1. Introduction
This manual provides clear instructions for installing Heloxyo HEPA filter elements into your iRobot Roomba vacuum cleaner. Following these instructions will ensure proper sealing, optimal filtration performance, and safe operation of your device.

2. Safety Information
Warning:
- Always power off and unplug the vacuum cleaner before installation or maintenance.
- Do not operate the vacuum cleaner without the filter correctly installed.
- Do not modify or intentionally damage the filter.
3. Product Use Limitations
- For dry household use only.
- Do not expose the filter to liquids.
- Install only in the designated filter compartment of compatible iRobot Roomba models.
4. Compatible Models
These HEPA filters are compatible with a range of iRobot Roomba E, I, and J Series models. Please verify your specific model before installation.

Compatible with:
- iRobot Roomba E Series: E5, E6, E7, e5(5150), e6(6134, 6198)
- iRobot Roomba I Series: i1, i3, i4, i5, i6, i7, i8, i3+(3550), i4+(4552), i6+(6550), i7+(7550), i8+(8550)
- iRobot Roomba J Series: J5, J6, J8, J9, j7(7550)
- And all "Plus" versions of the listed models.
Important Note:
- These filters are NOT compatible with Roomba Combo j7/j7+ or Roomba Combo j9+/10 Max models.
- Some users have reported that the dimensions may not be exact for all i6 models, potentially affecting fit.
5. Product Features
The Heloxyo HEPA filters are designed for exceptional performance in capturing various debris and allergens.

Key features include:
- 99% Filtration: High-efficiency particulate air (HEPA) filtration captures fine dust, pet dander, and other allergens.
- Solid Frame: Ensures durability and a secure fit within the vacuum cleaner.
- HEPA Nonwoven Filter Material: Advanced material for superior air purification.
- No Washing Required: Designed for dry use and replacement, not washing.

6. Specifications
| Attribute | Value |
|---|---|
| Brand Name | Heloxyo |
| Type | Vacuum Cleaner Parts (Filters) |
| Material | PP, Non-woven fabrics |
| High-concerned chemical | None |
| Origin | Mainland China |
Approximate Dimensions (per filter):
- Length: 6.1 cm (2.4 inches)
- Width: 5 cm (1.96 inches)
- Height: 2 cm (0.79 inches)

7. Setup and Installation
Follow these steps to correctly install the HEPA filter in your iRobot Roomba vacuum cleaner:
- Power Off: Ensure the vacuum cleaner is powered off and unplugged from any charging station.
- Open Compartment: Locate and open the filter compartment on your Roomba. Refer to your Roomba's specific user manual for exact location if unsure.
- Remove Old Filter: If an old filter is present, carefully remove it. You may gently tap it to dislodge dust before discarding.
- Insert New Filter: Insert the new Heloxyo HEPA filter firmly into the housing.
- Ensure Seal: Make sure the filter makes full contact with the sealing edge of the compartment. The filter should sit flat with no gaps.
- Close Compartment: Close the filter compartment securely.

Correct Installation Check:
- The filter sits flat with no gaps.
- The sealing edge fully contacts the housing.
- Normal suction is observed after startup.
8. Operating Instructions
Once the new HEPA filter is installed, your iRobot Roomba is ready for operation. The filter will effectively capture dust, debris, and allergens during the cleaning cycle. For optimal performance, ensure regular cleaning of the dustbin and periodic replacement of the filter as recommended in the maintenance section.
9. Maintenance
- Regular Cleaning: After each cleaning cycle, empty the Roomba's dustbin. Gently tap the filter over a trash can to remove accumulated dust and debris.
- Filter Replacement: Replace the HEPA filter every 2-3 months, or more frequently if you have pets or experience heavy usage, to maintain optimal cleaning performance and air quality.
- Do Not Wash: These filters are made of non-woven fabric and are not designed to be washed with water. Washing can damage the filter material and reduce its effectiveness.
10. Troubleshooting
If you encounter issues after installing a new filter, consider the following common problems and solutions:
- Loose Filter: If the filter feels loose or does not sit flush, remove it and reinstall, ensuring it is firmly seated and the sealing edge makes full contact with the housing.
- Reduced Suction: Check the filter's orientation. Ensure it is inserted correctly according to your Roomba's design. Also, verify that the dustbin is empty and the vacuum's brushes are clear of debris.
- Air Leakage: This often indicates improper sealing. Re-check the filter alignment and ensure the compartment lid is fully closed and latched.
11. User Tips
- Always double-check the compatibility list before purchasing to ensure the filters fit your specific Roomba model.
- When installing, pay close attention to how the old filter was seated to replicate the correct orientation with the new filter.
- If you notice a decrease in cleaning performance or an increase in dust escaping the vacuum, it's likely time to replace the filter.
12. Warranty and Support
For any questions regarding product defects or performance issues, please contact the seller or manufacturer directly. Keep your purchase receipt for warranty claims.
A detailed user manual in PDF format is available for download: User manual (PDF)