1. Introduction
The LAUNCH Creader Professional 129i V3 is an advanced diagnostic solution designed for passenger cars. It leverages LAUNCH's cutting-edge diagnostic technology to offer extensive vehicle coverage, powerful functions, and precise test results.
Key Features:
- 4 System Diagnostics: Deep inspection of Engine, ABS, SRS, and Transmission systems.
- 12 Reset Service Functions: Including Oil Lamp Reset, Electronic Parking Brake (EPB) Reset, Steering Angle Calibration (SAS), Tire Pressure Monitor System (TPMS) Reset, Electronic Throttle Position Reset, DPF Regeneration, Injector Coding, Battery Management System (BMS) Reset, ABS Bleeding, Adblue Reset, AFS Headlamp Reset, and Air/Fuel Ratio Reset.
- Full OBD2 Functions: Supports all 10 modes of OBD II test.
- Lifetime Free Online Updates: Ensures the software is always up-to-date with new functions, bug fixes, and support for newer car models.
- 5-inch Touchable HD 720P Screen: Intuitive user interface.
- Wi-Fi/Hotspot Connection: For updates and online features.
- Auto VIN & Auto Scan: Quickly identifies vehicle information.
- Diagnostic Report: Generates and allows sharing/printing of detailed reports.
- DTC Lookup Library: Built-in database for diagnostic trouble code definitions.
- Live Data Stream: Displays real-time data in text, graph, and combined formats (4-in-1 graphing).
- Battery Voltage Test: Monitors vehicle battery health in real-time.
- Online Feedback: Submit diagnostic issues for expert assistance.
- Wide Vehicle Coverage: Supports over 85 car brands and 100,000+ vehicle models.
- Multi-language Support: English, French, Spanish, German, Korean, Japanese, Portuguese, Italian, Traditional Chinese, Polish, Russian.

2. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or this tool, please read this user's manual carefully and observe the following safety precautions at a minimum whenever working on a vehicle:
- Always perform automotive testing in a safe environment.
- Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
- Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged.
- Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
- Don't connect or disconnect any test equipment while the ignition is on or the engine is running.
- Keep this tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the tool, when necessary.
- Please use the DC 5V power adaptor to charge this tool. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the right one.
FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device has been evaluated to meet general RF exposure requirement. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Professional Diagnostic Tool with model Creader Professional 123i/129i has been tested against this SAR limit. The highest reported SAR values for body-worn is 1.19 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0mm from the body. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
EU Declaration of Conformity:Hereby, Launch Tech Co., Ltd declares that the Creader Professional 123i/129i of Professional Diagnostic Tool is in compliance with Directive 201/53/EU. The full text of the EU declaration of conformity is available at: http://www.cnlaunch.com/
Operation Frequency: WiFi 802.11b/g/n HT20:2412-2472MHz; 802.11n HT40:2422-2462MHz
Max. RF Output power: Wifi(2.4G): 19.88dBm
The RF frequencies can be used in Europe without restriction.
3. Product Components & Controls
The LAUNCH CRP129I V3 features a robust, non-slip hand-held design for comfortable use. Below is an overview of its components and controls.

Device Layout:
- 5-inch Touchable HD 720P Screen: For displaying test results and navigating menus.
- Navigation Keys: Up, Down, Left, Right arrows for menu selection.
- OK Button: Confirms selections or actions.
- Return Button: Exits current program or returns to the previous screen.
- Home Button: Returns to the main Job Menu screen.
- Power Button: Turns the device on/off and activates/deactivates the LCD.
- 5V Charging Port: For connecting the DC 5V charging cable.
- Diagnostic Port (DB-15 connector): For connecting the diagnostic cable to the vehicle's DLC.
- Charging LED: Red indicates charging, Green indicates fully charged.
Accessories Checklist:
- Creader Professional 129i V3 Handset
- OBD II Diagnostic Cable
- DC 5V Charging Cable
- User Manual
- Quick Start Guide
- Carrying Bag
4. Technical Specifications
| Feature | Specification |
|---|---|
| Screen | 5-inch touch screen |
| Operating System | Android 7.1 |
| Processor | A5 Quad Processor |
| RAM | 2G |
| ROM | 16GB |
| Battery Capacity | 6100 mAh |
| OBDII Input Voltage Range | 9~18V |
| Input Method | Touch & Keypad |
| Charging | DC 5V charging cable, Diagnostic cable via DLC |
| Dimensions | 228mm x 125mm x 34.5mm |
| Net Weight | <565g |
| Working Temperature | -10 to 50°C (14 to 122 F°) |
| Storage Temperature | -20 to 70°C (-4 to 158 F°) |
| Wireless Function | Bluetooth, Wifi |
| External Testing Certification | CE |
5. Setup and Initial Use
5.1 Charging the Tool
The tool can be charged using two methods:
- Via Charging Cable: Plug one end of the included charging cable into the DC-IN port of the tool, and the other end to an external DC power source.
- Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle's Data Link Connector (DLC).
The Charging LED will illuminate solid green when the battery is fully charged.
5.2 Getting Started (First-time Use)
- Press the [Power] button to turn on the device.
- The welcome page will appear. Tap "Start" to proceed.
- Choose your desired system language and tap "Next".
- Select your time zone and tap "Next" to enter the WLAN setup page.
- Slide the Wi-Fi switch to ON. The system will search for available wireless networks. Select your desired network and connect.
- After network connection, tap "Next Step" to configure your email address. Input your email and tap "Next Step".
Note: It is highly recommended to provide a valid email address. Diagnostic reports will be automatically sent to this email after a complete Auto-Detect process. - Read and accept the user agreement by checking the box "Agree to all the above terms" and tapping "OK". This will complete the sign-up process and navigate to the Job Menu.
6. Operation
6.1 Connection to Vehicle
- Turn the vehicle ignition off.
- Locate the vehicle's Data Link Connector (DLC). This is typically a 16-pin connector located about 12 inches from the center of the dashboard, under or around the driver's side. If not found, refer to the vehicle's service manual.
- Plug one end of the diagnostic cable into the DB-15 connector of the tool and tighten the captive screws. Connect the other end to the vehicle's DLC.

