ONWA KP-27

Contents

ONWA KP-27 Marine GPS Chart Plotter User Manual

Model: KP-27 Series

Brand: ONWA Marine Electronics

1. Introduction

ONWA Chartplotters are designed to be all-sealed and waterproof, capable of rapid position-fixing and resistant to harsh marine environments. The advanced processors ensure faster display performance, while the professional and user-friendly design simplifies operation. The built-in large-capacity map storage space provides intuitive and accurate navigation guidance.

This device is suitable for navigation and position-fixing of various vessels at sea and rivers, as well as for hydrographic information collection and river management.

Key Features:

  • Easy to operate interface.
  • Ultra-high brightness LCD, viewable under strong sunlight.
  • Compatible with multi-mapping systems: C-MAP, Navionics, KChart2.0, and KChart3.0.
  • High-resolution LCD display.
  • Built-in Class B+ AIS module (for KP-27A and KP-27X models only).
  • Selectable NMEA0183 output baud rate and sentences.
  • Free access to ONWA's detailed worldwide KChart system.
  • IPX6 waterproof rating.
  • Supports NMEA2000 (N2K) connectivity.
  • Compatible with optional external ONWA fishfinder module.

2. Safety Instructions

Please read these safety instructions carefully before operating or installing the equipment. Failure to follow these instructions may result in fire, electrical shock, serious injury, or equipment damage.

2.1 Safety Instructions for the Operator

  • Do not open the equipment: Only qualified personnel should work inside the equipment.
  • Do not disassemble or modify the equipment: Fire, electrical shock, or serious injury can result.
  • Immediately turn off the power at the switchboard: If the equipment is emitting smoke or fire, continued use can cause fire or electrical shock. Contact an ONWA agent for service.
  • Use the proper fuse: Use of a wrong fuse can damage the equipment or cause fire.
  • Be sure the power supply is compatible with the equipment: Incorrect power supply may cause the equipment to overheat.
  • Operating Temperature: The usable temperature range for the display unit is -5°C to 55°C. Using the equipment outside these ranges may damage it.

2.2 Safety Instructions for the Installer

  • Do not open the cover unless totally familiar with electrical circuits and service manual: Improper handling can result in electrical shock.
  • Turn off the power at the switchboard before beginning the installation: Fire or electrical shock can result if the power is left on.
  • Be sure that the power supply is compatible with the voltage rating of the equipment: Connection of an incorrect power supply can cause fire or equipment damage.
  • Use the proper fuse: Use of a wrong fuse can damage the equipment or cause fire.

3. Product Overview and Specifications

The ONWA KP-27 is a 7-inch GPS Chart Plotter designed for marine navigation. Below are its detailed specifications.

3.1 Plotter Characteristics

Feature Specification
Waypoints/Icons12000 user waypoints with name, symbol; 3 system waypoints (MOB, Start, Cursor); 10 proximity waypoints
RoutesMax 30 routes, up to 170 waypoints each
Tracks8000 points automatic track log; 10 saved tracks (up to 8000 track points each)
Drawing Marks1000
Drawing Lines2000
Drawing Placename1000
Color for drawing8
AlarmsXTE, Anchor drag, arrival, speed, voltage, proximity waypoint, timer and AIS (CPA and TCPA) alarm
PaletteNormal, Daylight exposed to sunlight, Night in dark environment, NOAA paper chart color
TidesBuilt-in worldwide tide data
Position formatLAT/LON
BasemapWorldwide
External MapCompatible K-Chart2.0, K-Chart3.0, C-MAP MAX and Navionics+
User data storageInternal backup of user settings or external SD card
Plot Intervals5sec to 60minutes or 0.01 to 10nm
Plotting scales0.001 to 700nm
Perspective ViewON/OFF (for C-Map only)
CelestialSunrise/Sunset Moonrise/Moonset

3.2 AIS Specifications

Feature Specification
Max number of AIS targets700 AIS targets display
AIS target tracking10 Manually saved tracks (300 points each)
AIS alarmCPA and TCPA

3.3 GNSS Receiver Specifications

Feature Specification
Receiver50 parallel channel GNSS receiver continuously tracks and uses up to 50 satellites
GNSS SupportGPS, Beidou and GLONASS (KP-25, KP-25F, KP-27, KP-27F); GPS and Beidou (KP-25A, KP-25X, KP-27A, KP-27X)
Acquisition timeCold start: 29 seconds; Hot start: 1 second
Update rate1 sec or 0.1 sec. selectable (KP-25, KP-25F, KP-27, KP-27F); 1 sec. (KP-25A, KP-25X, KP-27A, KP-27X)
AccuracyPosition: 3 meters (95%) without S/A; Velocity: 0.1 meter/sec. without S/A
DynamicsAltitude: 18,000 meters; Velocity: 515 meter/sec.
DatumWGS84, User define (KP-25, KP-25F, KP-27, KP-27F)
SBASSupported (For all models)
QZSSSupported (For all models)

3.4 Class B+ AIS Module (for KP-25A, KP-25X, KP-27A and KP-27X)

Feature Specification
Frequency156.026MHz ~ 162.025MHz
TechnologySOTDMA
Channel Bandwidth25KHz
ModulationGMSK
Data Rate9,600bps
No. of Transmitter1
No. of Receiver2
AIS Channel 1CH87B (161.975MHz)
AIS Channel 2CH88B (162.025 MHz)
TX Power Output5 Watt (37dBm +/-1.5dB)
RX Sensitivity<-107dBm @20%PER
RX Message FormatAIS Class A and B messages
Comply StandardIEC-62287 IEC-62287-2 Ed.2.0:2017

3.5 HD Fishfinder Characteristics (for KP-25F, KP-25X, KP-27F and KP-27X)

Feature Specification
Echo Color16 colors (including background color) according to echo intensity. Background color selectable from blue, white, and black.
Basic Range (Meters)5, 10, 20, 40, 80, 150, 200, 300, 600, 1000
Basic Range (Feet)15, 30, 60, 120, 200, 400, 600, 1000, 2000, 3000
Basic Range (Fathoms)3, 5, 10, 20, 40, 80, 100, 150, 300, 600
Range ShiftUp to 1000 meters (3000 feet, 600 fathoms)
Zoom RangeTimes 2, 3, 4, 6
Bottom Lock Expansion5/10 meters, 10/20 feet, 2/5 fathoms
Auto ModeAutomatic adjustment of range and gain
Display ModeHigh Frequency (200KHz), Low Frequency (50KHz), Dual (200K and 50K 1/2 display on each), Zoom (200KHz and 50KHz zoom) and A-scope Display
Zoom DisplayMarker Zoom, Bottom Zoom and Bottom-lock Expansion
Display Advance SpeedLines/TX: Freeze, 1/8, 1/4, 1/2, 1/1, 2/1, 4/1, 6/1, 8/1, 10/1
TX Frequency50 and 200kHz (alternately transmitted)
Power Output600W
Interference RejecterRejects unwanted signals by comparing last and present echoes in strength.
AlarmFish and Bottom alarms, Temperature alarm (sensor required)
Power Supply10.5VDC to 35VDC
Current drain at 12V< 1.0A

3.6 GPS Interface

Feature Specification
GPS DataRS232/RS422 input / output, NMEA0183 V3.01 and V4.11
GPS Input BaudrateAuto scan (4800, 9600, 19200 and 38400)
GPS Output BaudrateSelectable among 4800, 9600, 19200 and 38400

3.7 AIS Interface

Feature Specification
AIS DataRS232/RS422 output, VDO, VDM, GGA, GSA, GSV and RMC
AIS Input Baudrate38400 from GPS input port (For KP-25, KP-25F, KP-27 and KP-27F only)
AIS Output Baudrate38400 (For KP-25A, KP-25X, KP-27A and KP-27X only)

3.8 NMEA Sentence Supported

Input (auto scan baudrate): GGA, GLL, GSA, GSV, RMC, HDG, HDM, HDT, VTG, ZDA, MTW, VWR, VWT, MWD, VPW, VHW, TLL, TTM, VDO, VDM, GNS, MTA, RMA, DBT, DPT, MWV, BWC, XTE, ZDL, WPL, AAM, APB, BOD, RMB, DSC, MDA, RPM, XDR.

