE: 2.4GHzLoRa: optional other frequency bands, Default set is 868MHz/915MHz
Transmission PowerBLE: -40-+8dBm, LoRa: +15-+22dBmConfigurable
Current (RX)16.95mAMax receiving current
Current (TX)159mAMax transmission current
Module Dimensions25 x 15 x 3.2mm
Quantity of IO Port25GPIOs, I2C, I2S, PWM, UART etc.

10. Package Information

The ME25LS03 modules are supplied in tape and reel packaging. Detailed packaging information is provided below:

Packaging information diagram showing the direction of tape drawer, reel dimensions, tape dimensions, and carton sizes.

Figure 10: Packaging Information

Details Quantity Net Weight Gross Weight Dimension
Reel-ME25LS03700PCS1176g1330.5gW=44mm, T=0.35mm

Note: Weight tolerance: ±10 g (unless specified).

11. Warranty and Support

This manual and all its contents are owned by Shenzhen Minewsemi Co., Ltd. and are protected by Chinese laws and applicable international conventions related to copyright laws. The certified trademarks included in this product and related documents have been licensed for use by MinewSemi. The company reserves the right to change the content of this manual according to technological development without prior notification. Unauthorized modification or use of this manual's content is prohibited.

For further technical details and documentation, please refer to the following resources:

11.3. Contact Information

For technical support, sales inquiries, or customization requests, please contact MINEWSEMI:

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.