1. Introduction
Thank you for choosing the Koso Mini 4-in-1 Motorcycle Digital Meter. This compact and versatile device provides essential information for your motorcycle, including RPM, water temperature, voltage, and time, all displayed on a clear LED screen. This manual will guide you through the installation, operation, and maintenance of your new digital meter.


2. Safety Information
- Always confirm model and year compatibility before installation.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Regularly inspect all hardware for peak performance and component tightness.
- Ride safely and periodically check the tightness of all installed components.
- If you are unsure about any installation steps, consult a qualified motorcycle technician.
3. Package Contents
Please check the package for the following items:
- Koso Mini 4-in-1 Digital Meter
- Wiring Harness
- Water Temperature Sensor
- Mounting Bracket
- 3M Adhesive Pads
- Instruction Manual (paper copy)

4. Setup and Installation
4.1. Wiring Connections
Proper wiring is crucial for the correct function of the meter. Refer to the detailed instructions in the included PDF manual for wiring diagrams. General connections are as follows:
- Red Wire: Connect to the positive (+) terminal of your motorcycle's battery.
- Black Wire: Connect to the negative (-) terminal of your motorcycle's battery or a reliable chassis ground point.
- Blue Wire: Connect to a switched power cable that receives power only when the ignition key is turned ON. This ensures the meter turns on and off with your motorcycle.
- White/Purple Wire: Connect this wire just after the ignition coil to receive the RPM signal. Ensure a secure connection for accurate readings.
- Water Temperature Sensor: Install the temperature sensor into your motorcycle's cooling system, typically by using an inline adapter on a radiator hose. Ensure a leak-free connection.
4.2. Mounting the Meter
Use the provided mounting bracket and 3M adhesive pads to securely attach the meter to a suitable location on your motorcycle's handlebars or dashboard. Ensure the location allows for clear visibility while riding and does not obstruct any controls.


5. Operating Instructions
5.1. Power On/Off
The meter will power on automatically when your motorcycle's ignition is turned ON (due to the blue wire connection) and power off when the ignition is turned OFF.
5.2. Switching Display Modes
The meter cycles through its four functions (Water Temperature, RPM, Voltage, Time) by pressing the button on the left side of the unit. Press the button briefly to switch between modes.
5.3. Setting Temperature Units
To switch between Celsius (°C) and Fahrenheit (°F) for water temperature display, press and hold the button on the left side of the unit for a few seconds while in water temperature mode. The display will toggle between the two units.

5.4. Setting Time
Refer to the detailed instructions in the included PDF manual for setting the clock time.
6. Maintenance
- Cleaning: Wipe the meter's screen and body with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically check all wiring connections for tightness and signs of wear or corrosion. Ensure the temperature sensor is securely installed and not leaking.
- Hardware: Regularly inspect the mounting bracket and screws to ensure the meter remains securely attached.
7. Troubleshooting
- Meter does not power on:
- Check the red and black wire connections to the battery.
- Ensure the blue wire is connected to a switched power source and is receiving power when the ignition is ON.
- Check for any blown fuses in your motorcycle's electrical system.
- Incorrect RPM reading or no RPM display:
- Verify the white/purple wire is correctly connected to the ignition coil.
- Ensure the connection is secure and not loose or corroded.
- Incorrect water temperature reading or no display:
- Check the connection of the temperature sensor to the meter's wiring harness.
- Ensure the temperature sensor is properly installed in the cooling system and making good contact with the coolant.
- Inaccurate voltage reading:
- Verify the red and black wires have a solid connection to the battery terminals.
8. Specifications
| Functionality | 4-in-1: RPM, Water Temperature, Voltage, Time |
| Display Type | LED Digital |
| Material | PP (Polypropylene) |
| Origin | Mainland China |
| Package Dimensions (L x W x H) | 17 cm x 11 cm x 3 cm |
| Package Weight | 0.194 kg |
9. User Tips
- When mounting, consider using higher quality double-sided tape than what is provided for a more secure and long-lasting hold.
- Take your time to understand the wiring connections. The blue wire for switched power and the white/purple wire for the coil are key for proper functionality.
- For detailed wiring diagrams and specific instructions, always refer to the comprehensive PDF user manual.
10. Warranty and Support
For detailed warranty information, please refer to your purchase documentation or contact your retailer. For further technical support or detailed wiring diagrams, please consult the official Koso user manual available as a PDF document: View PDF Manual.