Output (selectable baudrate: 4800, 9600, 19200, 38400): GGA, GLL, RMC, GSA, GSV, AAM, APA, APB, BOD, BWC, BWR, DBT, DPT, HDT, MTW, RMB, TLL, VTG, WPL, XTE, ZDA, ZTG, ZDL, MWD, VPW, VWR, VWT.

Outputs for Autopilot: APA, APB, XTE, BOD.

3.9 NMEA2000 Supported PGNs

Description PGN Content
GNSS126992System Time
129026COG & SOG, Rapid Update
129540GNSS Satellites in View
129033Local Time Offset
129029GNSS Position Data
127250Vessel Heading
127258Magnetic Variation
129025Position, Rapid Update
129539GNSS DOPs
129291Set & Drift, Rapid Update
129044Datum
AIS129810AIS Class B "CS" Static Data Report, Part B
129809AIS Class B "CS" Static Data Report, Part A
129798AIS SAR Aircraft Position Report
129793AIS UTC and Date Report
129040AIS Class B Extended Position Report
129039AIS Class B Position Report
129038AIS Class A Position Report
129041AIS Aids to Navigation (AtoN) Report
129802AIS Safety Related Broadcast Message
129801AIS Addressed Safety Related Message
129794AIS Class A Static and Voyage Related Data
129795AIS Addressed Binary Message
129797AIS Binary Broadcast Message
Sounder128267Water Depth
Navigation127237Heading/Track Control
129284Navigation Data
129283Cross Track Error
127245Rudder
127251Rate of Turn
128259Speed, Water Referenced
128275Distance Log
Environment130306Wind Data
130310Environmental Parameters - DEPRECATED
130311Environmental Parameters - DEPRECATED
130312Temperature - DEPRECATED

3.10 Physical Dimensions and Weight

Model Size (H x W x D) Weight Display Waterproofing Temperature Range
KP-25 Series143.1(H)mm x 215.3(W)mm x 63.1(D)mm0.8 Kg (KP-25), 0.9 Kg (KP-25A/F), 1.0 Kg (KP-25X)5 inches Color TFT day-view LCD 800 x 480 pixelsDisplay unit: IPX6; GPS antenna: IPX6Display unit: -15°C to +55°C; GPS antenna: -25°C to +70°C
KP-27 Series155.1(H)mm x 241.3(W)mm x 62.9(D)mm0.9 Kg (KP-27), 1.1 Kg (KP-27A/F), 1.2 Kg (KP-27X)7 inches Color TFT day-view LCD 800 x 480 pixelsDisplay unit: IPX6; GPS antenna: IPX6Display unit: -15°C to +55°C; GPS antenna: -25°C to +70°C
Dimensions of KP-27 Series Chart Plotter
Figure 3.1: Dimensions of KP-27 Series Chart Plotter
Dimensions of KP-25 Series Chart Plotter
Figure 3.2: Dimensions of KP-25 Series Chart Plotter

4. Setup and Installation

4.1 Package Contents

Upon opening the box, please verify that all the following items are included:

  • Display unit (including installation bracket and ear clamp)
  • GPS patch antenna
  • Panel Cutout Pattern
  • Quick start and installation manual
  • Face mask and Panel Installation Sticker
  • Standard accessories pack (one 8-core Power/Data Cable, 2 spare fuses, 4 bracket mounting screws, 8 panel mounting screws)
ONWA KP-27 Chart Plotter and included accessories
Figure 4.1: KP-27 Chart Plotter and Standard Accessories

4.2 Optional Accessories

  • Heading/GPS sensor: KA-GC9A
  • Fishfinder transducer (For KP-25F, KP-25X, KP-27F and KP-27X):
    • NBM40-50/200T through hull transducer (Plastic, 600W dual frequency with temperature sensor)
    • NMM40-50/200T through hull transducer (Bronze, 600W dual frequency with temperature sensor)
    • KTD-520 transom mount transducer (Plastic, 600W dual frequency with temperature sensor)
  • Onwa NMEA2000 converter: KC-2W
  • Onwa ultrasonic weather station: KW-360 and KW-360_mini

4.3 Installing the Unit

There are three primary methods for installing the fixed equipment: desktop stand mounting, suspension mounting, and embedded panel mounting.

4.3.1 Desktop Stand Mounting

The unit should be mounted on a flat, solid surface for maximum stability. Ensure the mounting bracket is securely fixed with 5mm screws. Avoid installing the unit in areas prone to vibration, spray, rain, or direct sunlight. Maintain a space of more than 10cm between the rear of the unit and any wall for proper ventilation.

Desktop Stand Mounting Diagram
Figure 4.2: Desktop Stand Mounting

4.3.2 Suspension Mounting

  1. Secure the bracket to the chosen installation position using the provided four screws.
  2. Attach the chartplotter to the bracket using the provided two knobs.

Notice:

  • Ensure that the hanging position of the unit can bear the weight of the device and is installed securely and steadily.
  • Ensure that the unit is securely fastened to the bracket and thoroughly check to prevent any accidental dropping or injury.

4.3.3 Embedded Panel Mounting

  1. Open a hole on the panel according to the provided flush mount template and Panel Installation Sticker.
  2. Remove the 2 strips on the facial panel of KP-25 (or KP-27).
  3. Place the KP-25 (or KP-27) into the hole prepared in Step 1.
  4. Fix the unit by the 4 supplied screws.
  5. Place back the 2 strips that were removed in Step 2.

4.4 Interconnection Diagram

Refer to the diagram below for proper wiring and connection of the chart plotter with various accessories.

Interconnection Diagram for ONWA Chart Plotter
Figure 4.3: Interconnection Diagram

Power/Data Connections:

  • NMEA 0183 IN+ / IN- (GPS/AIS data from external equipment)
  • AIS OUT+ / OUT- (AIS data to external equipment - for KP-25A, KP-25X, KP-27A, KP-27X only)
  • NMEA 0183 OUT+ / OUT- (GPS data to external equipment)
  • Power+ / Power- (Battery connection)

NMEA2000 Connector:

  • 2+V, 3-V, 4 SIG H, 5 SIG L, 1 SHIELD

XDUCER (Transducer) Connections:

  • Sonar+, Temperature ground, No Connection, Temperature, Sonar-, Sonar ground
  • Transducer (Supplied as an option) - Only for KP-25F, KP-25X, KP-27F and KP-27X

5. Operation Overview

5.1 Keypad Instructions

The keypad provides intuitive control over the chart plotter's functions. Familiarize yourself with the button layout and their primary functions:

Button Function (Plotter) Function (Sounder)
▲ (Up Arrow)Move cursor upward / Change settingMove VRM upward
▼ (Down Arrow)Move cursor downward / Change settingMove VRM downward
◀ (Left Arrow)Move cursor to the leftLong press: Activate SHIFT range function; Short press: Activate echoes history marker
▶ (Right Arrow)Move cursor to the rightLong press: Activates feeding rate selection for picture advancement; Short press: Activate echoes history marker
MENUPress once: Displays menu of current page; Press twice: Enters main menu.
MODEDisplays 9 screen modes available for selection. Plotter: Press and hold to change track color. Sounder: Press and hold to activate sonar mode selection.
X (Cancel)Withdraw from optional operation, activate graphic mode selection. Confirms input or data. Plotter: Long press: Activates Drawing Mark option; Short press: Activates waypoint attribute edit window.
+/- (Zoom)Enlarges/Reduces scale of maps and chartsDecreases/Increases depth range for shallow/deeper waters
fx (Function)Displays other functions (GOTO, tide table, search, etc.) menu. Sounder: Provides signal level selection.
Power (On/Off)Long press: Turn power ON/OFF; Short press: Adjust screen brightness and keypad backlight dimmer.

