Audi Q4 e-tron Emblem

Contents

Audi Q4 e-tron Car Emblem Instruction Manual

Model: Q4 e-tron Emblem

1. Product Overview

This product is a 3D ABS car emblem designed for Audi Q4 e-tron and Q6 vehicles. It features self-adhesive backing for easy installation on the car's rear trunk or fender side. Available in various finishes, including black and chrome.

Overview of Q4 and e-tron emblems in black and chrome finishes.
Figure 1: Overview of Q4 and e-tron emblems in black and chrome finishes.

2. Safety & Warnings

  • WARNING: CHOKING HAZARD. Keep out of reach of children under 3 years old.
  • Be careful of sharp edges during handling and installation.
  • Ensure the installation surface is clean and dry to prevent the emblem from detaching, which could create a hazard.
CE mark and recycling symbols
Figure 2: Compliance and Recycling Symbols. This product should be disposed of responsibly and not as household waste.

3. Setup and Installation

Follow these steps for proper installation of your car emblem:

  1. Prepare the Surface: It is best to clean the intended installation area on your vehicle with alcohol. Ensure the surface is completely dry and free from water, oil, dust, or wax. Avoid applying the emblem to a car that has been recently waxed.
  2. Choose Placement: Based on the emblem's size, select a flat and suitable location on the car's rear trunk or fender side.
  3. Apply the Emblem: Carefully tear off the protective film from the 3M adhesive tape on the back of the emblem.
  4. Secure the Emblem: Position the emblem precisely and press it firmly onto the surface for a moment to ensure strong adhesion.
Hand holding Q4 chrome and e-tron black emblems, showing adhesive backing.
Figure 3: Example of emblem with adhesive backing ready for application.

4. Operating Instructions

Once properly installed, the emblem requires no further operation. Its purpose is decorative and to identify your vehicle model. Ensure it is securely attached to prevent accidental detachment.

5. Maintenance & Storage

  • Cleaning: To clean the emblem, use a soft, lint-free cloth dampened with water or a mild car-safe cleaning solution. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
  • Storage: If the emblem is not immediately used, store it in its original packaging in a dry place at room temperature (15°C - 35°C) to protect the adhesive and finish.

6. Troubleshooting

  • Emblem not sticking: Ensure the surface was thoroughly cleaned with alcohol and completely dry before application. Avoid applying to recently waxed surfaces. Apply firm, even pressure for at least 30 seconds during installation.
  • Emblem appears crooked: Carefully remove the emblem if possible without damaging the adhesive or paint, clean the surface again, and reapply with precision.

7. Specifications

Feature Detail
Product Name Q4 e-tron Badge Sticker
Material ABS
Item Type Emblems
Special Features Car Badge Sticker
Car Maker Audi
Model Name Q4 e-tron Emblem
Item Weight 9g
Q4 Emblem Size 10.2cm (4.01inch) Length * 2.4cm (0.94inch) Width
e-tron Emblem Size 11cm (4.33inch) Length * 1.1cm (0.433inch) Width
Origin Mainland China
High-concerned chemical None
Diagram showing dimensions of Q4 and e-tron emblems.
Figure 4: Detailed dimensions of the Q4 and e-tron emblems.

For a comprehensive user manual, please refer to the official PDF document: User Manual (PDF).

8. User Tips

  • Color Matching: When purchasing multiple emblems (e.g., an Audi emblem and an e-tron emblem), ensure you select the same color option (e.g., black or chrome) for a consistent look.
  • Black Finish: The black finish for the e-tron emblem is typically glossy, not matte, providing a sleek appearance.

9. Warranty & Support

For any product inquiries, support, or warranty information, please contact the manufacturer directly:

  • Manufacturer: Wuhan Yunhaolian Technology Co., Ltd
  • Address: No. 02-1DGG139, 2nd Floor, Building C9, Group 2, Wuhan Software New City Phase II, No. 8 Huacheng Avenue, Donghu New Technology Development Zone, Hongshan District, Wuhan Hubei Province
  • Telephone: 86-15171436333
  • Email: hylsll25@163.com

EU Authorized Representative:

  • Company Name: MJCM SARL
  • Address: 78 avenue des Champs, Elysees Bureau 326, Paris, France, 75008
  • Telephone: 33-752907452
  • Email: mjcm190928@gmail.com

© 2024 All rights reserved. This manual is for informational purposes only.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.