Fosi Audio SW10

Contents

Fosi Audio SW10 10-Inch Powered Subwoofer User Manual

Model: SW10

Fosi Audio SW10 10-Inch Powered Subwoofer

Fosi Audio SW10 10-Inch Powered Subwoofer

Introduction

Thank you for purchasing the Fosi Audio SW10 Active Subwoofer.

The SW10 embodies a modern, minimalist design philosophy that blends seamlessly into various home décor styles, providing an aesthetically pleasing balance to living rooms, studies, or home theaters. Acoustically fine-tuned by Fosi Audio experienced experts, this subwoofer features a powerful built-in amplifier that delivers deep, resilient bass. Whether it's explosive scenes in movies or rhythmic beats in music, the SW10 creates an immersive audio experience that brings every moment to life. More than just a high-performance subwoofer, the SW10 is the perfect combination of style and function for modern home audio systems.

Product Overview: Controls and Interfaces

Rear panel of the Fosi Audio SW10 Subwoofer with controls and input/output ports

Rear panel of the Fosi Audio SW10 Subwoofer, illustrating controls and input/output ports.

  1. Crossover Knob: Adjusts the upper frequency limit of the subwoofer.
  2. Phase Control Knob: Adjusts the phase of the subwoofer output relative to the main speakers.
  3. Volume Control Knob: Controls the output volume level of the subwoofer.
  4. RCA Output Port: For connecting to another powered subwoofer or amplifier.
  5. LFE and RCA 2-in-1 Input Port: Audio input for LFE or stereo RCA signals.
  6. Input Selector: Switches between LFE and LINE IN input modes.
  7. EQ Switch: Selects between EQ1 (Enhanced bass for movies/entertainment) and EQ2 (Better bass reproduction for HiFi music).
  8. Auto Power Switch: Enables or disables the automatic power on/standby feature.
  9. Power Switch: Turns the subwoofer on or off.
  10. AC Power Input: Connects the subwoofer to the AC power supply.

Package Contents

  • Fosi Audio SW10 Subwoofer unit Fosi Audio SW10 Subwoofer
  • 1.8m Power Cable 1.8m Power Cable
  • User Manual cover User Manual (PDF available at Download PDF)

Setup Guide

Position the subwoofer in an optimal location, ideally near the main stereo speakers and close to a corner for enhanced bass response.

LFE Input Connection

  1. Connect the subwoofer signal cable to the LFE input jack on the back of the subwoofer.
  2. Connect the same subwoofer signal cable to the SUB OUT or LFE output of your audio source.
  3. Set the input mode selector switch to "LFE."
  4. Plug the power cord into the wall outlet and connect to power. Turn the power switch to "ON" (It is recommended to also set the auto power switch to "ON").

RCA Input Connection

  1. Connect the subwoofer signal cable to the RCA input jack on the back of the subwoofer.
  2. Connect the subwoofer signal cable to the LINE OUT or RCA output of your audio source.
  3. Set the input selector switch to "LINE IN."
  4. Plug the power cord into the wall outlet and connect to power. Turn the power switch to "ON" (It is recommended to also set the auto power switch to "ON").

Operating Guide: Audio Settings

1. Crossover Settings

The SW10 offers a crossover range of 40Hz to 180Hz, which can be adjusted using the crossover knob on the back of the subwoofer. For example, when the crossover is set to 80Hz, the subwoofer will only play bass frequencies from 40Hz to 80Hz.

Diagram showing the 10-inch driver and sound propagation with frequency range

Illustration of the 10-inch driver and its frequency response.

2. Auto-Power Switch

When the switch is activated, the subwoofer will automatically power on upon detecting a signal from the audio source. The LED indicator will turn blue. When the subwoofer is operating normally and no audio signal is detected for 15 minutes, it will automatically enter standby mode. The LED indicator will turn red.

Image showing automatic wake-up/standby feature

Visual representation of the automatic wake-up/standby feature, activating after 15 minutes of no signal.

3. Phase Adjustment

The SW10 offers 0° to 180° phase adjustment, which can be set using the phase knob on the back of the subwoofer. Due to factors such as speaker placement and room reflections, the low-frequency waves from the main speakers and the subwoofer may not be synchronized, resulting in bass cancellation. Adjusting the phase setting allows the SW10 to stay in phase with other speakers, enhancing the overall listening experience.