5.2 Turning ON and OFF Power

  1. To turn on, press the Power key. The unit will beep and display the "ONWA" logo. Wait for the unit to fully boot up and display the warning page.
  2. Press the ✓ key to enter working mode.
  3. To turn off, press and hold the Power key until the screen goes off.

5.3 Brightness Adjustment and Day/Night Display Mode Settings

5.3.1 Brightness Adjustment

  1. Short press the Power key. The brightness adjusting window will appear.
  2. Use the ▲ or ▼ keys to adjust LCD display brightness.
  3. Use the ◀ or ▶ keys to adjust keypad backlight.
  4. Press the X key to confirm and exit.

5.3.2 Day / Night Display Mode Settings

When the brightness adjustment window is open, press the fx key to switch between day and night display modes.

Day and Night Display Modes
Figure 5.1: Day and Night Display Modes

5.4 How to Select Display Mode

  1. Press the MODE or X key in any display mode. An Icon selection window will appear.
  2. Use the arrow keys to choose a display mode and press ✓ to enter that display mode.

Note: If some display modes cannot be selected (the icon turns to grey color), please check the SETUP menu to ensure the display mode is not turned off.

Display Mode Selection Screen
Figure 5.2: Display Mode Selection

6. Plotter Display Overview

This section details the various functions and settings related to the plotter display.

6.1 Choosing the Zoom Display Range

You may press +/- to Zoom In and Zoom Out as desired on the PLOTTER display.

6.2 Moving the Cursor

Press the cursor pad (arrow keys) to move the cursor. The cursor moves in the direction of the pressed arrow. The cursor position (latitude and longitude) is displayed at the top left corner of the PLOTTER display when the cursor is on. The range and bearing from your ship to the cursor also appear.

To clear the cursor, press the X key. Cursor position data will disappear when the cursor is off.

6.3 Panning the PLOTTER Display

Using the cursor, pan left, right, up, or down on your desired area. Place the cursor at the edge of the screen to start panning. The display shifts in the direction opposite to cursor pad operation.

6.4 Centering Own Ship's Position

Press the X key for centering your ship's position.

6.5 Map Settings

  1. Press the MENU key in the PLOTTER screen.
  2. Choose Map and then press ✓ to select.
  3. Choose the layer "ON" or "OFF" as desired and then press ✓ to finish.

6.5.1 Palette

  1. Press the MENU key in the PLOTTER screen.
  2. Choose Palette and then press ✓ to select.
  3. Choose "Normal", "Daylight", "Night" or "NOAA" as desired and then press ✓ to finish.

6.5.2 Map Direction

  1. Press the MENU key in the PLOTTER screen.
  2. Choose Map Direction and then press ✓ to select.
  3. Choose "Normal", "North Up", "WPT Up", "COURSE Up" or "Head up" as desired and then press ✓ to finish.
  • Normal: Similar to North up, map does not move, only own boat position moves.
  • North up: North is always on the top of the display, own boat does not move, only the map moves.
  • WPT up: Only available in GOTO mode when a waypoint is set as destination. The waypoint is always on the top of the display.
  • Course up: COG (Course over ground) is always on the top of the display.
  • Head up: The heading of your own boat is always on the top of the display. Requires an external heading signal input.

7. Track Management

This section explains how to manage the track of your own boat.

7.1 Change the Color of Current Track

  1. Press and hold the MODE key on the Plotter screen until the track color box appears.
  2. Use the arrow keys to select the desired color (e.g., Red to Green) and press ✓ to confirm.

7.2 Change Plotting Intervals of Current Track

  1. Go to MAIN MENU > Track record > Track record mode.
  2. Choose from "Time", "Distance", "Auto", or "OFF" for the track record interval.
  • Time: Track is recorded and plotted at the set time interval.
  • Distance: Track is recorded and plotted at the set distance interval.
  • Auto: Plotting and recording interval changes with the plotter display range selected.
  • OFF: Track is neither recorded nor plotted.

7.3 Save Current Track

You can save the current track of your own boat for future use.

  1. Go to MAIN MENU > Track record > Save current track.
  2. You can change the color and name before saving.

7.4 Erase Current Track

You can delete the entire current track or specific segments by color.

  1. Go to MAIN MENU > Erase > Current track.

7.5 Erase Saved Track

You can erase saved tracks by colors or erase all saved tracks.

  1. Go to MAIN MENU > Erase > Saved track.

7.6 Transfer Saved Track to Route

You can transfer a saved track to a route for navigation purposes. You need to choose a starting point and an ending point of a saved track before transferring.

  1. Go to MAIN MENU > Track record > Transfer track to route.
  2. Choose a saved track from the list.
  3. Move the cursor to the starting point and press ✓.
  4. Move the cursor to the ending point and press ✓ again.
  5. Enter the name of the new route and press ✓ to confirm.
  6. After finishing the transfer, press X to quit the "Transfer saved track to route" function.

Note: After quitting, the cursor will turn from RED to BLACK color.

7.7 Display Saved Track on the Plotter Screen

  1. Press the MENU key in the PLOTTER screen.
  2. Choose Track and then press ▶ to select.
  3. Choose the color and whether to turn it "ON" or "OFF".
  4. Press ✓ to finish.

8. Waypoint and MOB (Man Overboard)

8.1 Entering Waypoints

Waypoints can be entered on the PLOTTER display in three ways: by cursor position, at your ship's position, and from the waypoint edit menu.

8.1.1 Entering a Waypoint with the Cursor

  1. Use the cursor pad to place the cursor on the desired location for a waypoint.
  2. Press the ✓ key. A window will appear.
  3. This window allows you to rename, edit LON and LAT, and choose mark shape and color.
  4. Choose "SAVE" to finish.

8.1.2 Entering a Waypoint at Own Ship's Position

  1. Momentarily press the ✓ key when no cursor is seen. A window will appear.
  2. If you do not need to change anything, choose "SAVE" to finish.

Note: If a cursor is visible on the plotter screen, press X to make it disappear before attempting this method.

8.1.3 Entering a Waypoint from the Waypoint List

  1. Press the MENU key twice (or three times from Plotter screen) to enter the main menu.
  2. Choose Edit and then press ▶ to select.
  3. Choose Waypoint and then press ✓. The waypoint list will appear.
  4. Choose NEW and then press ✓. A new window will appear.
  5. If you do not need to change anything, choose "SAVE" to finish.

8.2 Entering the MOB Mark

Only one MOB mark may be entered. Each time the MOB mark is entered, the previous MOB mark and its position data are overwritten.

  1. Long press the MOB key on any display mode. A confirmation window will appear.
  2. To set the MOB position as a destination, press ▶ to choose "YES" and then press ✓ key. Choosing "NO" saves the position as a waypoint called "MOB".

8.3 Operation on Waypoint Editing

Waypoint position, name, mark shape, and color can be edited from the Waypoint Edit menu.