6.2 System Diagnosis
This function is designed for diagnosing electronic control systems of a single vehicle model.
Smart Diagnosis (Auto-Detect)
After proper connection and with the ignition key on, the system will automatically enter auto-detect mode (ensure "Automatic detection on connect" is ON in Settings). The tool will attempt to obtain the Vehicle Identification Number (VIN). If successful, it will proceed with scanning vehicle systems and generate a diagnostic report, which will be sent to your configured email address.
If VIN detection fails, you may be prompted to manually input the VIN. If manual VIN input also fails, the tool will enter manual diagnosis mode.
Manual Diagnosis
If auto-detect fails, you can manually select the vehicle make, model, and system to diagnose. Follow the on-screen instructions:
- From the Job Menu, select "Diagnose".
- Choose the diagnostic software version (e.g., "DEMO").
- Select the desired test item (e.g., "System Selection").
- Choose the specific system (e.g., Engine Control Module - ECM, Transmission Control Module - TCM, Anti-lock Braking System - ABS, Supplemental Restraint System - SRS).
- Available functions include:
- Version Information: Reads system mode, VIN, software, and ECU information.
- Read Fault Code (DTCs): Displays detailed information of Diagnostic Trouble Codes.
- Freeze Frame: Records vehicle operating parameters at the time an emission-related fault occurs.
- Code Search: Provides more information about DTCs online.
- Clear Fault Memory: Erases DTCs and turns off warning lights after repairs. Note: Ensure ignition is ON and engine is OFF before clearing codes. Do not clear codes if you plan to take the vehicle to a service center, as it erases valuable diagnostic information.
- Read Data Stream: Retrieves and displays live data and parameters from the vehicle's ECU. Data can be viewed in Value (text), Graph (waveform), or Combine (multiple graphs for comparison) modes.

6.3 Full OBDII Test Modes
From the Job Menu, select "OBD II" to access the following functions:
- Read Codes: Identifies which section of the emission control system has malfunctioned.
- Erase Codes: Turns off the Check Engine Light (MIL), clears codes, and resets monitors.
- I/M Readiness: Indicates whether emission-related systems are operating properly and are ready for inspection/maintenance testing.
- View Freeze Frame: Displays a snapshot of operating conditions when an emission-related fault occurred.
- O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results.
- On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
- EVAP System Test: Initiates a leak test for the vehicle's EVAP system.
- Vehicle Info: Displays VIN, Calibration ID (CID), and Calibration Verification Number (CVN).
- Data Stream: Displays live data parameters.

6.4 Maintenance and Reset Functions (CRP129i V3 Only)
The CRP129i V3 offers 12 commonly used maintenance and reset functions. From the Job Menu, select "Reset" and choose the desired service function and car brand. Follow the on-screen instructions to complete the process.

- Oil Lamp Reset: Resets the service light after changing engine oil or monitoring appliances.
- Electronic Parking Brake (EPB) Reset: Replaces brake pads, diagnoses caliper functionality, initializes wear indicators, and deactivates/reactivates the brake control system.
- Steering Angle Calibration (SAS Reset): Resets the steering angle after replacing steering components or performing wheel alignment.
- Tire Pressure Monitor System (TPMS) Reset: Resets tire pressure and turns off the TPMS MIL after replacing tire sensors.
- Electronic Throttle Position Reset (Throttle Adaptation): Matches the throttle after ECU replacement, throttle assembly replacement/cleaning, or intake pipe replacement/removal.
- DPF Regeneration: Used after replacing exhaust back pressure sensors, PM traps, fuel additive nozzles, catalytic oxidizers, or when the DPF regeneration MIL is on.
- Injector Coding: Writes or rewrites injector codes in the ECU for accurate fuel injection control, especially after replacing the ECU or injectors.
- Battery Management System (BMS) Reset: Required after replacing the main battery or battery monitoring sensor.
- ABS Bleeding: Performs ABS brake bleeding to ensure a firm brake pedal after air exhaustion.
- Adblue Reset: Required after replacing or filling up diesel exhaust treatment fluid (car urea).
- AFS Headlamp Reset: Initializes the adaptive headlamp system.
- Air/Fuel Ratio Reset: Improves fuel economy.
6.5 Data View and Management
The "Data" module on the Job Menu provides access to various data management functions:
- Diagnostic Report: Stores all generated diagnostic reports, sorted by date and make. Reports can be filtered, viewed, and deleted.
- Diagnostic Record: Saves recorded running parameters or waveform graphs from live data streams. These can be played back in text or graph format.
- DTC Library: Allows you to look up definitions of Diagnostic Trouble Codes.
- DLC (Data Link Connector) Location: Helps locate the vehicle's DLC.
- Feedback: Submit diagnostic problems to LAUNCH for analysis and troubleshooting.
- Firmware Fix: Used to upgrade and fix diagnostic firmware. Do not interrupt power during this process.

