1. Product Overview
This product is a decorative emblem sticker designed for Audi A4 and A6 vehicle rear trunks. Made from durable ABS material, it provides a stylish and authentic look to your vehicle.

Figure 1: Assortment of A4 and A6 emblems
2. Safety and Warnings
- WARNING: CHOKING HAZARD. Small parts. Keep out of reach of children under 3 years old.
- WARNING: SHARP EDGES. Handle with care during application. Not for children under 3 years.
- Ensure proper disposal of packaging materials.
3. Setup and Installation
Follow these steps for proper installation of your car emblem sticker:
- Prepare the Surface: It is best to clean the application area on your vehicle's rear trunk with alcohol. Ensure the surface is completely dry and free from water, oil, dust, or wax. Do not apply the sticker to a car that has been waxed recently.
- Choose Placement: According to the sticker's size (8.5cm x 2.3cm), choose a flat and suitable place on the trunk for application.
- Apply the Sticker: Carefully tear off the protective film from the 3M adhesive tape on the back of the emblem. Position the emblem precisely on the chosen spot.
- Secure the Emblem: Press the emblem firmly and evenly for a moment to ensure strong adhesion. Avoid washing the car for at least 24-48 hours after application to allow the adhesive to fully cure.

Figure 2: Emblem dimensions and adhesive backing
Video 1: Demonstration of emblem variants and application process
4. Operating Instructions
Once properly installed, the emblem serves as a permanent decorative and branding accessory for your vehicle. No further operation is required.
5. Maintenance
- Cleaning: To clean the emblem, gently wipe it with a soft, lint-free cloth. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
- Storage (if not yet applied): Store the emblem in a dry place at room temperature (approximately 15°C - 35°C) away from direct sunlight and extreme temperatures.
6. Troubleshooting
- Emblem not adhering well: Ensure the surface was thoroughly cleaned and dry before application. Apply firm, even pressure during installation. Avoid applying in very cold temperatures.
- Emblem peeling off: This usually indicates improper surface preparation or insufficient pressure during initial application. If peeling occurs, the adhesive may be compromised, and reapplication with a new adhesive or emblem might be necessary.
7. Specifications
| Item Type | Emblems |
| Special Features | Car Badge Sticker |
| Material | ABS |
| Item Weight | 7g |
| Item Width | 0.9 inch (2.3 cm) |
| Item Length | 3.34 inch (8.5 cm) |
| Model Name | A4 A6 Emblem |
| Car Maker | Audi |
| Origin | Mainland China |
| High-concerned chemical | None |
| Package Weight | 0.012 kg |
| Package Dimensions | 15 cm x 12 cm x 1 cm |
8. User Tips
- For the best and most lasting adhesion, ensure the application surface is meticulously clean and dry.
- Before removing the adhesive backing, temporarily place the emblem on the desired spot to confirm alignment and positioning.
- The emblems are designed to match original sizes, ensuring a good aesthetic fit.
9. Warranty and Support
For any inquiries or support regarding your Audi A4 A6 Car Emblem Sticker, please contact the manufacturer or authorized representative:
Manufacturer:
Wuhan Yunhaolian Technology Co., Ltd
Address: No. 02-1DGG139, 2nd Floor, Building C9, Group 2, Wuhan Software New City Phase II, No. 8 Huacheng Avenue, Donghu New Technology Development Zone, Hongshan District, Wuhan Hubei Province
TEL: 86-15171436333
Email: hylsll25@163.com
EU Authorized Representative:
MJCM SARL
Address: 78 avenue des Champs, Elysees Bureau 326, Paris, France, 75008
TEL: 33-752907452
Email: mjcm190928@gmail.com
A detailed user manual in PDF format is also available for download: View User Manual (PDF)