  1. Press the MENU key twice (or three times from Plotter screen) to enter the main menu.
  2. Choose Edit and then press ▶ to select.
  3. Choose Waypoint and then press ✓. The waypoint list will appear.
  4. Choose the waypoint to edit and then press ✓. A new window will appear.
  5. Choose the object you want to edit and then press ✓ to select.
  6. Change the name, position, mark shape, or mark color as needed.
  7. Choose "SAVE" and then press ✓ to finish.

8.4 Erasing Waypoints

8.4.1 Erasing a Single Waypoint

  1. Follow steps 1-4 from "Operation on Waypoint Editing" to select the waypoint.
  2. Choose "ERASE" and then press ✓.
  3. Choose "YES" and then press ✓ to finish erasing that waypoint.

8.4.2 Erasing All Waypoints

  1. Press the MENU key twice (or three times from Plotter screen) to enter the main menu.
  2. Choose Erase and then press ▶ to select.
  3. Choose All waypoint/MOB and then press ✓. A confirming window will appear.
  4. Choose "YES" and then press ✓ to erase all waypoints.

9. Route Management

9.1 Creating Routes

  1. Press the MENU key two or three times to enter the main menu.
  2. Choose Edit and then press ▶ to select.
  3. Choose Route and then press ✓. The route list will appear.
  4. Choose NEW and then press ✓. A new window will appear.
  5. Use the ▲ or ▼ keys to enter the route name and then press ✓ to finish.
  6. Choose the location (e.g., 01) and then press ✓. A new window will open allowing you to choose a waypoint.
  7. Choose the waypoint name you want to include in the route and then press ✓. You can also create a new waypoint if needed.
  8. Repeat steps 6 and 7 until the route is complete.

9.2 Editing Routes

9.2.1 Replacing Waypoints in a Route

  1. Press the MENU key twice (or three times from Plotter screen) to enter the main menu.
  2. Choose Edit and then press ▶ to select.
  3. Choose Route and then press ✓ to select.
  4. Choose the route to edit and then press ✓.
  5. Place the cursor on the waypoint to replace, press the ✓ key to show the route options.
  6. Choose "Change" and then press ✓. The waypoint select window will appear.
  7. Choose the waypoint name you want to include in the route and then press ✓.
  8. Repeat steps 5 to 8 until the edit is complete.

9.2.2 Permanently Deleting a Waypoint from a Route

  1. Press the MENU key twice to enter the main menu.
  2. Choose Edit and then press the ▶ key to select.
  3. Choose Route and then press ✓ to select.
  4. Choose the route desired and then press ✓ to select.
  5. Choose the waypoint you want to delete and then press ✓ to show the route edit options.
  6. Choose "Remove" and then press ✓ to finish.

9.3 Erasing Routes

  1. Press the MENU key twice or three times to enter the main menu.
  2. Choose Erase and then press ▶ to select.
  3. Choose Route and then press the ✓ key. The route list will appear.
  4. Select a route and then press ✓ key.
  5. The confirm window will appear. Choose "ERASE" and then press ✓ key.
  6. Choose "YES" and then press ✓ key to finish.

9.3.1 Erase All Routes

  1. Press the MENU key twice or three times to enter the main menu.
  2. Choose Erase and then press ▶ to select.
  3. Choose All routes and then press ✓ key. The confirming window will appear.
  4. Choose "YES" and then press ✓ key to erase all routes.

10. Destination Management

10.1 Setting Destination by Cursor

  1. Press the fx key to display the FUNCTION window.
  2. Choose Goto cursor and then press ✓ to select.
  3. The cursor appears with "?". Use the cursor pad to place the cursor on the desired location for destination.
  4. Press the ✓ key to mark the destination.

10.2 Setting Destination by Waypoint (WPT)

  1. Press the fx key to display the FUNCTION window.
  2. Choose Goto WPT and then press ✓ to select. The WAYPOINT list will appear.
  3. Choose a waypoint and then press ✓ to finish.

10.3 Setting Route as Destination

  1. Press the fx key to display the FUNCTION window.
  2. Select Goto route and then press ✓ to select. The ROUTE list will appear.
  3. Choose a route and then press ✓. A new window will appear.
  4. Choose "Forward" or "Reverse" in order to traverse the waypoints in the route, and then press ✓ key to finish.

10.4 Setting Track Data as Destination

Track Data can be used for navigation.

  1. Press the fx key to display the FUNCTION window.
  2. Choose Goto track and then press the ✓ key to select. The SAVED TRACK window will appear.
  3. Choose the track you want to set as destination, and then press ✓ key.
  4. Choose "Forward" or "Reverse" to start Goto track navigation.

Once a Goto track has been activated, the track will divide it into segments. Up to 200 temporary waypoints are created (named T1, T2, T3, etc. and END) to mark the most significant features of the track, duplicating your exact path as closely as possible. To get the most out of the Goto track feature, remember the following tips:

  • Always clear the track log at the point that you want to go back to.
  • There must be at least two track log points stored in memory to create a track route.
  • If the receiver is turned off or satellite coverage is lost during your trip, it will draw a straight line between any point where coverage was lost and where it resumed.
  • If your track's changes in distance and direction are too complex, 200 waypoints may not mark your path accurately.

10.5 Canceling Destination

You can cancel a destination as follows:

  1. Press the fx key to display the FUNCTION window.
  2. Choose Stop goto and press ✓ key to finish.

10.6 Distance Measurement

Measure the distance of several points and save it as a route.

  1. Press the fx key in the PLOTTER screen to display the FUNCTION window.
  2. Select "Distance" and press ✓ key to activate the distance measurement function.
  3. Move the cursor to the starting point (A) and press ✓ to set up the starting point.
  4. Move the cursor to the next point (B). The BRG and LEG (bearing and distance from point A to point B) will display.
  5. Press ✓ key. Now DST (total distance) = distance from point A to point B is shown, while BRG and LEG turn to 0.
  6. Move the cursor to the next point (C). The BRG and LEG (bearing and distance from point B to point C) will display. DIST (total distance) displays the total distance from point A to point B.
  7. Press ✓ key. Now DIST = distance of point AB + distance of point BC is shown, while BRG and LEG turn to 0.
  8. Repeat steps 3, 4, and 5 to measure the distance of several points.
  9. To save or quit: Press X key during steps 3, 4, or 5. A menu will pop out with options to "SAVE" (save as a route), "QUIT" (quit without saving), or "CANCEL" (continue measurement).

11. Alarms

The chart plotter features six alarm conditions that generate both audio and visual alerts: Arrival alarm, Anchor drag alarm, XTE (Cross-Track Error) alarm, Speed alarm, Voltage alarm, and Timer alarm.

When an alarm condition is violated, the buzzer sounds, and the name of the offending alarm along with an alarm icon appears on the display. You can silence the buzzer and remove the alarm name indication by pressing any key. The alarm icon remains on the screen until the reason for the alarm is cleared.

11.1 Anchor Drag Alarm

The Anchor Drag Alarm informs you if your ship is moving when it should be at rest, or if it moves beyond a certain set range.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to display the ALARM menu.
  3. Choose Anchor and then press ✓ key. The alarm options will appear.
  4. Press ▶ key to select the alarm value and then press ✓ key to set the value.
  5. Choose "ON" and then press ✓ key to enable the alarm.

11.2 Arrival Alarm

The Arrival Alarm notifies you when your ship is approaching your set destination.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to display the ALARM menu.
  3. Choose Arrival and then press ✓ key. The alarm options will appear.
  4. Press ▶ key to select the alarm value and then press ✓ key to set the value.
  5. Choose "ON" and then press ✓ key to enable the alarm.

