IKSLED Sweep Sensor 3410

Contents

IKSLED Sweep Sensor Switch Module User Manual

Model: Sweep Sensor 3410

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your IKSLED Short Distance Scan Sensor Sweep Hand Sensor Switch Module. This versatile module is designed for smart home applications, compatible with various LED lighting setups, and offers both hand sweep and door control functionalities with dimming capabilities.

Safety Information

  • Ensure the power supply is disconnected before installation or maintenance.
  • Do not exceed the maximum voltage (24V DC) or current (3A) ratings to prevent damage to the module or connected devices.
  • Avoid installing the sensor in direct sunlight or near strong heat sources, as this may affect performance.
  • Keep the sensor probe clear of obstructions during operation.
  • This device is not a smart device and does not connect to Wi-Fi or other smart home platforms directly.

Product Overview

The IKSLED Sweep Sensor Switch Module offers two primary modes of operation:

  • Type A (Hand Sweep Sensor): Allows for touchless control of lighting by waving a hand within the sensing range. Includes brightness adjustment and memory function.
  • Type B (Door Control Switch): Automatically turns lights on when a door opens and off when it closes.
Diagram showing Type A and Type B sensor functions
Figure 1: Functional overview of Type A (Hand Sweep) and Type B (Door Control) sensor modes.
Hand sweeping over a sensor to control an LED strip
Figure 2: A simple scan turns the light on or off. Sensing distance is 3-8cm.

Setup and Installation

Wiring Specifications

The module requires a low voltage constant voltage power adapter. Ensure the input voltage to the module is DC 3.7V-24V.

Wiring diagram for the sensor module
Figure 3: Wiring Diagram. Connect the power adapter (AC85-265V input, DC3.7-24V output) to the sensor module (V+ and V-), then connect the LED lamp to the sensor module (LED+ and LED-).

Installation Steps

  1. Ensure all power is disconnected before beginning installation.
  2. Connect the power adapter output (DC 3.7V-24V) to the V+ and V- terminals of the sensor module.
  3. Connect your LED lamp to the LED+ and LED- terminals of the sensor module.
  4. Mount the sensor module in the desired location. For hand sweep functionality, ensure the sensor probe is accessible and unobstructed. For door control, position the sensor so that the door's movement can block/unblock the sensor.
  5. Important: Do not block the sensor probe during installation. The module features a blue indicator light.
Installation demonstration showing sensor placement and indicator light
Figure 4: Installation demonstration. Note the blue indicator light and the instruction to not block the sensor probe.

Module Dimensions

Diagram showing dimensions of Type A and Type B sensor heads
Figure 5: Switch size. The functions of the two switches are the same, only the sensing heads are different. PCB dimensions are approximately 30mm x 10mm x 1mm. Type A sensor head: 4.5mm x 9mm x H6mm. Type B sensor head: Φ7.8mm x H6mm.

Operating Instructions

Type A: Hand Sweep Sensor Function

  • Turn On/Off: Wave your hand once within 3-8cm of the sensor to turn the light on. Wave your hand again to turn the light off.
  • Adjust Brightness (Dimming): With the light on, hold your hand steadily near the sensor (within 3-8cm) to adjust the brightness. The brightness will cycle through its range. Remove your hand when the desired brightness is reached. The module includes a brightness memory function, retaining the last set brightness level.
Video 1: Demonstration of Hand Sweep Sensor (Type A) operation, including turning on/off and dimming.

Type B: Door Control Switch Function

  • Automatic On/Off: When the sensor is installed in a door control configuration, the light will automatically turn on when the door opens (unblocking the sensor) and turn off when the door closes (blocking the sensor).

Maintenance

  • Cleaning: Gently wipe the sensor surface with a soft, dry cloth to remove dust or debris. Do not use abrasive cleaners or liquids directly on the sensor.
  • Environmental Conditions: Ensure the operating environment is within specified temperature and humidity ranges. Avoid excessive moisture or extreme temperatures.
  • Connection Checks: Periodically inspect wiring connections to ensure they are secure and free from corrosion.

Troubleshooting

Problem Possible Cause Solution
Light does not turn on/off.
  • No power to the module.
  • Incorrect wiring.
  • Sensor probe obstructed or dirty.
  • Sensing distance too far.
  • Check power supply connection and ensure it's active.
  • Verify wiring according to the diagram (Figure 3).
  • Clean the sensor probe and ensure no objects are blocking it.
  • Ensure hand/object is within 3-8cm of the sensor.
Dimming function not working (Type A).
  • Hand not held steadily over the sensor.
  • Sensor malfunction.
  • Hold your hand steadily over the sensor for a few seconds to activate dimming.
  • If the issue persists, contact support.
Light flickers or behaves erratically.
  • Unstable power supply.
  • Electrical interference.
  • Loose connections.
  • Ensure a stable power supply.
  • Relocate the module away from sources of strong electromagnetic interference.
  • Check all wiring connections for tightness.

Specifications

Feature Detail
Brand Name IKSLED
Model Number Sweep Sensor 3410
Switch Type Sensor Switch
Material Plastic
Voltage 3.7V, 5V, 12V, 24V DC
Electric Current Max. 3A
Load Power Max. 60W
Sensing Distance 3-8 cm
Is Smart Device No
Origin Mainland China
Certification RoHS, EMC, CE, CCC
Warranty 1 Year
Package Weight 0.035 kg
Package Dimensions 18cm x 14cm x 3cm

User Tips

  • For optimal performance, ensure the sensor is installed in a location where it won't be accidentally triggered by passing objects or reflections.
  • When using the dimming function, a slow, steady hold of the hand over the sensor provides the best control.
  • Consider the ambient lighting conditions; very bright environments might affect sensor sensitivity.
  • If installing in a cabinet or enclosed space, ensure adequate ventilation for the LED lights to prevent overheating.

Warranty and Support

This IKSLED Sweep Sensor Switch Module comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer directly.

Please retain your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.