1. Product Information
This manual provides instructions for the installation, maintenance, and general use of the AUDI RS3 Sport Emblem, 4-Ring Logo, and RS3 Badge Stickers. These decorative stickers are designed for various placements on your AUDI RS3 vehicle.
- Product Name: AUDI RS3 Sport Emblem, 4-Ring Logo, ABS Black Car Hood Front Grill Rear Trunk Badge Sticker
- Model Compatibility: AUDI RS3 2016-2020
- Item Type: Stickers
- Material: ABS Plastic
- Color: Black
2. Safety & Warnings
Please read all safety information before handling or installing the product.
- ATTENTION: Not suitable for children under 36 months due to small parts.
- Do not use this product for purposes other than its intended decorative use on vehicles.
- Inspect the product for any damage before each use or installation. Do not use if the product appears damaged.
- Follow all installation and operation guidelines carefully to avoid personal injury or damage to the product or vehicle.
3. Setup and Installation
These emblems and badges are designed for direct installation. Proper surface preparation is crucial for optimal adhesion.
Figure 1: Complete set of AUDI RS3 Sport Emblem, 4-Ring Logo, and RS3 Badge Stickers.
Installation Steps:
- Prepare the Surface: Thoroughly clean the area on your vehicle where the emblem will be applied. Use a mild automotive cleaner or isopropyl alcohol to remove all dirt, wax, grease, and residues.
- Dry the Surface: Ensure the application surface is completely dry before proceeding. Any moisture will compromise adhesion.
- Temperature Consideration: For best results, install in a moderate temperature environment (ideally 15-25°C / 60-77°F). Avoid extreme cold or direct hot sunlight during installation.
- Remove Protective Film: Carefully peel off any protective films from the front surface of the emblem, if present.
- Peel Adhesive Backing: Gently peel off the protective backing from the adhesive side of the emblem. Avoid touching the adhesive with your fingers.
- Position the Emblem: Carefully align the emblem to the desired position on your vehicle. Take your time to ensure it is straight and centered.
- Apply Pressure: Once positioned, firmly press the emblem onto the surface for at least 30-60 seconds. Apply even pressure across the entire emblem to ensure full contact with the adhesive.
- Curing Time: Avoid washing the vehicle or exposing the emblem to excessive moisture for at least 24-48 hours to allow the adhesive to fully cure.
4. Operating Instructions
Once properly installed, these emblems and badge stickers are purely decorative and require no operational input. They are designed to enhance the aesthetic appeal of your vehicle.
5. Maintenance
Cleaning:
- Clean the emblems with a soft cloth and mild automotive soap and water.
- Avoid using abrasive cleaners, harsh chemicals, or high-pressure washers directly on the emblems, as this may damage the finish or compromise the adhesive.
- Rinse thoroughly with clean water and dry with a soft cloth.
Inspection:
- Periodically inspect the edges of the emblems to ensure they remain firmly adhered to the vehicle surface.
- If any lifting is noticed, gently press down on the affected area. If lifting persists, reapplication may be necessary.
6. Troubleshooting
Emblem Not Sticking or Peeling:
- Issue: Emblem does not adhere well or starts to peel shortly after installation.
- Possible Causes:
- Application surface was not thoroughly cleaned or dried.
- Surface temperature was too low during installation.
- Insufficient pressure was applied during installation.
- Adhesive was contaminated (e.g., touched by fingers).
- Vehicle was washed or exposed to moisture too soon after installation.
- Solution: Ensure proper surface preparation, temperature, and application technique. If peeling occurs, the emblem may need to be removed, the surface cleaned, and a new emblem applied.
7. Specifications
| Feature | Specification |
|---|---|
| Item Type | Stickers |
| Sticker Placement | The Whole Body (various locations) |
| Model Compatibility | AUDI RS3 2016-2020 |
| Brand Name | Audi |
| Material | ABS Plastic |
| Color | Black |
| Package Length | 31 cm |
| Package Width | 14 cm |
| Package Height | 5 cm |
| Package Weight | 0.123 kg |
8. User Tips
- Surface Preparation is Key: The most common reason for poor adhesion is inadequate surface cleaning. Take extra time to ensure the area is spotless and completely dry.
- Pre-fit Before Peeling: Before removing the adhesive backing, temporarily place the emblem on the desired location to visualize the final placement and ensure proper alignment.
- Warm Surface for Better Adhesion: If installing in cooler temperatures, gently warm the application surface with a hairdryer (on a low setting) before applying the emblem. This can help the adhesive bond more effectively.
9. Warranty & Support
No specific warranty information is provided with this product. For any support inquiries, please contact the manufacturer or their authorized representative.
Manufacturer Information:
- Company Name: Guangzhou Xuezhang Trading Co., Ltd
- Full Address: Room C1113, No. 36 Gaokeliu, Tianhe District, Guangzhou City, Guangdong Province, China, 607-613
- Email: xz502452959@163.com
EU Authorized Representative:
- Company Name: MJCM SARL
- Full Address: 78 avenue des Champs Elysees Bureau, 326 Paris Ile-de-France
- Email: mjcm190928@gmail.com
A digital version of this manual is available for download: User Manual (PDF)