11.3 XTE (Cross-Track Error) Alarm

The XTE Alarm warns you when your ship deviates from its intended course.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to display the ALARM menu.
  3. Choose XTE and then press ✓ key. The alarm options will appear.
  4. Press ▶ key to select the alarm value and then press ✓ key to set the value.
  5. Choose "ON" and then press ✓ key to enable the alarm.

11.4 Speed Alarm

The Speed Alarm provides visual and aural alerts when your ship's speed is higher or lower than the set alarm range.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to display the ALARM menu.
  3. Choose Speed and then press ✓ key. The alarm options will appear.
  4. Press ▶ key to select the alarm value and then press ✓ key to set the value.
  5. Choose "ON" and then press ✓ key to enable the alarm.

11.5 Voltage Alarm

The Voltage Alarm warns you when the input voltage to the unit is higher than the set value.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to display the ALARM menu.
  3. Choose Voltage and then press ✓ key. The alarm options will appear.
  4. Press ▶ key to select the alarm value and then press ✓ key to set the value.
  5. Choose "ON" and then press ✓ key to enable the alarm.

11.6 Timer Alarm

The Timer Alarm provides audio and visual alerts when the set time has expired.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to display the ALARM menu.
  3. Choose Timer and then press ✓ key. The alarm options will appear.
  4. Press ▶ key to select the alarm value and then press ✓ key to set the value.
  5. Choose "ON" and then press ✓ key to enable the alarm.

11.7 Buzzer Type Selection

The buzzer sounds whenever an alarm setting is violated.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Alarm and then press ▶ key to select.
  3. Choose Buzzer and then press ▶ key to select.
  4. Choose the desired buzzer type ("Short", "Long", "Constant") and then press ✓ key to finish.
  • Short: Two short beeps
  • Long: Three long beeps
  • Constant: Continuous beeps

11.7.1 Disabling the Alarm

  1. Press any key to disable the buzzer of any alarm.
  2. The Alarm Icon will not disappear until the reason for the alarm is cleared.

12. Drawing Function

You can draw marks, lines, and place names on the plotter screen.

12.1 Drawing Marks

  1. Press the fx key and choose "DRAWING" on the function menu.
  2. Choose Mark. (Alternatively, press and hold X key on Plotter screen to enable drawing mark function.)
  3. A "?" symbol will appear beside the cursor, and the cursor will turn red.
  4. Move the cursor to the position where you want to place the mark, then press ✓. A "DRAWING MARK" window will appear.
  5. Choose the desired symbol and color for the drawing mark.
  6. Choose "SAVE" to save the drawing mark or "QUIT" to exit without saving.

12.2 Drawing Lines

  1. Press the fx key and choose "DRAWING" on the function menu.
  2. Choose Line.
  3. A "?" symbol will appear beside the cursor, and the cursor will turn red.
  4. Move the cursor to a starting point of the line, then press ✓.
  5. Move the cursor to the second point and press ✓ again. Continue to move the cursor and press ✓ to draw any shape you like.
  6. After you finish drawing lines, press X. A "DRAWING LINE" window will appear.
  7. Choose "SAVE" to save the drawing line or "QUIT" to exit without saving.

12.3 Drawing Place Names

  1. Press the fx key and choose "DRAWING" on the function menu.
  2. Choose Place name.
  3. A "?" symbol will appear beside the cursor, and the cursor will turn red.
  4. Move the cursor to the position where you want to put the place name, then press ✓. A "DRAWING PLACE NAME" window will appear.
  5. Move the cursor to the NAME field and press ✓. Start entering the place name using the direction arrow keys.
  6. After finishing entering the place name, press ✓ and choose "SAVE" to save or "QUIT" to exit without saving.

12.4 Erase or Edit Drawings

12.4.1 Erase or Edit Drawing Mark

  1. Move the cursor close to the mark you want to erase or edit. A pop-up text box "User Mark" will appear.
  2. Press ✓ to erase or edit the selected mark.
  3. After choosing "ERASE", you need to confirm.

12.4.2 Erase or Edit Drawing Line

  1. Move the cursor close to the lines you want to erase or edit. A pop-up text box of the line's name (e.g., "0000") will appear.
  2. Press ✓ to erase or edit the selected lines.
  3. Move the cursor to any point of the lines and press ✓ to change the location or erase this point from the lines.
  4. After choosing "ERASE", you need to confirm.

12.4.3 Erase or Edit Drawing Place Name

  1. Move the cursor close to the place name you want to edit or erase. A pop-up text box "Place Name" will appear.
  2. Press ✓ to erase or edit the selected place name.

13. Other Settings

13.1 Map Scale

You can change the map scale display format.

  1. Press the MENU key twice (or three times from Plotter screen) to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Map scale and then press ✓ to select.
  4. Choose "Nm" or "Ratio" as desired and then press ✓ to finish.

13.2 Unit of Measurement

Distance/speed can be displayed in nautical miles/knots, kilometers/kilometers per hour, or statute miles/kilometers per hour.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Speed unit and then press ✓ to select.
  4. Choose "nm, kt", "km, kmh" or "sm, kph" as desired and then press ✓ to finish.

13.2.1 Depth Unit

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Depth unit and then press ✓ to select.
  4. Choose "feet", "fathom" or "meter" as desired and then press ✓ to finish.

13.3 Bearing Reference (BRG. REF)

Ship's course and bearing to a waypoint may be displayed in true or magnetic bearing. Magnetic bearing is true bearing plus (or minus) earth's magnetic deviation. Use the bearing reference in accordance with the compass interfaced: magnetic for magnetic compass, true for gyrocompass.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose BRG. REF. and then press ✓ to select.
  4. Choose "True" or "Magnetic" as desired and then press ✓ to finish.

13.4 Magnetic Variation (MAG. VAR)

The location of the magnetic North Pole differs from the geographical North Pole, causing a difference between true and magnetic north direction. This difference is called magnetic variation and varies with respect to the observation point on earth. Your unit is pre-programmed with all the earth's magnetic variation. However, you may want to enter variation manually to refine accuracy. Set BRG. REF on the PLOTTER screen to "Magnetic" to use magnetic variation.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose MAG. VAR. and then press ✓ to select.
  4. Choose "Auto" or "Manual" (if you choose "Manual", you need to input the value manually) as desired and then press ✓ to finish.

13.5 Deviation

You can input the deviation of the ship or map manually to correct the position error from GPS error or map error.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Deviation and then press ✓ to select.
  4. Input the value as desired and then press ✓ to finish. To disable deviation, input "0" into the value.

13.6 Time

GPS uses UTC time. If you would rather use local time, enter the Time difference (range: -13:30 to +13:30) between it and UTC time. You may display the time in 12 or 24 hour format.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Time and then press ✓ to select.
  4. Input the time difference as desired. Choose "24H" or "12H" as desired and then press ✓ to finish.

13.7 TTG/ETA Speed

To calculate time-to-go and estimated time of arrival, enter your speed.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose TTG/ETA speed and then press ✓ to select.
  4. Choose "Auto" for automatic speed input (GPS calculated speed), or "Manual" for manual input.

13.8 Key Beep

You can set the key sound.

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Key beep and then press ✓ to select.
  4. Choose "OFF" or "ON" and then press ✓ to finish.

13.9 Wind Screen

  1. Press the MENU key twice to enter the main menu.
  2. Choose Setup and then press ▶ to select.
  3. Choose Wind screen and then press ✓ to select.
  4. Choose "ON" and then press ✓ to finish. The wind screen will become available.

14. GPS Settings

14.1 Choosing GPS Output Data

The unit's default is using an internal GPS module for position fixing. You can also use external GPS data for position fixing.