Specifications

Feature Description
Speaker Structure Down-firing Active Subwoofer with Built-in Amplifier Driver
Driver 10-inch Polypropylene Cone with Rubber Surround
Input RCA, LFE
Power Output RMS 200W (500W Peak)
Frequency Response 35Hz-180Hz
Dimensions 360mm x 360mm x 400mm (14.17 x 14.17 x 15.75 in)
Weight 14 kg
Auto-Power Feature Supported
Power Supply AC 100-240V ~ 50/60Hz, 200W
Cabinet Material Metal
Audio Crossover Full-Range
Visual representation of the 10-inch subwoofer driver and 500W power output

The 10-inch large driver with polypropylene diaphragm delivers layered bass without masking mids and highs, supported by a D-Class Amp Chip for powerful, low-distortion bass.

Diagram illustrating the down-firing design for natural bass

Down-firing design protects the driver and uses floor reflections for smoother, more pleasing sound.

Illustration of greater airflow with dual ports for deeper bass

Compared to single-port designs, the dual-port system delivers deeper and fuller bass with greater airflow.

Troubleshooting

1. No Power?

  • Ensure the subwoofer is connected to a reliable power source.
  • Verify that the power switch is set to ON.
  • Check that the power indicator light is illuminated.

2. No Sound Output?

  • Confirm the subwoofer is powered on, indicated by a blue LED.
  • Check whether the connection cables are correct.
  • Verify that the audio source is outputting sound properly.
  • Check whether the volume control is set too low.

3. Distorted Sound?

  • Check for proper phase alignment.
  • Inspect the driver unit for any damage.

4. How to Adjust Volume or Crossover?

Volume and crossover frequency can be adjusted using the respective knobs on the back of the SW10.

5. What is Auto Power?

When in standby mode, the unit will automatically switch to working mode when an audio signal is detected. When operating, the unit will automatically enter standby mode if no audio signal is detected.

6. What is Phase Adjustment?

It is used to synchronize the sound waves of the subwoofer with those of the main speakers, achieving fuller and more powerful bass performance.

7. What do the LED Status Indicators Mean?

  • Blue indicates normal operation.
  • Red signifies that the device is in standby status.

8. What is the RCA output interface used for?

The RCA output provides a line-level audio signal, typically used to connect a second powered subwoofer for enhanced bass. It can also connect to an amplifier or active speaker, offering an extra signal path when there is no dedicated subwoofer output.

Tip: If you still experience issues, please contact our support team via email: support@fosiaudio.com

User Tips

  • Optimal Placement: Experiment with subwoofer placement. Placing it in a corner or near a wall can often enhance bass output, but listen for the best balance in your room.
  • Phase Matching: If your main speakers and subwoofer sound thin or lack impact, try adjusting the phase control. Small adjustments can significantly improve bass integration.
  • Crossover Tuning: Adjust the crossover frequency to seamlessly blend the subwoofer's output with your main speakers. A good starting point is often around 80Hz, but it depends on your main speakers' low-frequency capabilities.
  • Volume Balance: Set the subwoofer volume so that it complements your main speakers without overpowering them. The bass should feel like a natural extension of your audio, not a separate component.
  • EQ Modes: Utilize the EQ switch (EQ1 for enhanced bass in movies, EQ2 for balanced HiFi music) to tailor the sound profile to your content.

Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the subwoofer. Avoid using harsh chemicals or abrasive cleaners, as they may damage the finish.
  • Ventilation: Ensure adequate ventilation around the subwoofer to prevent overheating. Do not block any vents.
  • Placement: Keep the subwoofer away from direct sunlight, heat sources, and moisture.
  • Power Off: When not in use for extended periods, it is recommended to turn off the subwoofer using the main power switch and unplug it from the power outlet.

Warranty and Support

Fosi Audio pledges a 24-month limited warranty and support from the date of purchase. If you encounter any problem when using our product, please contact our support team at support@fosiaudio.com.

About Us

Fosi Audio designs and builds innovative audio products with all your music in mind. Great sound, simple but elegant designs, high-quality components, and truly useful features are what Fosi Audio pursues. We sincerely hope you can get as much enjoyment from our products as we've had to create them!

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.