einkshop 62xl

Contents

einkshop 62/62xl Ink Cartridge User Manual

Model: 62xl

Introduction

This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your einkshop 62/62xl replacement ink cartridges. These cartridges are designed to be compatible with various HP Envy and HP OfficeJet printer models, ensuring high-quality prints.

einkshop 62xl Ink Cartridges and Refill Tools

Image: A view of the einkshop 62xl black and tri-color ink cartridges, along with a refill syringe, clip, and small bottles of ink, indicating multiple purchase options and refill capability.

Setup and Installation

Before installation, ensure your printer model is listed as compatible. Refer to the image below for applicable models.

List of Compatible HP Printer Models

Image: A list of compatible HP Envy and OfficeJet printer models for the 62/62xl ink cartridges.

Cartridge Installation Steps

Always check that the new ink cartridges are the same model as your previous ones for normal operation.

  1. Prepare Printer: Open the front cover of your printer. Ensure the printer is turned on and the cartridge tray moves to the middle.
  2. Remove Old Cartridge: Press down on the old cartridge and carefully take it out of its slot.
  3. Unpack New Cartridge: Remove the new ink cartridge from its packaging.
  4. Remove Protection: Carefully remove the protective cover and the protection tape from the nozzle of the new cartridge. Avoid touching the nozzle or electrical contacts.
  5. Install New Cartridge: Insert the ink cartridge into its corresponding slot (black or color). Push it in firmly until it clicks into place completely.
  6. Close Cover: Close the front cover of the printer.
Ink Cartridge Installation Steps Diagram

Image: A six-step visual guide demonstrating how to install the ink cartridges into a printer, from opening the cover to closing it.

Important Precautions

  • Most printers require at least one black ink cartridge to be installed for normal printing.
  • Once an ink cartridge is unpacked, it should be used as soon as possible.
  • It is recommended to use the printer at least twice a week to prevent long-term idle nozzles from becoming blocked and unrecognized.

Ink Cartridge Protection Setting

Some printers have a "cartridge protection" setting. If enabled, a newly installed cartridge might be protected and only usable in that specific printer. Before installing, it is recommended to disable this setting in your printer's software or settings to allow the cartridge to be used in other compatible printers if needed.

Operation

First Use and Prompts

When using compatible cartridges, your printer or computer software may display messages such as "low ink," "insufficient ink," "used ink," or "imitation ink cartridges." These prompts are part of the printer manufacturer's protection for original consumables and do not affect the printing quality or functionality of your einkshop cartridges. Simply click "Continue" or "OK" to proceed with printing.

Ink Level Display

The ink level displayed on your computer will initially reflect the ink level of the cartridge. After the first print cycle, the ink cartridge may no longer display the ink level accurately, but it will still be recognized by the printer and function normally.

Maintenance

Ink Refill Guide (for refillable cartridges)

While einkshop cartridges are pre-filled and ready to use, they are designed to be refillable. Follow these guidelines if you choose to refill:

  1. Prepare for Refill: Carefully take out the ink cartridge from the printer.
  2. Inject Ink: Using a syringe, slowly inject the recommended volume of ink into the cartridge.
    • Recommended Volume: Black: 3-5ML; Color: 2-3ML.
    • Needle Insertion: Insert the needle only about 1CM into the ink cartridge to avoid damaging internal structures.
  3. Timing: Do not wait for the ink to be completely used up before refilling, as this can damage the ink cartridge port.
  4. Injection Speed: Inject ink slowly. Stop immediately when ink begins to emerge from the sponge.

Using the Ink Absorber (if included)

The ink absorber tool can be used for two main purposes:

  • Unblocking Nozzles: To clear blockages in the cartridge nozzles or resolve "no ink" situations.
  • Extracting Air: To remove air from the ink cartridges and pipelines, ensuring smooth ink flow.

How to Use:

  1. Place the green silicone piece into the ink absorber tool.
  2. Insert the ink cartridge into the ink absorber and snap it securely into place.
  3. Insert a syringe (without a needle) from the bottom of the absorber and draw out approximately 2ML of ink. (Use the long section for black cartridges, short section for color cartridges).

Note:

  • It may require a little force to properly seat the ink cartridge into the absorber.
  • If the ink cartridge is blocked or ink flow is uneven, using the ink suction clip to draw out ink can help.

Troubleshooting

Issue 1: Printer Prompts "Used Original Ink Cartridges," "Non-HP Ink Cartridges," "Empty Ink Cartridges," or "Insufficient Ink"

Solution: These are common informational messages from the printer manufacturer. Simply click the "Continue" or "OK" button on your printer or computer screen to proceed with printing. The cartridges will function normally.

Issue 2: Cannot Print Color

Solutions:

  1. Check Protective Tape: Confirm that the blue transparent tape protecting the nozzle has been completely removed from the cartridge.
  2. Nozzle Check: Lightly scratch the nozzle of the color cartridge on a paper towel. If no ink color appears, proceed to the next step.
  3. Soak Nozzle: Soak the nozzle (ensure the copper-colored chip is NOT submerged) in a container of 60-degree warm water for 10-30 seconds. The water depth should only cover the nozzle.
  4. Cartridge Condition: If there is still no ink after these steps, the ink cartridge may be empty or faulty. If it's a new cartridge, contact the seller for assistance.

Issue 3: Printer Prompts "Cartridge Failure," "Cartridge Problem," or "Ink Cartridge Problem"

Solutions: These issues are typically related to the printer not recognizing the cartridge chip.

  1. Reset Printer: Try opening and closing the ink tank door, or restart your printer.
  2. Clean Chip: If the problem persists, carefully wipe the copper-colored contacts (chip) on the ink cartridge with an eraser or a cotton swab lightly dampened with alcohol.
  3. Test Again: Reinstall the cartridge and test on the machine.
  4. Contact Support: If the issue remains unresolved, contact the seller for further testing or a replacement.

Specifications

FeatureDetail
Cartridge ModelHP62 62xl
ColorBlack & Tri-color
Cartridge StatusFull With Ink
Ink TypeDye ink
Ink VolumeBlack: 18ml, Tri-color: 18ml
Page YieldBlack: 600 pages, Tri-color: 450 pages (at A4 Format, 5% Coverage)
Compatible BrandHP
FeatureCompatible
OriginMainland China
TypeInk Cartridge
Compatible Printers
  • HP OfficeJet 200/200c/250/250c/258/5740/5741/5742/5743/5744/5745/5746/8040/8045
  • HP Envy 5540/5541/5542/5543/5544/5545/5546/5547/5548/5549/5640/5642/5643/5644
  • HP Envy 5645/5646/5660/5661/5663/5664/5665/7640/7643/7644/7645/8000/8005
Ink Cartridge Advantages

Image: Diagram highlighting the advantages of the ink cartridge, including "The Latest Chips," "Prevent ink leakage," "Display Ink Volume," and "Bright Colors."

User Tips

  • Compatibility Check: Always double-check that your printer model is explicitly listed as compatible to ensure proper function.
  • Refillable Design: These cartridges are designed to be easily refilled, offering a cost-effective printing solution. Follow the refill guide carefully.
  • Regular Use: To maintain optimal performance and prevent nozzle clogs, use your printer at least once or twice a week.

Warranty and Support

For any issues not covered in this manual, or for warranty claims, please contact the seller directly through your purchase platform. Provide your order details and a clear description of the problem for prompt assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.