  1. Press the MENU key on the SATELLITE screen.
  2. Choose Output and then press ✓ to select.
  3. Choose "OFF", "NMEA0183" or "NMEA0183+AIS" as desired and then press ✓ key.
  4. Select any item in the red box area in the picture above and press the ✓ key to select the data you want to output.

14.2 Datum Setting

  1. Press the MENU key on the SATELLITE screen.
  2. Choose Datum and then press ✓ to select.
  3. Choose your desired datum and press ✓ key to confirm.

14.3 Smoothing

You can set up position smoothing, speed smoothing, and course smoothing.

  1. Press the MENU key on the SATELLITE screen.
  2. Choose POS smooth to enter position smoothing data.
  3. Choose SOG smooth to enter speed smoothing data.
  4. Choose COG smooth to enter course smoothing data.

Note: For slow vessels like fishing boats, the recommended smoothing settings are: POS smooth: 10, SOG smooth: 06, COG smooth: 10.

14.4 GNSS Settings

ONWA chartplotters use a GNSS module integrated with 3 global navigation systems: GPS, Beidou, and GLONASS.

For KP-25, KP-25F, KP-27, and KP-27F, these items can be changed. For KP-25A, KP-25X, KP-27A, and KP-27X, the GNSS module is inside the Class B+ AIS module, and the settings are programmed as default:

  • Datum: WGS-1984
  • SBAS: ON
  • GPS update rate: 1Hz
  • GNSS mode: GPS + Beidou

14.4.1 SBAS

SBAS uses GNSS measurements from reference stations to calculate and broadcast differential corrections and integrity messages. SBAS is turned on by default.

14.4.2 GPS Update Rate

When using the chartplotter on a speed boat, you might want to increase the update rate of your position. You can change the GPS update rate to 10Hz to increase the position update rate by 10 times.

14.4.3 GNSS Mode

You can choose different global navigation system combinations (default is GPS + Beidou):

  • One global navigation system: GPS only, Beidou only, or GLONASS only.
  • Two global navigation systems: GPS + Beidou, GPS + GLONASS, Beidou + GLONASS.

15. AIS Function

This chapter covers AIS functions for KP-25A, KP-25X, KP-27A, and KP-27X models, or when an AIS input is connected to KP-25, KP-25F, KP-27, and KP-27F.

15.1 Vessels List

  1. Press the MENU key on the AIS screen.
  2. Choose AIS detail list and then press ✓ key. The AIS SHIP LIST window will appear.

15.2 Collision Alarm

  1. Press the MENU key on the AIS screen.
  2. Select CPA Limit or TCPA Limit then press ✓ key to enter a value.
  3. Select CPA Alarm or TCPA Alarm then press ✓ key to choose "ON" or "OFF".

15.3 Own Ship's Information

There are two ways to display "Own Ship Info":

  1. Press the MENU key to select and enter the 'AIS detail list', then choose the first line in the list to check all the information about your own ship.
  2. Move the cursor to select your AIS Vessel on the chart screen and press the ✓ key.

15.4 Chart Screen

Users can check all AIS vessels being received in real-time on the chart screen, as well as the specific position and track of your own ship on the charts. The track length of AIS vessels depends on the equipment memory space, generally not less than 20 track points.

15.5 View AIS Vessels' Information on Plotter and AIS Screen

There are two ways to view AIS vessels' information: one is to move the cursor to select an AIS vessel on the Plotter screen and AIS screen, and press the ✓ key. The other is to select the AIS vessel from the AIS vessels list, and press the ✓ key.

15.6 Introduction to AIS Objects (AIS Screen)

The current location of your own ship is at the center of the map, appearing as a light blue hollow triangle. The vertex angle of the triangle stands for the current direction of your own ship. The blue hollow triangle stands for Class B vessels. The green hollow triangle stands for Class A vessels. A square icon stands for BASE STATION. A diamond icon stands for Aid_To_Navigation.

AIS CPA and TCPA Alarm Display
Figure 15.1: AIS CPA and TCPA Alarm Display
AIS Targets Overlay in Plotter Screen
Figure 15.2: AIS Targets Overlay in Plotter Screen

15.7 Emergency Alarm

Emergency alarm information is displayed at the bottom left corner. It cannot be deleted and is always available. If not read, the "emergency alarm" window will pop up later. The warning ship on the AIS and Plotter screen will be red and flashing. The relevant data will be saved for accident analysis.

15.8 Entry/Departure Setting

This setting temporarily shuts down or restarts the collision alarm. Useful when entering or leaving a port.

  1. Press the MENU key at the AIS screen.
  2. Choose Status then press ✓ to select.
  3. Select "In Port" or "Out Port" as desired and press ✓ to finish.

15.9 AIS Vessel Display

  1. You can define the AIS vessel display as either "Fill" or "Line".
  2. You can also select the size of the AIS Icon to either "Small", "Medium" or "Large".

15.10 AIS Track Display

You can enable or disable the display of AIS track on the plotter screen.

15.11 AIS Name

  1. You can turn on the name of AIS targets on the Plotter and AIS screen.
  2. You can also adjust the size of AIS target names.

15.12 Plotter AIS Display

You can choose to turn ON or OFF AIS targets display on the Plotter screen. You can also choose to display "NET" which is the Onwa AIS buoy on the Plotter screen.

15.13 AIS Track Recording

You can mark and save the track record of an AIS target. The maximum number of Manual AIS saved records is 10. If records are full, you need to delete some before saving new ones.

15.13.1 How to Do Manual AIS Track Recording

In the AIS target information box, there is a "Mark" function. When you press ✓, the AIS target is marked, and its track is recorded.

15.13.2 How to Transfer Saved AIS Track Record to a Route

You can transfer a saved AIS track record into a route. The operation is the same as "Transfer saved track to route" (Section 7.6).

16. Fishfinder Function

16.1 Sounder Mode

The sounder uses ultrasonic pulses to detect bottom conditions and fish schools.

  1. Press the MENU key in the SOUNDER screen.
  2. Choose Sonar mode and then press ✓ key (or press and hold MODE key) in the SOUNDER screen. The following window will appear.
Mode Function
200KHzProvides the high frequency (200KHz) normal picture on the full screen.
50KHzDisplays the low frequency (50KHz) normal picture on the full screen.
DUALDisplays the normal display for high frequency (200KHz) on the right half and low frequency (50KHz) on the left half.
200KHz ZOOMShows the normal display of the high frequency (200KHz) on the right half and its zoom display on the left half.
50KHz ZOOMProvides the normal display of the low frequency (50KHz) on the right half and its zoom display on the left half.
Different Display Modes for Fishfinder
Figure 16.1: Different Display Modes for Fishfinder
Built-in HD Fish Finder Display
Figure 16.2: Built-in HD Fish Finder Display

16.2 Gain Adjustment

  1. Press the MENU key in the SOUNDER screen.
  2. Choose Gain and then press ✓ key (or press and hold MODE key) to adjust gain manually.
  3. Choose "Manual", "Fishing" or "Cruising" as desired and then press ✓ key.

16.3 Range Adjustment

  1. Press the MENU key in the SOUNDER screen.
  2. Choose Range and then press ✓ to select.
  3. Choose "Manual" or "Auto" and then press the ✓ key.
  4. If "Manual" is chosen, press the X key to return to the SOUNDER screen, then use +/- to increase or decrease the depth range.

16.4 TVG (Time Varied Gain)

TVG compensates for propagation loss of sound, ensuring echoes from the same fish school size are displayed in the same color. It also helps reduce surface noise.

  1. Press the MENU key in the SOUNDER screen.
  2. Choose TVG and then press ✓ key.
  3. Choose "Off" or "Manual" as desired then press ✓ key.