6.6 Settings
The "Settings" module on the Job Menu allows you to configure various device parameters:
- Units of Measurement: Set to Metric or English System.
- Automatic Detection on Connect: Enable/disable automatic VIN detection upon connection.
- Display & Brightness: Adjust standby time and screen brightness.
- Sound: Adjust volume and other sound settings.
- Network: Configure Wi-Fi connection.
- Date/Time: Set system date and time.
- Language: Change the operating language.
- Email Setup: Configure the default email address for diagnostic reports.
- Recovery: Reset the tool to default factory settings. Warning: This may cause data loss.
- Clean Up: Clear cache files and free up storage space.
- About: Displays hardware configuration and license agreement.
7. Maintenance
7.1 Software Updates
The CRP129I V3 supports lifetime free online updates. When new software or APK updates are available, a numeric indicator will appear on the "Upgrade" module in the Job Menu. It is highly recommended to update regularly to ensure optimal performance, new features, and expanded vehicle coverage.
- Ensure a stable internet connection.
- Tap "Upgrade" on the Job Menu to enter the update center.
- By default, all diagnostic software is selected. You can deselect specific software if needed.
- Tap "Update" to start downloading. This process may take several minutes. Do not interrupt the download.
- If the network connection fails, tap "Retry".
- Once downloaded, the software packages will be installed automatically.
7.2 Device Care
- Keep the tool dry, clean, and free from oil, water, or grease.
- Use a mild detergent on a clean cloth to clean the exterior of the tool when necessary.
- Avoid dropping the device or subjecting it to strong impacts.
- Store the device in a cool, dry place when not in use.
8. User Tips
- Regular Updates: Always keep your scanner's software updated to ensure compatibility with the latest vehicle models and access to new diagnostic features.
- Stable Connection: For accurate VIN detection and reliable diagnostic results, ensure a stable connection to the vehicle's DLC and a strong Wi-Fi signal for updates and online features.
- Battery Management: Monitor the battery voltage regularly, especially before long diagnostic sessions, to avoid interruptions.
- Diagnostic Reports: Utilize the diagnostic report feature to save and share findings, which can be helpful for tracking vehicle health over time or consulting with mechanics.
- DTC Lookup: Don't just clear codes; use the built-in DTC library and Google search function to understand the root cause of the problem before attempting repairs.
9. Troubleshooting (FAQ)
Q1: System halts when reading data stream. What is the reason?
A1: This may be caused by a slackened connector. Please turn this tool off, firmly connect the connector, and switch it on again.
Q2: Screen of main unit flashes at engine ignition start.
A2: This is caused by electromagnetic disturbing and is a normal phenomenon.
Q3: There is no response when communicating with the on-board computer.
A3: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is at proper temperature.
Q4: What to do if the system fails to start auto VIN detection?
A4: Please check the following possible reasons:
- Whether the tool is properly connected to the vehicle's DLC.
- Whether the "Automatic detection on Connect" switch is OFF. If yes, slide it to ON.
Q5: Why are there so many fault codes?
A5: Usually, it's caused by poor connection or fault circuit grounding.
Q6: How to upgrade the system software?
A6:
- Switch the tool on and ensure a stable internet connection.
- Tap "Setting" on the Job Menu, select "About" -> "Version", and tap "Detect the System Version" to enter the system upgrading page.
- Follow the on-screen instructions step by step to finish the process. It may take several minutes depending on the internet speed, please be patient. After upgrade is successfully finished, the tool will automatically restart and enters the Job menu.
Q7: What if the tool cannot be switched on even after a period of recharging?
A7: Please recharge it for at least 3 hours until the power LED lights up, then it can be switched on.
10. Warranty and Support
10.1 Warranty Information
This LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with established procedures. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
10.2 Customer Service
If you have any questions on the operation of the unit, please contact your local dealer, or contact LAUNCH TECH CO., LTD. directly:
- Website: www.x431.com or www.cnlaunch.com
- Phone: +86 755 8455 7891
- Email: overseas.service@cnlaunch.com
Statement: LAUNCH reserves the rights to make any change to this manual without notice. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable. If you have any questions, please contact your local dealer or LAUNCH TECH CO., LTD. LAUNCH does not bear any responsibility arising from misunderstandings.