16.5 Picture Advance

The picture advance speed determines how quickly the vertical scan lines run across the screen.

  1. Press the MENU key in the SOUNDER screen.
  2. Choose Pic. advance and then press ✓ key (or press and hold ▶ key).
  3. Use the ▲ or ▼ keys to select speed (e.g., 10/1 (FAST), 1/8 (SLOW), or STOP) and press ✓ key to finish.

16.6 Split Ratio

  1. When in PLOTTER+SOUNDER screen and the SOUNDER screen is >50%, press MENU key.
  2. Choose Split ratio and then press ✓ key (or press and hold MODE key) in the PLOTTER+SOUNDER screen.

16.7 Sonar Menu

  1. Press the MENU key in the SOUNDER screen.
  2. Choose Sonar menu and then press ✓ key.

16.7.1 A-Scope

This display shows echoes at each transmission with amplitudes and tone proportional to their intensities, on the right 1/4 of the screen. It is useful for estimating the kind of fish school and bottom composition.

  1. From the Sonar Menu, choose A-Scope and then press ✓ key.
  2. Press the ▲ or ▼ key to enable or disable the A-Scope.

16.7.2 Zoom Modes

From the Sonar Menu, choose Zoom mode and then press ✓ key. Choose "Marker Zoom", "Bottom lock" or "Bottom zoom" as desired then press ✓ key to finish.

Fishfinder Zoom Modes
Figure 16.3: Fishfinder Zoom Modes (Marker, Bottom Lock, Bottom Zoom)

16.7.3 Noise Limiter

Light-blue dots may appear over most of the screen due to unclean water or noise. This can be suppressed by adjusting Clutter on the menu.

  1. From the Sonar Menu, choose Noise limiter and then press ✓ key.
  2. Choose "Off", "Low", "Medium" or "High" as desired and then press ✓ key to finish.

16.7.4 Hue Selection

You can select the background and echo colors.

  1. From the Sonar Menu, choose Hue Selection and then press ✓ key.
  2. Use the ▲ or ▼ key to select the background and press ✓ key to finish.

16.7.5 Signal Level

  1. From the Sonar Menu, choose Signal level and then press ✓ key.
  2. Use the ▲ or ▼ key to select the signal level and press ✓ key to finish.

16.7.6 Marker

The white marker functions to display a particular echo color in white. For example, you may want to display the bottom echo (reddish-brown) in white to discriminate fish echoes near the bottom.

  1. From the Sonar Menu, choose Marker and then press ✓ key.
  2. Choose "VRM" or "WHT" as desired and then press ✓ key to finish.

16.8 Fishfinder Alarm

In the fish finder display, after entering the alarm information menu, you can see the options for "From" and "Span".

  • From: Indicates the depth at which the alarm starts detecting.
  • Span: Refers to the depth range extending downward from the starting depth.
  1. Press the MENU key in the SOUNDER screen.
  2. Choose ALARM and then press ✓ key.
  3. Press ▲ or ▼ key to select an alarm (Bottom, Fish, Temperature).
  4. Press ✓ key to select "OFF", "ON", "IN" or "OUT".
  5. Choose From then press ✓ key to adjust the alarm starting depth.
  6. Choose Span then press ✓ key to adjust the alarm range.

16.9 Data Field

The Data Field will appear on the right side of the screen. The black area is the data area which may be changed.

  1. Press the MENU key in the SOUNDER screen.
  2. Choose Data field and then press ✓ key.
  3. Press the ◀ or ▶ key to select the one you want to display on the data field, then press ✓ to finish.
  4. You can also choose to "Show/hide data field" as desired.

16.10 Saving History Echo to Waypoint Memory

You might want to save a fishing ground or a wreck location into waypoint memory.

  1. When you want to save the location of a history echo, slightly press the ▶ arrow key. A position vertical line will appear.
  2. After the position line appears, use the ◀ and ▶ arrow keys to move the position line to the desired location.
  3. Once the position line reaches the desired location, press ✓ key. A message box will pop up. You can save it into waypoint memory after editing the options.
  4. When you finish, press X to quit this function.

17. N2K Function

17.1 Overview of Functions

The N2K functionality enables the device to connect to the N2K network, facilitating bidirectional data sharing. The device can function as an N2K transmitter, sharing data with the network, or as an N2K receiver, accepting data shared by other devices.

17.2 Connecting to the N2K Network

17.2.1 Description of N2K Network Environment

A basic N2K network requires at least one data sharing end and one data receiving end. The following materials are needed at least:

  • 2 pcs. x terminating resistors
  • 2 pcs. x extension cables
  • 3 pcs. x T-connectors
  • 1 pcs. x power cord

17.2.2 Cable Connection

N2K Cable Connection Diagram
Figure 17.1: N2K Cable Connection

17.3 Data Sharing

The settings for N2K data sharing and reception need to be configured by navigating to the satellite screen and pressing the MENU key.

17.3.1 Data Sharing Settings

There are a total of 6 data types: GPS, Heading, Depth, Wind, Env (Environment), and AIS. You can individually configure whether to share each type of data.

17.3.2 Data Reception Settings

You can configure the reception of five types of N2K data: GPS, Heading, Depth, Wind, and AIS.

  • For AIS, you can only set whether to receive data from N2K sources by setting "N2K AIS IN" to "ON" in the "SATELLITE MENU".
  • For GPS, Heading, Depth, and Wind, you can configure by setting a data source priority and specifying a particular device as the source of corresponding data. (SATELLITE MENU > Prefer data source > GPS (or Heading/Depth/Wind) > N2K).

17.3.3 Overview of Received N2K Data in the Network

In any screen, press the MENU key (3 times for chart screen, 2 times for other screens) to bring up the 'MAIN MENU'. Choose the 'Setup' menu, then select 'NMEA2000 Network Analyze' and open it with the ✓ key. Here, you can view all the N2K data currently received by this device. Use the ▲ and ▼ keys to navigate and inspect the details of each specific data entry.

Explanation of N2K Device List Colors:

  • Black font: The device is currently sharing the corresponding data.
  • Red font: The device has been selected as the N2K source for corresponding data on your device.
  • Gray font: The device is currently in the N2K network but does not output or share corresponding data, and it is not selectable.

If the N2K device list is empty, it means there are no other devices in the current N2K network or your device is not in the N2K network.

18. Data Management

18.1 How to Connect Output Data to External Equipment

18.1.1 Output Navigation Data

The chart plotter can output NMEA0183 sentences to external equipment. The output baud rate can be selected from 4800, 9600, 19200, and 38400.

Wiring Output: Connect pin5+ (Green) and pin6- (BROWN) to the input of the external equipment (RS232).

Select Output Sentences: First, turn on the output in the Satellite menu. Then, scroll the cursor to one of "AAM" below to select the desired output NMEA 0183 sentences. (Default output sentences: GGA, GLL, and RMC).

18.1.2 Output AIS Data (For KP-25A, KP-25X, KP-27A and KP-27X)

The chart plotter can output AIS data to external equipment. The default NMEA0183 sentences output from the AIS OUT port are: GGA, GSA, GSV, RMC, VDM, VDO. The baud rate from AIS OUT port is 38400.

Wiring Output: Connect pin4+ (Orange) and pin3- (Blue) to the input of the external equipment (RS232).

18.2 How to Connect NMEA0183 Sentences from External Equipment

18.2.1 Input Navigation Data

The chart plotter can accept NMEA0183 sentences from external equipment. The input baud rate is auto-scanned, so no setting is required. Supported auto scan baud rates: 4800, 9600, 19200, 38400.

Wiring Input: Connect pin1+ (Yellow) and pin2- (White) to the output of the external equipment (RS232).

18.3 Connecting a Temperature Probe

An Onwa 10K (10K resistance at 20°C or 68°F) temperature probe or Airmar temperature sensor can be connected to the chartplotter to display temperature on the sounder screen and data box.

18.3.1 Wiring of Temperature Probe (For KP-25F, KP-25X, KP-27F and KP-27X)

Connect a temperature probe to pin 2 and pin 4 of the XDUCER port.

18.3.2 Selection of Temperature Probe

To select the correct temperature probe after installation, access MAIN MENU > SETUP > Calibrate > Temperature curve.

18.3.3 Calibrate Temperature Accuracy

To adjust temperature accuracy or apply a temperature filter, access MAIN MENU > SETUP > Calibrate > Temperature curve.

18.4 Import and Export User Data

All user data (waypoint, route, track, drawing mark, drawing line, and drawing place names) can be imported or exported from the Onwa chartplotter through an SD card. The format for import and export is called Onwa Data Format (ODF).

18.4.1 Basic Mode

In basic mode, you can import one type of user data (e.g., waypoint) or combine all user data into one file using the merging function of Onwa KDX PC software. For export, all user data will be merged into one ODF file. You can convert ODF to GPX format (Google Earth format) using KDX PC software.

Import Data: Insert an SD card containing user data in ODF format. In any screen, press MENU x 2 > MAIN MENU > Data > Data In. Follow the on-screen prompts.

Export Data: Insert an SD card. In any screen, press MENU x 2 > MAIN MENU > Data > Data Out. Follow the on-screen prompts.

18.4.2 Advance Mode

In advance mode, you can add conditions on export user data, providing selection of user data types and range of data creation date.

18.5 Record and Playback

You can use the "Record data to SD" function to record all navigational data (position, SOG, COG, AIS data, and depth data) over a voyage or a certain period. The "Playback data from SD" function allows you to playback the recorded navigational data at any time.

19. User Tips

  • Screen Visibility: For optimal viewing in bright sunlight, ensure the brightness is adjusted to 'Daylight' mode.
  • Data Backup: Regularly back up your waypoints, routes, and tracks to an SD card to prevent data loss.
  • NMEA2000 Connectivity: When connecting to an NMEA2000 network, verify the device list colors (black for sharing, red for selected source, gray for not sharing) to ensure proper data flow.
  • Fishfinder Performance: For detailed fish finding, utilize the 200KHz frequency. For general detection and bottom conditions, 50KHz is more suitable.
  • AIS Target Tracking: Manually save important AIS tracks for later review, especially for incident analysis.

20. Troubleshooting / FAQ

This section provides solutions to common issues and answers frequently asked questions.

Q: The display is too dim in sunlight.

A: Adjust the screen brightness to 'Daylight' mode via the Power button's short press menu or the Palette setting in the Plotter menu.

Q: My AIS targets are not showing up.

A: Ensure the AIS module is enabled and correctly wired. Check the AIS settings under the AIS Function menu, particularly 'AIS track display' and 'Plotter AIS display'. Also, verify the NMEA0183 or NMEA2000 input settings for AIS data.

Q: The fishfinder is not showing clear echoes.

A: Check the transducer connection. Adjust the 'Gain' and 'Range' settings in the Fishfinder menu. If there's a lot of noise, try adjusting the 'Noise limiter' or 'TVG' settings.

Q: I cannot save new waypoints.

A: Check the available memory for waypoints. If the memory is full, you may need to erase old waypoints or transfer them to an SD card.

Q: The unit is not receiving GPS signal.

A: Ensure the GPS patch antenna is correctly connected and has a clear view of the sky. Check the GNSS settings under GPS Settings to ensure the correct GNSS mode is selected and SBAS is enabled if available in your region.

21. Abbreviations

Abbreviation Word
ESCEscape
ENTEnter
SBASSatellite-based augmentation system
POSPosition
SOGSpeed Over Ground
COGCourse Over Ground
AWSApparent Wind Speed
AWAApparent Wind Angle
TWSTrue Wind Speed
TWATrue Wind Angle
TWDTrue Wind Direction
VMGVelocity Made Good
INFOInformation
LATLatitude
LONLongitude
TTGTotal Time to Go
ETAEstimate Time of Arrival
XTECross Track Error
HDOPHorizontal Dilution of Precision
TVGTime Variable Gain
PICPicture
B/LBottom Lock
F/AFish Alarm
MAG.VAR.Magnetic Variation
ACA(AIS) Regional Assignment Channel Assignment Message
ACKAcknowledgement
ACS(AIS) Channel management information source messages
AFSKAuto frequency-shift keying
ALR(AIS) Alarm Message
A to NAid to Navigation
AISAutomatic Identification System
BIITBuilt In Integrity Testing
BNCBayonet fitting type Therefore connector
CRCarriage Return
CSCarrier Sense
CSTDMACarrier Sense Time Division Multiple Access
DCDirect Current
DGNSSDifferential Global Navigation Satellite System
DSCDigital Selective Calling
GLONASSGlobal Navigation Satellite System
GNSSGlobal Navigation Satellite System
GMSKGaussian Minimum Shift Keying
GPSGlobal Positioning Satellite / System
HFHigh Frequency
IMOInternational Maritime Organization
IECInternational Electro technical Commission
LEDLight Emitting Diode
LFLine Feed
LNALow-noise Amplifier
MFMedium Frequency
MKDMinimum Keypad and Display
MMSIMaritime Mobile Service Identity
MPEMaximum Permissible Exposure
NMEANational Marine Electronics Association
PCPersonal Computer
PIPresentation Interface
RFRadio Frequency
RTCMRadio Technical Commission for Maritime Services Commission
RXReceive or Receiver
RFIRadio Frequency Interference
SARSpecific Absorption Rate
SELVSeparated Extra Low Voltage
SMSShort Message System
SRMSafety Related Message
TDMATime-division Multiple Access
TNCThreaded type RF connector
TXTransmit or Transmitter
UTCUniversal Time Co-ordinated
VDM(AIS)VHF Data Link Messages
VDO(AIS)VHF data link own vessel messages
VHFVery High Frequency
VSWRVoltage Standing Wave Ratio

22. Glossary

This section provides definitions for technical terms used throughout this manual.

Term Definition
ChartplotterAn electronic device used in marine navigation that integrates GPS data with an electronic navigational chart (ENC) to display the vessel's position and track.
GPSGlobal Positioning System, a satellite-based navigation system providing location and time information.
SBASSatellite-Based Augmentation System, which enhances the accuracy and reliability of GPS.
AISAutomatic Identification System, a tracking system used on ships and by vessel traffic services (VTS) for identifying and locating vessels.
NMEA0183A standard for communication between marine electronic devices.
NMEA2000 (N2K)A newer, higher-speed communication standard for marine electronic devices, based on CAN bus.
WaypointA set of coordinates that identifies a point in physical space.
RouteA sequence of waypoints that defines a planned path for a vessel.
TrackA record of the actual path traveled by a vessel.
MOBMan Overboard, a function to quickly mark and navigate to the location where a person fell overboard.
FishfinderA sonar device used to locate fish underwater by detecting reflected sound pulses.
TransducerA device that converts electrical energy into sound waves and vice versa, used in fishfinders and depth sounders.
CPAClosest Point of Approach, the minimum distance between two vessels.
TCPATime to Closest Point of Approach, the time until two vessels reach their CPA.
XTECross-Track Error, the distance a vessel is off its intended course.
IPX6An IP Code rating indicating protection against powerful water jets.

23. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact your authorized ONWA dealer. Keep your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.